Keurig B150P User manual

Owner’s manual
B150P Keurig® Brewer
manuel D’uTIlIsaTIOn
Cafetière B150P de Keurig®

32
Removing the serial number label from the Brewer will void warranty.
CAUTION: There are two sharp needles that puncture the K-Cup®
portion pack, one above the K-Cup®Holder and the other in the
bottom of the K-Cup®Holder. To avoid risk of injury, do not put
your fingers in the K-Cup®Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup®Holder
during the brewing process. To avoid risk of injury, do not lift the
Handle or open the K-Cup®Assembly Housing during the brewing
process.
If an extension cord is used, (1) the marked electrical rating of the
cord set or extension cord should be at least as great as the electrical
rating of the appliance; (2) the cord should be arranged so that it will
not drape over the countertop or tabletop where it can be pulled on
by children or tripped over unintentionally; and (3) the extension cord
must include a 3-prong grounding plug.
THIS PRODUCT IS FOR
COMMERCIAL USE
WARNINGTHIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN !
TABLE OF CONTENTS
KEURIG®GOURMET SINGLE CUP BREWING SYSTEM
KEURIG® B150P —Using Your Brewer
SET-UP
Helpful Hints ........................................................................................4
Unpacking ............................................................................................ 4
Features ............................................................................................... 5
Plumbing Instructions........................................................................ 6
SECTION 1—SET-UP & FIRST BREW
Set-Up & First Brew ...........................................................................7
SECTION 2—MENU CONTROLS & INDICATORS
Setting the Clock ...............................................................................12
Programming Brew Temperature .................................................12
Programming Brew Size .................................................................13
Programming On/Off Features ......................................................13
SECTION 3—CLEANING & MAINTENANCE
Cleaning.............................................................................................. 15
De-Scaling.......................................................................................... 16
Storage ...............................................................................................17
SECTION 4—TROUBLESHOOTING..................................................18
SECTION 5 —WARRANTY................................................................ 19
Pour des directives en français, veuillez vous reporter à la page 20.
Record your Brewer Serial Number here.
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic
safety precautions should be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
3. This appliance must be properly installed
and located in accordance with these
instructions before it is used.
4. The use of accessory attachments not rec-
ommended by the appliance manufacturer
may result in fire, electrical shock or injury
to persons.
5. Do not place on or near a hot gas or electric
burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock and
injury do not immerse cords, plugs, or the
appliance in water or any other liquid.
8. Turn off and unplug the Brewer before
cleaning or maintenance.
Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
9. For best operation, plug the appliance
into its own electrical outlet on a dedicated
circuit to prevent flickering of lights, blowing
of fuses or tripping a circuit breaker.
10. Do not operate any appliance with a
damaged cord or plug or after the appliance
malfunctions or is damaged in any manner.
Contact Keurig Customer Service to
report any malfunction of or damage
to the Brewer.
11. Do not let the cord hang over the edge of
the table or counter, or touch hot surfaces.
12. To disconnect, press the Power Button on
the Brewer to ‘OFF’ status and then remove
the plug from the wall outlet.
13. Close supervision is necessary when any
appliance is used by or near children.
14. Do not lift the Handle to open the Lid of
the Brewer while brewing is in progress.
15. This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The appliance must be
grounded using a 3-hole properly grounded
outlet. In the event of an electrical short
circuit, grounding reduces the risk of
electrical shock.
16. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
17. Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord or use an adapter.
18. Consult a qualified electrician if the
grounding instructions are not completely
understood, or if doubt exists as to whether
the appliance is properly grounded.
19. Do not use the appliance for other than
its intended use.
SAVE THESE
INSTRUCTIONS.
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use Brewer
unless there is adult supervision. Brewer
dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS:
IMMEDIATELY AFTER USING A HOT COCOA
K-CUP® PORTION PACK, RUN a Hot Water
Brew Cycle without a portion pack to avoid the
possibility of clogging the exit needle.
DO NOT assume the next user will do this.

Set-up
5
A. Handle
B. Lid
C. LCD Screen
Helpful Hints
1. Keep your Brewer turned “ON” at all times.
To brew a fresh cup of coffee, tea or hot cocoa
anytime you want, we suggest you keep your
Brewer turned “ON” all the time. However, the
Brewer is fully programmable so you can set it
to turn on and off automatically to match your
schedule. Or, if you prefer, set the Brewer to
automatically turn off after a period of time.
Follow the simple instructions on pages 13 –14
to make using the Brewer convenient for you.
2. For the best tasting gourmet coffee, tea or
hot cocoa, Keurig recommends using bottled
water or the Keurig® Water Filter Starter Kit
(available at www.keurig.com).
Water quality varies from place to place. If you
notice an undesirable taste in your cup of
coffee, such as chlorine or other mineral tastes,
we recommend you consider using bottled
water or water from a filtration system.
3. Customize the size, flavor & brew that’s
perfect for you.
With the choice of over 200 varieties of K-Cup®
portion packs and 5 brew sizes (Small Cup-4
oz., Small Mug-6 oz., Medium Mug-8 oz., Large
Mug-10 oz., and Travel Mug-12oz.) your Keurig®
Brewer gives you endless options to custom-
ize the size, flavor and brew that’s perfect for
you. For a strong, intense cup, select an Extra
Bold portion pack (with up to 30% more ground
coffee than regular varieties) and brew the
size that’s right for you. The smaller the brew
size, the more intense flavor in your cup. The
larger the brew size, the less intense flavor in
your cup.
4. Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other
appliances, your Brewer may not function
properly. The Brewer should be operated on its
own circuit, separate from other appliances.
5. Brewing into a travel mug.
To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.
6. De-scale Brewer regularly.
Please see pages 16 and 17 for instructions.
Unpacking Instructions
1. Place Brewer box on a large steady surface
(such as a table or countertop) or on the floor.
Open the box.
2. Remove enclosed literature.
3. Turn the box on its side with the front of the
box facedown.
4. Reach into the box and grasp the foam insert
that contains the Brewer.
5. Carefully pull the foam insert toward you
and out of the box. The Brewer will still be
encased in the polyfoam and be on its side.
6. Remove the top polyfoam packaging material.
7. Carefully lift Brewer off of the bottom polyfoam
and place it upright on a flat, steady surface.
8. Lift plastic bag off of Brewer.
9. Record the serial number for this Brewer on
page 3 of this guide. The serial number can be
found on the side of the Brewer box or on the
bottom of the Brewer.
10. Place the Brewer upright on a flat, steady
surface. Remove tape holding Water Reservoir
in place.
We recommend you save all packing materials in
case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away
from children.
4
M
L
D. K-Cup®Assembly Housing
E. K-Cup®Holder (F and G are
the K-Cup®Holder Assembly)
F. K-Cup®Holder Funnel
G. Drip Tray Plate
H. Drip Tray
I. Drip Tray Base
J. Housing
K. BREW Button
L. Power Switch
M. Power Cord
N. Filter Kit PN #5572
(not included)
O. Omni KQ8 Filter
(not included)
P. Water Inlet Valve
3/4 Hose Connector
(not included)
Q. Drain Hatch and Knob
R. Drain Tubes and Plugs
K
I
R
Q
C
G
E
F
N
O
H
J
B
D
A
P
Features Keurig®— Model B150P Brewer
Keurig®B150P Brewer
Back view with optional
Filter Kit #5572 connected.

SECTION 1 Set-Up & First BrewPlumbing Instructions
Setting Up Your Brewer
1. Remove all pieces of packing tape from the
Brewer and Drip Tray. Remove the clear plastic
film from the LCD Display. Unwrap cord and
plug the Brewer into a grounded outlet.
2. Turn the Brewer on, the Power Switch is
located at the top left hand side of the Brewer
on the back. The Brewer’s LCD Display will
display the power up welcome screen (fig. 1).
3. The Brewer will automatically fill the Internal
Hot Water Tank with water and then the
water will be heated. This will take about
3 minutes. During the heatingperiod,
“HEATING PLEASE WAIT” will be displayed
on the LCD Screen (fig. 2).
IMPORTANT: You cannot use your Keurig®Brewer until it has been
set up for its first use.
NOTE: If Brewer has been exposed to temperatures below freezing,
allow Brewer at least two hours to reach room temperature before
brewing. A frozen or extremely cold Brewer will not operate.
4. Place a 10 oz. mug on the Drip Tray Plate,
then fully raise and lower the Brewer Handle.
The Brew Button will now be illuminated.
Press the Brew Button to start a cleansing
brew. NOTE: A K-Cup®portion pack should not
be used for this sequence.
5. When the cleansing brew is complete, the
Brewer will go into its idle state and will be
ready to brew your first portion pack.
Ready to Brew Your First Cup
1. The LCD Display will be in its idle state (fig. 3).
2. Lift the Handle. The K-Cup®Holder
will open toward you (fig. 4).
3. Select a K-Cup®portion pack.
NOTE: Do not remove the foil lid
or puncture the portion pack.
4.
Place a K-Cup®portion pack
in the K-Cup®Holder (fig. 5).
CAUTION: There are two sharp needles that
puncture the portion pack, one above the K-Cup®
Holder and the other in the bottom of the K-Cup®
Holder. To avoid risk of injury, do not put your
fingers in the K-Cup®Assembly Housing.
fig. 3
fig. 1
6 7
Welcome To The
Keurig B150 Brewing
System Designed
For The K-Cup®
Portion Pack
Español Français 12: 30 PM
Ready
Choose Your
K-Cup®&
Lift Handle
WATER
LEVEL
Español Français
fig. 2
Heating...
Please Wait
fittings are recommended such as High Density
Polypropylene Type.
4. Connect the ‘INLET’ port of the filter assembly
to the local water supply.
5. Connect a long length of tubing to the EXIT Port
of the filter assembly. DO NOT CONNECT TO
THE BREWER YET.
6. The filter needs an initial flush to clear any
carbon deposits. Route the long length of
tubing from the EXIT port to a container or sink.
7. Turn on water supply and allow at least
4 gallons of water to flush through the filter.
8. Turn off water supply.
9. Cut the tubing to proper length
and connect to inlet plumbing
port on the Brewer by using
water inlet valve 3/4 hose
connector (not included).
10. Turn on water supply.
CAUTION: This Brewer is designed to handle local water pressures
from 40 psig up to 125 psig. Consult a licensed plumber for water
pressures in your area. Use plumbing fittings and tubing specified to
withstand 125 psig.
WARNING: Keurig requires the use of an external water filter such as
the Omnipure KQ8, available from Keurig, Inc. Part No. 5572. Failure
to use a filter invalidates the Brewer warranty.
Plumbing Fitting Connections
1. An external filter (KQ8) can be mounted on the
rear surface of the Brewer using the mounting
screws provided. See back view of
Brewer on page 5.
2. Loosen the two mounting screws located on
the upper-rear of the Brewer and hang the
KQ8 filter kit assembly.
3. Tighten the two mounting screws (be careful
not to over tighten).
NOTE: The KQ8A Filter assembly comes with
1/4 FPT ports for both inlet and outlet and the
plumbed water inlet to the Brewer is 3/4 Male
Garden Hose Thread (Invensys solenoid valve).
1/4 OD LLDPE (Linear Low Density Polyethylene)
tubing is recommended (NSF compliant between
the filter assembly and the Brewer. NSF compliant
connect to
water supply

Purging the Brewer
If your Brewer has not been used for more than
one week, you should purge the water from the
internal water tank.
1. Follow Draining the Brewer instructions
on page 17.
2. Once drained, re-connect Brewer to power
source and turn on.
3. When the Brewer indicates “READY”, place
a large mug on the Drip Tray and select
Large Mug (10 oz. serving) brew size from
the Select Brew Size Menu (fig.8).
4. Discard water.
5. Repeat steps 2 - 4 two more times to
completely purge water from the Internal
Hot Water Tank.
9
Adding Water
Your Brewer has been configured at the factory to be direct plumbed,
however, the Brewer can also be converted into a pour over model
with a Cold Water Tank Spare Part. To order, please call 1.888.CUP.
BREW.
Brewing Hot Water
Your Brewer is able to produce hot water for
making hot cocoa from a packet, or for use in
cooking, etc. Simply follow the instructions on
page 7, “Ready To Brew Your First Cup” without
adding a K-Cup®portion pack.
NOTE: After brewing a hot cocoa portion pack, we
recommend running a hot water brew cycle
without a portion pack.
SECTION 1 Set-Up & First Brew (continued)
8
10. Enjoy your first cup of Keurig Brewed®
gourmet coffee, tea or hot cocoa!
11. Your Brewer may display “HEATING
PLEASE WAIT” as it heats water for
the next brew cycle.
Stopping the Brew Process
If you need to stop the brewing after the process has started, press and
release the Power Switch to turn the Brewer ‘OFF’. The flow of coffee, tea or
hot cocoa will stop and the heating element and the LCD Screen will shut off.
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next
brew. We recommend that you perform a cleansing brew with water only after
a terminated brew. Then your next brew will be the volume you have selected.
5. Lower the Handle to close the Lid over the
K-Cup®Holder. (When it is closed completely,
the BREW Button will flash up to 60 seconds.)
6. Place a mug on the drip tray and select
your brew size (fig. 6), then press BREW (fig. 7).
NOTE: If you do not press BREW within 60
seconds the Brewer will return to its idle state
and the Brew Button will cease to flash to prevent
accidental activation. Re-activate by raising the
handle fully and then closing it.
7. There may be a short pause prior to coffee
being dispensed. The entire brew process
lasts for approximately 1 minute and ends with
a burst of air to remove all liquid from
the portion pack.
CAUTION: There is extremely hot water in the
K-Cup®Holder during the brew process.
To avoid risk of injury, do not lift the Handle
or open the K-Cup®Assembly Housing during
the brew process.
8. The end of brew is indicated by “KEURIG
BREWED ENJOY”.
9. Lift the Handle, remove and dispose
of the used K-Cup®portion pack.
CAUTION: Portion pack will be hot.
fig. 5
fig. 4fig. 6
fig. 7
Select
Brew Size
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.
fig.8
Select
Brew Size
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.

Menu Mode
To enter the MENU MODE the Brewer should be plugged in and the
power must be off. Press and hold your finger on the display while
pressing and releasing the power switch. Continue pressure on the
display for 5 seconds (fig. 9). The MENU screen will appear. (fig.10).
Press any line item to enter the set up for that particular feature.
Please reference the Menu navigation on page 11.
If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.888.CUP.BREW (287.2739).
10 11
Home
Auto OFF
Brew Temp
Language
Clock
ON/OFF Time
Brew Size(s)
Contact
5 seconds.
SECTION 2 Menu Controls & Indicators
Home
Auto OFF
Brew Temp
Language
Clock
ON/OFF Time
Brew Size(s)
Contact
fig. 9
fig. 10
Menu Key Navigation
Home
Press HOME at any time to return to your Brewer to an idle state.
Clock
Setting the clock is optional. To program the clock, follow the
instructions on page 12.
Brew Temp
The brew temperature is pre-set at 193˚F. You do not have to set
the brew temperature but you can adjust it up or down by 5˚.
Simply follow the instructions on page 12.
Brew Size(s)
Five brew sizes are available: 4 oz., 6 oz., 8 oz., 10 oz., and 12 oz.
To program the brew sizes see page 13.
Auto OFF
Auto Off allows you to program your Brewer to automatically turn off two
hours after the last brew. See page 14 for programming instructions.
ON/OFF Time
You can leave your Brewer on all the time and use the Power button to
turn it off. Or you can program the Brewer to brew at a specific time as
shown on page 13.
Language
This Brewer is shipped with English as the default language.
To change the language, follow the instructions on page 14.
Contact
The contact setting features allows you to program the contact
information you need for Brewer support and help. To program,
follow the instructions on page 14.

12 13
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the
LCD Control Center. NOTE: You must set the clock if you will be programming
the Auto On/Off Time feature.
1. From the Menu Mode, press “CLOCK”.
2. The set clock screen will display
“DISABLED” if the Brewer is new or if
electrical power has been interrupted.
Press “DISABLED” to set a time. Press H
repeatedly to advance the hour in steps or
hold it down to scroll through the hours
quickly. When you have set the hour then
press the M to set the minutes, press
repeatedly to advance by a minute each time
or keep it pressed to scroll quickly (fig.11).
3. Press “OK” when you are finished.
The Clock is now set.
4. The correct time should now be displayed in
the LCD Home Screen.
fig.11
Programming Brew Temperature (188°–198º F)
The Brewer brews at a preset temperature of 193°F. You can adjust this
temperature up or down by 5°. Simply follow the instructions below.
1. From the Menu Mode, press “BREW TEMP”.
2. The LCD Display will now display the Brew
Temperature programming options (fig.12).
The temperature 193°F (initial setting) will
be displayed at the top of the LCD Display
to indicate the current temperature setting.
3. Press the + symbol to increase the tempera-
ture and the – symbol to lower the tempera-
ture one degree at a time.
4. Once you have reached your desired brew
temperature, press “OK”. The Brew Tempera-
ture is now set.
5. To change the brew temperature, repeat
steps 1 through 4.
NOTE: At high altitudes (over 5,000 feet)
if boiling occurs, use the temperature
adjustment (-5°) to lower the temperature.
Programming Your Brew Size
All brew sizes are enabled in the default setting. If you want to disable any
brew size, just press on the appropriate icon(s). Please follow instructions
outlined below.
1. From the Menu Mode, press
“SET BREW SIZE(S)”.
2. The LCD will display all enabled brew sizes.
To disable a brew size press the icon. The
check mark will change to an “X” indicating
that the brew size is disabled (fig.13).
3. Once you have selected your desired brew
size(s), press “OK”. The brew size(s) are now
set.
NOTE: You can not delete all brew sizes.
To enable a brew size you have already
disabled, just press its icon and then
press “OK”. The default brew size is
always 8 oz. This brew size cannot be
changed or disabled.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule.
1. Leave it ON all the time. The Brewer can be left
on all the time so that it is always ready to
brew a fresh cup of gourmet coffee, tea or hot
cocoa. To turn the Brewer off at any time,
simply press and release the Power Switch.
Press and release the Power Switch again to
restore power to the Brewer. You will have to
wait for the water to heat up before the Brewer
is ready to brew.
2. Program the Brewer for a specific On/Off
Time. NOTE: To use this programming feature,
the clock must be set to the correct time.
Clock
12:00 AM
OK
MH
193°F
+-
Temperature
OK
fig.14 fig.12 fig.13
NOTE: If power is interrupted to the Brewer, follow the procedure above to
reset the time as the clock will not be visible . Brew size and brew tempera-
ture menu settings will be restored automatically. All other settings will be
restored automatically after clock is set.
NOTE: To disable the clock, press the time. However, the ‘On/Off’ time setting
will also be disabled.
fig.14
a. After setting the correct time (see “Setting The Clock” page 12), return to
the Menu Mode and press “ON/OFF TIME”.
b. To set the ON time, press “DISABLED”. The display will change to a time of
day. Press “H” to set the hours and “M” to set the minutes. Once the
desired time is set, press “OK” to accept this time.
c . To set the OFF time, press “DISABLED”. The display will change to a time
of day. Press “H” to set the hours and “M” to set the minutes. Once the
desired time is set, press “OK” to accept this time (fig.14).
SECTION 2 Menu Controls & Indicators (continued)
ON/OFF Time
ON 12:00 AM
OFF 12:00 PM
OK
MH
MH
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.
OK
3
3
3
3

15
b. Press “OK” to save your changes and
return to the Main Contact Screen.
NOTE: Pressing the Back Arrow Key will
return to the Main Contact Screen without
saving changes.
3. Press the Middle (Phone Number) Box. The
Numeral Keypad Mode will appear along
with the current information (fig.19).
a. Delete current phone number and enter
new information using the Keypad.
b. Press “OK” to save your changes and
return to the Main Contact Screen.
4. Press the Lower Box. This box can be
customized to contain any information
such as web/email address, contact
name, etc (fig.20).
a. Enter new information using the Keypad.
b. Press “OK” to save your changes and
return to the Main Contact Screen.
c. In Main Contact Screen (fig.17), press “OK”
to save the updated screen as the default
and return to the Menu Screen.
SECTION 2 Menu Controls & Indicators (continued)
14
Setting Contact Screen
The contact screen is pre-programmed with
the following information: Keurig, Inc. and
www.keurig.com.
You can reprogram the Brewer with your contact
information. The contact screen will appear in
the screen saver.
1. From the Menu Mode, press “CONTACT”.
The LCD screen will display the Keurig
default contact information (fig.17).
2. Press the Upper (Company Name) Box. The
Keypad will appear along with the current
information (fig.18). NOTE: Unless changed by
the user, Keurig contact information will be
present on the display.
a. Press Delete Key repeatedly to remove
current information. Enter new information
using the Keypad.
NOTE: To select Upper Case, Lower Case,
Numerals, Upper Case Accents, Lower Case
Accents, press the Keypad Change Key located at
the bottom center of the screen.
fig.17 fig.19
SECTION 3 Cleaning & Maintenance
Cleaning External Parts
Regular cleaning of the Brewer’s external components is recommended.
1. Never immerse the Brewer in water or other liquids. The Housing
and other external components may be cleaned with a soapy, damp,
non-abrasive cloth.
2. The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray
and Drip Tray Plate should be periodically inspected and rinsed clean.
To remove the Drip Tray Assembly, simply slide it toward you, keeping it
level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should
not be placed in the dishwasher. They should be cleaned with a damp,
soapy, non-abrasive cloth and rinsed thoroughly.
Cleaning the K-Cup®
Holder Assembly
1. Cleaning the Parts—The K-Cup®Holder
Assembly can be placed onto the top shelf of
a dishwasher. NOTE: Use low temperature
cycles in the dishwasher. To remove the
K-Cup®Holder Assembly from the Brewer,
open the cover by lifting the Handle. Grasp
the top of the K-Cup®Holder with one hand
while pushing up on the bottom of the
K-Cup®Holder from underneath with the
other until it releases (fig.21). After cleaning,
align the K-Cup®Holder with the opening
fig.21
fig.18 fig.16 fig.20
WWW.KEURIG.COM
PHONE #
KEURIG,
INCORPORATED
Contact
OK
Language
Español
English
Français
OK
3. Set the Brewer to “AUTO OFF” to automatically
turn off 2 hours after the last brew.
a. From the Menu Mode, press “AUTO OFF”.
The LCD Display will now display the
“AUTO OFF” programming option (fig.15).
b. To enable the “AUTO OFF” feature, press “ON”.
“ENABLED” will appear on the screen and
press “OK”. To disable the “AUTO OFF” feature,
press “OFF”. “DISABLED” will appear on the
screen and press “OK”.
Language Settings
The Brewer is shipped with English as the default
language. To change the default to Francais or
Espanol, follow the instructions outlined below.
Set Language
1. From the Menu Mode, press “LANGUAGE”.
2. The LCD Display will now display the
Language programming options (fig.16).
3. Press the desired Language button, then
press OK to confirm your selection.
fig.15
Auto OFF
Auto Off 2 hours
After Last Brew
OK
OFFON
21 3
456
789
Delete 0Space
PHONE #
OK
ABC
abc
123
ABC DEF
GHI JKL MNO
PQR S TU V WX YZ
Delete . , - Space
KEURIG,
INCORPORATED
OK
ABC
abc
123
ABC DEF
GHI JKL MNO
PQR S TU V WX YZ
Delete . , - Space
WWW.KEURIG.COM
OK
ABC
abc
123

16
using the two front ribs as a guide, and snap
them into place from the top.
2. Cleaning the Funnel —The Funnel can be
removed from the K-Cup®Holder by pulling
on it until it pops off (fig. 22). The Funnel is
dishwasher safe. To replace it, just snap it
back onto the K-Cup®Holder.
3. Cleaning the Exit Needle—The Exit Needle
is located on the inside bottom of the K-Cup®
Holder. Should a clog arise due to coffee
grinds, it can be cleaned using a paper clip
or similar tool. Remove the K-Cup®Holder
Assembly and detach Funnel. Insert the
paper clip (as shown in fig. 22) into the
Needle to loosen the clog, then flush
with water. The K-Cup®Holder Assembly can
be placed onto the top shelf of a dishwasher.
NOTE: Use low temperature cycles in the
dishwasher.
CAUTION: There are sharp needles that puncture the portion pack, one above
the K-Cup®Holder and in the bottom of the K-Cup®Holder. To avoid risk of
injury, do not put your fingers in the K-Cup®Assembly Housing.
SECTION 3 Cleaning & Maintenance (continued)
!
fig.22 De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the mineral
content of the water in your area, calcium deposits or scale may build up in
your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer
performance. De-scaling your Brewer helps maintain the heating element
and other internal parts of the Brewer that come in contact with water.
The Brewer should be de-scaled every 3-6 months using to ensure optimal
performance. It is possible for calcium deposits to build up faster, making it
necessary to de-scale more often. The Symptoms of scale build up are slow
brewing and/or short cups.
The following procedure outlines the steps required to prepare the Brewer
for the addition of the commercial citric acid Descale Solution (PN # 5026)
available from Keurig, Inc.
1. Unplug the Brewer from the power supply.
2. Disconnect or interrupt the external water supply feeding the Brewer.
3. Drain the Hot Water and Cold Water Tanks (see Draining the Brewer
instructions on page 17).
4. Remove the two screws located on the back, top, left of the Brewer.
Remove the Top Cover to gain access to the internal Cold Water Tank and
expose the Descaling Solution Access Port.
5. Reconnect the power supply.
6. Proceed with the descaling procedure on page 17.
De-Scaling Instructions
A. PREPARE
Step 1: Prepare at least 40 oz. of commercial citric acid Descale Solution.
You will also need a large ceramic mug (do not use a paper cup)
and access to a sink for discarding hot liquid.
B. FILL AND CLEAN
Step 1: Pour 40 oz. of Descale Solution into the Cold Water Tank through the
Access Port. Turn on the Brewer – the Brewer will automatically fill
and begin heating.
Step 2: When the LCD displays “Ready,” place a large mug on the Drip Tray,
select the largest brew volume, and press the BREW Button. DO NOT
USE A K-CUP®PORTION PACK. Once the solution begins to exit the
Brewer, lift the Handle just enough to halt the brew process. Let the
Brewer sit for 40 minutes.
Step 3: At the end of 40 minutes, lower the Handle. The Brewer should
complete the brew (do not be concerned if the Brewer does not
complete the brew). Pour the dispensed liquid into the sink.
Step 4: Turn off the Brewer, unplug it, and drain Hot Water and Cold Water
Tanks using the Drain Tubes on back of Brewer.
C. RINSE
Step 1: Manually fill the Cold Water Tank with 40 oz. of fresh water
and drain. Repeat 2 more times.
Step 2: Reconnect the water supply, power supply and turn on the Brewer.
Step 3: Conduct a hot water brew cycle (see page 9) and discard hot water
brew into the sink. Repeat until all Descale Solution is no longer
evident. Remember to open and close the Brewer Handle between
each hot water brew cycle.
Service
Beyond these recommended cleaning and maintenance procedures this
Brewer is not user serviceable. For service, please refer to the Warranty
section of this guide.
Storage
Draining the Brewer
1. Turn off the Brewer, unplug it, and allow the Brewer to cool for 30 minutes.
2. Turn the Brewer around so the back is facing out. Unscrew the small knob
to release the back panel, remove the panel from the Brewer, and set it
aside. If the screw is tight, you may need to use a flathead screw driver.
Pull the tube downward until the end is free (fig. 23). Over a large pitcher,
remove the plug and drain the water from
the Internal Hot Water Tank into the pitcher.
CAUTION: If the Brewer was not allowed to
cool sufficiently, the water draining from the
tube may be very hot. Re-cap the tube.
NOTE: To avoid losing parts, when finished,
re-insert the tube and screw the panel back
onto the Brewer.
fig.23
17

SECTION 5 Warranty
Limited One Year Warranty
Keurig Incorporated warrants that your Brewer will be free of defects in
materials or workmanship under normal use for one year from the date of
purchase. It is recommended that you fill out and return the warranty card
enclosed with your Brewer so that your purchase information will be stored
in our system. Keurig will, at its option, repair or replace the Brewer without
charge upon its receipt of proof of the date of purchase. If a replacement
Brewer is necessary to service this warranty, the replacement Brewer may
be new or reconditioned. If a replacement Brewer is sent, a new limited one
year warranty will be applied to the replacement Brewer.
This warranty only applies to Brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
Nor does this warranty cover damages caused by services performed by
anyone other than Keurig or its authorized service providers, use of parts
other than genuine Keurig parts, or external causes such as abuse, misuse,
inappropriate power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR B150P BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANT ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Some states or provinces do not allow disclaimers of such implied
warranties or limitations on how long an implied warranty lasts, so
the above limitation may not apply to you depending on the state or the
province of purchase.
How do you obtain warranty service?
Keurig®Brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.888.CUP.BREW (287.2739). Please do not return
your Brewer for servicing without first speaking to Keurig Customer Service
to obtain an Authorization to Return number (ATR). Keurig®Brewers returned
without an ATR number will be returned to the sender without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.888.CUP.BREW (287.2739)
1918
If any problems persist, contact Customer Service at 1.888.CUP.BREW (287.2739)
SECTION 4 Troubleshooting
Situation
Brewer does not
have power
Brewer will
not brew
Solution
•Plug Brewer into an independent outlet.
•Check to be sure that it is plugged in securely.
•Plug into a different outlet.
•Reset your circuit breaker if necessary.
•Make sure that the Power Switch has been turned on
and LCD Display is illuminated.
•After placing the K-Cup®portion pack in the K-Cup®
Holder, make sure the Handle is pushed down securely
and the LCD Control Center reads “READY TO BREW”
with the BREW Button flashing, then press the Left,
Right or BREW Button.
•The Exit Needle may be clogged (refer to page 16).
LCD Messages
• In plumbed mode, if the water flow has been interrupted,
LCD Screen will instruct you to “Please Press Brew
Button” then “Heating, Please Wait”. Follow these
instructions.
• If the messages persist after following these
instructions, contact Customer Service at
1.888.CUP.BREW (287.2739).
Situation
Chlorine or mineral
taste in coffee
Brewing a partial cup
The time is not
displayed on the LCD
Message Center
Brewer shuts
off or turns on
automatically
Solution
•Consider using bottled water or filtered water. If you
have any questions, contact Customer Service at
1.888.CUP.BREW (287.2739).
•The Exit Needle may be clogged (refer to page 16).
•Clean the K-Cup®Holder Assembly if necessary
and rinse under faucet (refer to pages 15-16).
•“De-Scale” the Brewer (refer to pages 16-17 ).
•If you have repeated the de-scale procedure on
your Brewer two times and it is still only brewing
a partial cup, contact Customer Service at
1.888.CUP.BREW (287.2739).
•The time will not be displayed on the LCD
unless you have set it. To set the clock, follow the
procedure on page 12.
•If power is interrupted to the Brewer, you will
need to set the clock again using the procedure
on page 12.
•Check to make sure that the Auto Off timer
and/or On/Off time features have not been set. To
do this, press the MENU Button below “MENU”
and scroll through the programming options.
“OFF” should be displayed for Auto Off timer and
On/Off. If “OFF” is not displayed, follow
directions on pages 13-14 to reset.