Kettler LIFE 1715-205K1 User manual

Assembly Instructions
IMPORTANT
PLEASE KEEP THIS BOOKLET FOR FUTURE REFERENCE.
THIS IS IMPORTANT INFORMATION REGARDING THE USE AND
CARE OF YOUR GARDEN FURNITURE.
Feb 2022
1715-205K1
Casual Dining Table
55" x 30" Adjustable

Do not discard any of the packaging until you have checked
that you have all the parts and the pack of xings.
8.
7. Please do not use substitute parts. Use only additional or replacement parts supplied by Kettler.
In the unlikely event that this product has missing or damaged parts, please visit our
website www.kettlerusa.com/parts or call, 866-804-0440.
Do not use any other tools other than those recommended to build this product.6.
Keep ttings out of children’s reach.5.
be fully tightened.
during initial assembly. Only upon completion of the assembly should all xing points
To ensure an easier assembly, we strongly advise that all ttings are only nger tightened4.
Assemble this product on a soft surface.3.
the pack of ttings.
Do not discard any of the packaging until you have checked that you have all the parts and2.
step by step instructions.
We suggest you spend a short time reading through this leaet and then follow the simple1.
Helpful advice before you begin:
Parts List
A: 1pc - Frame B: 1pc - Leg
Support C: 1pc - Base D: 1pc - Top E: 4pcs - Braces
F: 8pcs -
M8x45mm Bolt G: 8pcs -
M6x20mm Bolt H: 2pcs -
M6x30mm Bolt I: 14pcs -
Rubber Bumpers J: 1pc - Ratchet
L: 1pc -
4mm Allen Bit
K: 1pc -
5mm Allen Bit

2
1
Assembly
B
Flip the clasp and press
it down to release the
gaspump completely
Fasten all the parts

3
Assembly
4
J
L
G
Align the lever with the side of the frame with notch for lever
A
Make sure that both
legs are at the same
height and level
J
L
H

5
Assembly
Finished
6
CFKJ
E
Hand tighten all
bolts before going
back and tightening
them with the ratchet
D
I

2
1
Operation
Press handle A. The table top will go up automatically. You can
stop the table at any desired height.
Press handle A& push down on the top. You can stop the table
at any desired height.
A
A

Parts Request Form
Model # (Required )*
Qty Item # (Optional)
Spare parts do not include mounting hardware. Please specify "with hardware" if needed.
Yes Date of purchase: Place of Purchase:
No CC:
Card type: Card No.: Exp:
(Required)
Ship to:Name:
Attn:
Address:
City: State/Prov:
Country:
Home Phone Number: Fax:
Email:
Billing Address for CC: (If different from above address)
Address:
Zip/Postal Code:
*Model numbers for toys and tennis table products can usually be found on a white sticker about 1 inch in diameter located on the underside of the unit; it
will be the 08xxx-xxx or 07xxx-xxx #. Model number for fitness products can be found on the silver label located on the frame of the unit listed as a TYP #
or ART. NR. Note: If a computer is being ordered for any Ergometer the BAUJAHR or the SERIEN NR. off of the unit MUST be included in the
description; this can also be found on the silver label. If you cannot provide the model # a picture is required for product identification.
Any order placed without the model # supplied will be non - refundable.
Phone - 866.804.0440
Fax - 757.427.0183
Email - [email protected]
Web Site - www.kettlerusa.com
KETTLER International, Inc.
Parts & Service Dept.
1355 London Bridge Rd.
Virginia Beach, VA 23453
Model Name
Unit that parts are being requested for:
P.O./Reference #:
*Serien Nr. or Baujahr
Method of payment: Check:
Parts Description
Is this a warranty parts order?
(Proof of purchase may be required)
Reason for order:
Zip/Postal Code:
We accept Visa, MC, and/or prepaid check/money order only. Part orders are subject to a S&H fee.
Last 3 digits from security code on back of CC:

Notes

Notes

Notes