Keurig K150 Manual

1
K150/ K150P CLEANING & START-UP PROCEDURE
This procedure demonstrates how to properly
clean and sanitize the Keurig® K150/ K150P brewer
This procedure should take approximately 30 minutes
Tools Needed
 Clean & Sanitize Kit (if available)
 Available sink

2
Cleaning
Carefully unplug brewer and bring to sink
Fig. 1
For K150 remove Reservoir and drain (see Fig. 1)
For K150P turn water OFF and disconnect water line (see Fig. 2)
Fig. 2

3
Cleaning cont.
Fig. 3
Fig. 4
Lift handle and remove any used K-Cup® pods that may be present (see Fig. 3)
Remove rear Door Hatch and locate drain tubes at rear of brewer and carefully drain (see Fig. 4)
CAUTION
WATER MAY BE VERY HOT

4
Cleaning cont.
Remove all parts as shown below (see Fig. 5)
Clean and sanitize thoroughly per Clean & Sanitizing procedure (see pg. 5)
Follow up with wipes on all exterior of brewer
Fig. 5
CAUTION
Sharp Needle

5
Cleaning Solution
1. Prepare Urnex Rinza solution by adding 8 oz (240 ml) of Urnex Rinza concentrate to 1 gallon (3.5 L)
of warm tap water (or equivalent dilution)
2. Mix well and use immediately
3. Soak removed parts for 30 minutes in solution
Note: If parts could not be removed from the appliance, then add c leaning solution to a soft cloth and use it to coat appli-
ance
parts then let sit for 30 minutes
Note: If Sanitize step is not performed, Rinse parts thoroughly to remove Rinza completely for surfaces.
Sanitizing solution
1. Prepare Urnex Complete Café Sanitizer Solution by adding 0.5 oz (15 mL) of Urnex Complete Café
concentrate to 1 gallon (3.7 L) of warm tap water
2. Mix well and use immediately
3. Soak parts in solution for 1 minute
If parts could not be removed from the appliance, then add sanitizing solution to a soft cloth and use it to coat appliance
parts then let sit for 1 minute
4. Remove parts from solution and allow to drain and dry completely
Do NOT rinse
If parts were not removed from the appliance, wipe with a clean soft cloth and let air dry
Do NOT rinse or apply water
Sanitize Machine Surfaces (as needed)
1. Prepare a solution of 4 mL of Urnex Complete Café Sanitizer to 1 L of water in a spray bottle
2. Spray exterior surface of appliance and allow solution to remain on surface for 1 minute
3. Wipe away with clean cloth and allow to fully air dry
Urnex Café Wipz
These can be used to wipe down any components of the brewer that cannot be easily removed
Urnex Cleaning Pods
These can be used during Cleansing brews to clean the bottom of the pod holder and exit needle
Cleaning & Sanitizing Procedure

6
Running a Cleansing Brew
Reassemble all parts removed ensuring that the Removable Float (item Q) is installed correctly
K150: fill Reservoir with fresh water (see Fig. 6)
K150P: reconnect water line and turn valve ON (see Fig. 7)
(CHECK FOR LEAKS)
Fig. 6
Fig. 7
Plug brewer into a grounded outlet and press Power Switch (item O)
Located at top left hand side at rear of brewer
The brewer’s LCD Display will display the power up welcome screen (see Fig. 6)
Fig. 6

7
Running a Cleansing Brew cont.
Please wait until the water reaches the correct temperature (less than three minutes)
(see Fig. 7)
Fig. 7
The LCD Display will change & notify when ready (see Fig. 8)
Fig. 8

8
PROCEDURE COMPLETE!
If you have any questions please contact Keurig Commercial Technical Support: 888-287-2739 option 5
Running a Cleansing Brew cont.
Open and close Handle
Do NOT insert a K-Cup® pod
Select the 10oz Brew Size
Press the BREW button
Pour HOT water into sink
NOTE: If available, an Urnex cleaning cup can be used for one of the Cleansing Brew cycles
*Repeat Cleansing Brew 3 times*