Kessler Second Shooter Pro User manual

SETUP & CONFIGURATION
SECOND SHOOTER PRO
TABLE OF CONTENTS
WHAT YOU’LL NEED
• Second Shooter Pro™
• Slider
• Motor
• Mount
• Camera Control Cable
(or external intervalometer)
The Controller...........................................................................2
Getting Started: Hardware Set-Up .........................................................3
• Slider Motor.........................................................................3-5
• Pan & Tilt Axis.........................................................................6
• Intervalometer Connect................................................................6
Using kOS...............................................................................7
Remote App.............................................................................8
• Setting Up PS4 Controller.............................................................8
Bridge Mode............................................................................9
Setting Up a Move ......................................................................10
• Manual Move........................................................................10
• Turntable............................................................................10
• Program Move.......................................................................11
• Loop/Scrub...........................................................................12
• Time Lapse..........................................................................12
• Stop Motion.........................................................................13
Updating Firmware.....................................................................14
Term Reference Guide ..................................................................14
USER GUIDE

support.kesslercrane.com Page 2 of 14
USER GUIDE
B
A
C
D
E
IJ
F G H
M
KL
THE CONTROLLER
SECOND SHOOTER PRO
Extended Range WiFi Antenna
This isn’t just for style, the external antenna provides a longer operational
range. It is recommended not to block the antenna from the receiving
device for maximum operational range.
Menu Button
Navigate backwards to the previous menu with this button.
Directional Arrows
The directional arrows can be used to navigate through the menu and also
control the Left/Right movement of the Slider motor, Left/Right movement
of the pan motor, and the Up/Down movement of the tilt axis. Press and
hold (for 3 seconds) Left/Right or Up/Down to swap move orientations.
Enter Button
Use this button to select options through the menu.
Shift Button
This button in conjunction with other buttons allows for secondary controls.
Shift+ Directional arrows increases speed during set to allow moves to be
programed faster Shift+ Enter turns the LED Light on/off.
Shift toggles backlight on/off during time lapse move.
Power Port
Connect the supplied AC wall power cord or a 12V DC cable for battery
power.
USB Port
Connect the Controller to a computer via the supplied USB cable to update
rmware.
Two Expansion Ports
Connect to various external accessories such as the Digital Control Center,
while at the same time connecting two controllers together in Bridge Mode.
Wire Clip
Connect the power cord through this clip to prevent unwanted
disconnection.
Lemo 2-Pin Power
This is an alternative, industry-standard power option that is compatible with
many types of batteries and accessories. The system can be powered by
MagPak, MagMax 3A, direct AC power, and other devices that provide Lemo
2-pin power.
LED Light
Press Shift+ Enter to turn off/on.
I/0 Ports
Used to connect external intervalometers and bulb-ramping devices, such as
Ramper Pro.
CAT5 Ports (Slider, Pan, Tilt)
Connect each axis to corresponding port via provided CAT5 cable.
A
B
C
D
E
F
G
H
I
J
K
L
M

support.kesslercrane.com Page 3 of 14
USER GUIDE
SMALL PULLEY
To remove the pulley installed on the Slider motor, simply pull outward away from the motor.
To install the pulley, simply push the pulley onto the motor shaft while aligning the holes. Be
sure to hold the belt in place while installing.
PULLEY STORAGE PIN
LARGE PULLEY
GETTING STARTED
SECOND SHOOTER PRO
HARDWARE SET-UP
Slider Motor
Choose your desired motor speed by arranging the proper combination of motor pulleys. The
metal pin on the Slider motor is to be used for storing the extra pulley.
1.
2.
3.

support.kesslercrane.com Page 4 of 14
USER GUIDE
Choose between the following pulley combinations: Fast, Normal and Slow.
FAST (LOW TORQUE)
*This combination is only compatible with CineSlider, Philip Bloom and Stealth sliders.
Install the Small Pulley onto the Slider Motor.
The pre-installed belt (labled 110XL) on the Slider Motor is to be used in most
applications. However, if using the Small Pulley in conjunction with the Shuttle Pod, Shuttle
Pod Mini, Shuttle Dolly or Pocket Dolly v2.0 follow steps 5-6.
Place the smaller belt (labled 100XL) around the Small Pulley.
Mount the Slider Motor onto the Motor Mount utilizing the threaded holes nearest to the
pulley on the back side of the motor.
4.
5.
6.
7.
GETTING STARTED
SECOND SHOOTER PRO

support.kesslercrane.com Page 5 of 14
USER GUIDE
NORMAL
SLOW (HIGH TORQUE)
Mount Slider motor to slider using a Kessler Motor Mount.
Connect CAT5 cable from Slider motor to the SLIDER port on the Controller.
*This combination requires the pulley from the Motor Mount Kit to be used on the slider.
8.
9.
GETTING STARTED
SECOND SHOOTER PRO

support.kesslercrane.com Page 6 of 14
USER GUIDE
2.
4. Plug in power supply.
INTERVALOMETER CONNECT
For time lapse or stop motion, connect a Camera Control Cable to the out port on the
controller to the camera.
PAN & TILT AXIS
Mount your Pan & Tilt head utilizing the 3/8”-16 and ¼” – 20 holes on the underside of the
Head. (Recommended Mounting: Kessler Kwik Release + 3/8”-16 Kwik Short Plate)
Connect CAT5 cable from the side of the Pan base to the PAN port on the controller.
Connect CAT5 cable from the Tilt axis to the TILT port on the controller.
1.
1.
3.
GETTING STARTED
SECOND SHOOTER PRO

support.kesslercrane.com Page 7 of 14
USER GUIDE
To use the Second Shooter Pro controller with kOS software, you will need kOS for
Second Shooter v4.5 or greater for Mac, Windows or iPad. The Second Shooter Pro is not
compatible with kOS software versions prior to v4.5.
CONNECTING TO KOS VIA USB
Connect USB/Micro USB cable to computer and Second Shooter Pro controller.
Open kOS and click connect. Your Second Shooter Pro will automatically connect to kOS.
CONNECTING TO KOS VIA WIFI
Press the Menu button until the main version screen is displayed. Once the version is
displayed, the Operation Mode menu will display.
If the WiFi menu option reads “WiFi Enabled”, the Wi access point is active. Proceed to #4.
If the WiFi menu option reads “WiFi Disabled”, select it and press the Enter button, your
Second Shooter Pro will reboot and will now say “WiFi Enabled”.
On your computer or tablet you will now see a WiFi network named “2ndShooter+”. Connect
to that wireless network.
Once connected to the “2ndShooter+” network, open kOS and it will automatically connect
to your Second Shooter Pro via WiFi.
2.
3.
4.
5.
1.
USING KOS
SECOND SHOOTER PRO

support.kesslercrane.com Page 8 of 14
USER GUIDE REMOTE APP
SECOND SHOOTER PRO
PAIRING THE SECOND SHOOTER REMOTE APP
Go to your iPhone settings>Wi> and select Second Shooter Pro. Return to the Second
Shooter Remote app and the connection should automatically be made. For further support
and troubleshooting, see Second Shooter Remote manual.
Pairing the PS4 controller to Second Shooter Remote app
Hold down the PS button and the Share button simultaneously for 5 seconds, or until
the lights ash. Open your iPhone settings, go to Bluetooth, and select DUALSHOCK 4
Wireless Controller from the list of new devices. Once connected, open the Second Shooter
Remote app and click the Controller icon to pair. For further instructions, support, and
troubleshooting, see Second Shooter Remote manual.

support.kesslercrane.com Page 9 of 14
USER GUIDE BRIDGE MODE
SECOND SHOOTER PRO
By utilizing one of the available expansion ports, users can link two Second Shooter Pro
controllers or a Second Shooter Pro and rst generation Second Shooter controller to have
6-axes available simultaneously.
In order to get started with Bridge Mode, users will need to connect each of the controllers
with a Bridge Cable.*
In addition to the Second Shooter Pro’ Expansion Port being used to connect to controllers
in Bridge Mode, it can also be utilized to connect to motion control accessories, such as the
Digital Control Center.
SETTING UP BRIDGE MODE
Plug in the Bridge Cable* into one of the expansion ports on the bottom of each controller,
and connect your motors to the CAT5 ports on the top of the controllers.
Once the controllers are powered on, in the OPERATING MODE menu indicate if the controller
is going to be a master or slave unit. (If bridging a Second Shooter Pro and rst generation
Second Shooter Controller you will want to set the Second Shooter Pro controller as the
master unit.)
You can now program a move or do a manual move like normal.
When (Master Active) is shown on the Master controller the arrow buttons on each
controller will control the motors connected to that controller.
To be able to control the motors connected to the slave unit through the master unit double
tap shift. The controller will now show (Slave Active) and pressing the arrow buttons on the
master unit will control the motors connected to the slave unit.
*Although these cables are similar to other RJ-11 cables, DO NOT use any other cable for bridging Second
Shooter Controllers. Doing so may put your system at risk for damage.
2.
3.
1.

support.kesslercrane.com Page 10 of 14
USER GUIDE SETTING UP A MOVE
SECOND SHOOTER PRO
After powering up the system you will be presented with four options:
• PROGRAM MOVE
• MANUAL MOVE
• TURNTABLE
• SETTINGS
SETTINGS
• Operation Mode – Standalone, Master/Slave, WiFi settings, Quiet Mode settings.
• Control Options – Inverts Controls depending on user preference.
• Firmware Update – See “Updating Firmware” section.
• Lash Compensation*– Set up a pre-move to remove any lash in the system due to a
change in direction.
*Lash Compensation is a unique setting for each pan unit and is set from the factory if the controller and
pan motor are purchased together. If wanting to change these settings, please take note of the factory
setting to be able to reset it. The setting for all other motors should be set to zero.
MANUAL MOVE
Select MANUAL MOVE to do a live move without programming.
The default speed of Manual Move mode is 50%. This selection will be blinking. If you’d like
to adjust that speed up or down you can do so using the Up or Down arrow. Once you’ve
adjusted that to the speed you like, press Enter.
The screen will now display RUNNING which allows you to manually move each axis by
using the directional arrows.
The SET CALIBRATION*feature allows you to focus on the shot rather than worrying
about running your motors into the end of the slider. It works by setting a minimum and
maximum limit range of each axis to avoid collisions and event errors by exceeding the
travel range of each motor.
*Note: When setting your calibration limits, make sure you’ve set your range of every active axis before moving
on to set the second limit range point.
TURNTABLE
Select TURNTABLE for continuous panning.
The speed can be adjusted by pressing the Up or Down arrow at any time.
Press the pan Left or Right arrow to start/stop panning.
2.
3.
1.