Keurig K-Slim + ICED User manual

Get the most from your
new Keurig®brewer
Use & Care Guide
Slim®
+ICED™

BREW
OVER
ICE
Remove pcking tpe from brewer.
Plug into  grounded outlet. Plce
mug on drip try.
NOTE: The brewer will automatically turn off after
5 minutes of inactivity. Or, you can hold down the
BREW OVER ICE button to turn the brewer off
at any time.
Remove the water reservoir lid,
then lift the reservoir straight up
to remove it.
Rinse reservoir with fresh water
and fill to the MAX FILL line.
Replace water reservoir, making
sure the lock tabs engage with the
brewer. Replace lid.
NOTE: Do not use distilled water.
Lift and lower the handle. Do not
insert a K-Cup® pod. The brewer will
power on automatically.
The 3 cup sizes will blink. Press
the 8oz button, then press the
blinking BREW button to start
a cleansing brew. Pour the hot
water into the sink.
The one-time setup process is
now complete and you are ready
to brew!
1
3
5 6
2
4
Before You Brew


















BREW
BUTTON
1
Plug & Place Rinse & Fill
Lift & Lower Cleansing Brew
Brew Your First Cup
STRONG
STRONG
The three brew size buttons will blink.
Select your brew size, then press the
blinking BREW button. The BREW
button will remain illuminated while
brewing. Brewing is complete when
the buttons are no longer illuminated.
Lift the handle and dispose of the
K-Cup® pod.
The BREW OVER ICE button will blink.
Select BREW OVER ICE button, then
press the blinking BREW button. The
BREW button will remain illuminated
while brewing. Brewing is complete
when 6oz has been dispensed and the
buttons are no longer illuminated. Lift
the handle and dispose of the K-Cup®
pod.
Place a mug on the drip tray. If
using a travel mug, remove the drip
tray and place the mug on the drip
tray base. Lift the handle and place
a K-Cup® pod in the K-Cup® pod
holder. Lower the handle completely
to close the lid.
Do not remove the foil lid on the
K-Cup® pod.


















BREW
BUTTON


















BREW
BUTTON
BREW
OVER
ICE
Brew & Enjoy!Place Mug & Pod
CAUTION: While brewing, there is extremely hot water in the K-Cup® pod holder. To avoid injury, do not lift the handle
during the brewing process.
NOTE: For best results, we recommend one time use with our K-Cup® pods. A twice-brewed pod won’t provide full flavor
and if the pod holder isn’t lined up with the original holes it can cause an overflow of water and coffee grounds.
HOT
OR
BREW OVER ICE

The water reservoir should be
cleaned periodically by wiping the
inside of the reservoir and underside
of the lid with a damp, non-abrasive,
lint free cloth. Do not dry the inside
of the water reservoir with a cloth as
lint may remain. Allow the reservoir
to dry completely.
Brewer Exterior
Keep your Keurig® brewer looking its
best by cleaning the exterior from
time to time. Just clean with a damp,
soapy, lint-free, non-abrasive cloth.
Never immerse the brewer in water or
other liquids.
Drip Tray
The drip tray can hold up to 8 ounces
of overflow and should be emptied
and cleaned occasionally. To remove,
slide it toward you, keeping it level to
avoid spilling. Rinse and clean with a
damp, soapy, lint-free, non-abrasive
cloth.
Water Reservoir
Brewer Features
BREW OVER ICE: For iced beverages fill a large plastic tumbler with
ice (do not use glass). Insert any K-Cup® pod, then press the BREW
OVER ICE button, followed by BREW button. A 6oz beverage will
be dispensed that starts brewing hotter to help extract full flavor, then
cools down for less ice melt and a vibrant balanced flavor.
FAST & FRESH-BREWED: Coffee made in minutes.
BACK-TO-BACK BREWING: Immediately brew a second cup, no need to
wait for reheating.
TRAVEL MUG FRIENDLY: Accommodates travel mugs up to 7” tall.
MAINTENANCE ALERT: Reminds you to descale after every 250 brews.
AUTO OFF: Automatically turns your brewer off 5 minutes after the last
brew for energy savings.
HIGH ALTITUDE: To ensure your brewer works properly at higher
altitudes (5,000 feet), enable the High Altitude setting by pressing and
holding the BREW button and 8oz buttons for 3 seconds.
Caring For Your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Regular Maintenance
For great-tasting coffee, keep your brewer running at peak
performance by following the recommended maintenance
schedule:
*To turn off Descale notification, follow the full descaling procedure as outlined
in the Use & Care Guide
Safe and effective-helps remove
residue and oils from your coffee
maker’s needles and pod holder
Keurig®Rinse PodsWeekly
Every 2 Months
Every 3 Months or when
the Descale notification
turns on*
Keurig®Water Filters
Keurig®Descale Solutions Helps eliminate mineral build
up to preserve the long-term
health of your coffee maker
Change your water filter every two
months to help remove impurities
from water for great tasting coffee
BenefitProductFrequency

K-Cup® Pod Holder
To remove the K-Cup® pod holder from
the brewer, lift the handle and grasp
the top of the K-Cup® pod holder
with one hand while pushing up on
the bottom of the K-Cup® pod holder
from underneath with the other until
it releases. After cleaning, align the
K-Cup® pod holder with the opening
using the two front ribs as a guide
and snap into place from the top.
Funnel
Washing the funnel ensures a fresh
beverage experience. The funnel
should be washed regularly and can
be removed from the K-Cup® pod
holder by pulling on it until it pops off.
To replace it, orient the snaps to the
indent and just snap it back onto the
K-Cup® pod holder.
STRONG
STRONG
Exit Needle
Remove the pod holder assembly
and detach the funnel. Locate the
exit needle on the inside bottom
of the K-Cup® pod holder. Insert a
straightened paper clip into the exit
needle to loosen any coffee grounds.
Entrance Needle
Lift the brewer handle and locate the entrance needle on the
underside of the lid. To clean both holes in the needle, hold
the brewer handle in the upward position and with your other
hand, carefully insert a straightened paper clip into both
holes. Gently move it around to loosen any coffee grounds.
Lower the handle completely and run two water-only brew
cycles. Do not insert a K-Cup® pod.
TIP: Refer to support.keurig.com for video instructions on cleaning the entrance/exit needles.
CAUTION: There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the
bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
NOTE: Always remove and dispose of the used K-Cup® pod after brewing.
Before you begin, you will need a large ceramic mug, fresh
water, Keurig® Descaling Solution, and access to a sink.
Do not use a paper cup. Ensure that there is no beverage
pod in the K-Cup® pod holder. Please allow approximately
15-20 minutes for the descaling procedure.
STEP 1: Descaling Solution Rinse
Pour the entire bottle of Keurig® Descale Solution into an
emptied water reservoir. Then, fill the empty bottle with
water and pour into the water reservoir. Do not insert a
K-Cup® pod.
Place a large mug on the drip tray. To activate Descale
Mode, begin with the brewer powered off by pressing
and holding BREW OVER ICE button, then press and hold
the 8oz and 12oz buttons together for 3 seconds until the
DESCALE light turns solid.
When BREW button begins flashing, press the BREW
button to start the cleansing rinse brew. Pour the hot liquid
into the sink. Repeat the cleansing rinse process until the
ADD WATER light illuminates.
STEP 2: Rest & Rinse
Empty the water reservoir and refill to the MAX fill line
with fresh water.
STEP 3: Fresh Water Rinse
Press the BREW button once it begins flashing. Repeat this
process until the ADD WATER light illuminates. The brewer
will now exit Descale Mode and will be ready
for use!
NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed
from the brewer. This is natural, as the solution is reacting with the scale inside.
For a brewer that is heavily scaled, the brewer may not fill properly after the
descaler is added. If this occurs, you may see only a small or no output dispensed,
followed by the sound of air blowing out. If this occurs:
• Turn off and unplug the brewer.
• If there is Keurig® Descaling Solution in the water reservoir, discard the
contents, rinse the water reservoir thoroughly and refill with water
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse
cycle. The brewer should begin to function normally as the solution is rinsed out
and the scale is removed. If problem persists, allow brewer to sit unplugged for
at least 30 minutes before continuing with the rinse.
Descaling Your Brewer

Troubleshooting
Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and
can be cleaned using a straightened paper clip or similar tool.
• Clean the exit needle of the K-Cup® pod holder. Refer to the
Exit Needle care instructions.
• Clean the brewer entrance needle. Refer to the Entrance
Needle care instructions.
Brewer Will Not Brew
• A minimum of 6oz of water is required to brew. Add an
additional 2oz of water to the reservoir to ensure
the minimum fill level has been met, then press the
BREW button. Repeat until the brewer begins to dispense.
Brewing a Partial Cup
• Power the brewer off. Press and hold the BREW button and
12oz button for 5 seconds until water starts dispensing. Then
release and let the water purge. Discard the contents into
the sink. Press the POWER button to restart.
• The exit needle may be clogged. Refer to the Exit Needle
care instructions.
• Clean the K-Cup® Pod Holder, see K-Cup® Pod Holder care
instructions.
• The brewer may need to be descaled. If you have repeated
the descale procedure on your brewer two times and it is
still only brewing a partial cup, contact Customer Service.
Brewer Does Not Have Power or Shuts Off
• Make sure that the power button has been turned on.
• Plug brewer into its own grounded outlet. If the electric
circuit is overloaded with other appliances, your brewer may
not function properly. The brewer should be operated on its
own circuit, separate from other appliances.
• For energy savings, the brewer automatically turns off
5 minutes after the last brew. Press the power button to
restart.
• If the brewer still doesn’t have power, contact Customer
Service.
Helpful Hints
Water quality varies greatly. If you notice an undesirable
taste in your beverage (such as chlorine or mineral tastes),
we recommend using bottled or filtered water. Do not use
distilled water.
Service
Beyond these recommended cleaning and maintenance
procedures, this brewer is not user serviceable. For service,
please refer to the Warranty section of this guide.
Storage
Empty the water reservoir before storing or transporting
and take care to ensure that you store your brewer in a
safe and frost-free environment. When you prepare to use
it after storage, we recommend rinsing the water reservoir
with fresh water and descaling the brewer as detailed in the
Descaling your Brewer section.
If you plan to move your brewer to a different location, turn
the brewer off, unplug it, and empty the water reservoir.
If your brewer has been in an environment below freezing,
please be sure to let it warm to room temperature for at
least 2 hours before using.
Have Questions?
We’re here to help. Visit Support.Keurig.com for
step-by-step videos on cleaning, descaling, and more.
Still Need Help?
Give us a call at
1-866-901-BREW (2739)
Click or Call!

Slim®
+ICED™
LIMITED ONE YEAR WARRANTY
Keurig Green Mountain, Inc. (Keurig) warrants that your brewer will
be free of defects in materials or workmanship under normal home
use for one year from the date of purchase. It is recommended
that you register your brewer on keurig.com/new so that your
purchase information will be stored in our system. Keurig will, at its
option, repair or replace a defective brewer without charge upon its
receipt of proof of the date of purchase. If a replacement brewer is
necessary to service this warranty, the replacement brewer may be
new or reconditioned. If a replacement brewer is sent, a new limited
one year warranty will be applied to the replacement brewer.
This warranty only applies to brewers operated in the United States
and Canada. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state and, in the
case of Canada, from province to province.
Only the use of Keurig® K-Cup® brand pods and accessories will
guarantee the proper functioning and lifetime of your Keurig®
brewer. Any damage to or malfunction of your brewer resulting
from the use of non-Keurig® pods and accessories may not be
covered by this warranty or may result in a service fee if the damage
or malfunction is determined to be caused by such use.
WHAT IS NOT COVERED BY THE LIMITED WARRANTY?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR
INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND
DOES NOT COVER INCIDENTAL COSTS AND EXPENSES
RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF
FORESEEABLE. Some states or provinces do not allow the exclusion
or limitations of incidental or consequential damages, so the above
limitation or exclusion may not apply to you depending on the state
or province of purchase.
Nor does this warranty cover damages caused by use of non-Keurig®
pods or accessories, services performed by anyone other than
Keurig or its authorized service providers, use of parts other than
genuine Keurig® parts, or external causes such as abuse, misuse,
inappropriate power supply, or acts of God.
OTHER LIMITATIONS
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY
OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL.
IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS
ALL OTHER WARRANTIES WITH RESPECT TO YOUR
KEURIG® BREWER, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
PURPOSE. Some states or provinces do not allow disclaimers
of such implied warranties or limitations on how long an implied
warranty lasts, so the above limitation may not apply to you
depending on the state or the province of purchase.
HOW DO YOU OBTAIN WARRANTY SERVICE?
Keurig® brewers are high-quality appliances and, with proper care,
are intended to provide years of satisfying performance. However,
should the need arise for warranty servicing, simply call Keurig
Customer Service at our toll free phone number 1.866.901.BREW
(2739). Please do not return your brewer for servicing without first
speaking to Keurig Customer Service to obtain a Return Materials
Authorization (RMA) number. Keurig® brewers returned without a
RMA number will be returned to the sender without servicing.
Warranty
B
A
C
D
E
F
GI
H
A. Handle
B. K-Cup® Pod Holder (B
and C are the K-Cup®
Pod Holder Assembly)
C. Funnel
D. K-Cup® Pod Assembly
Housing
E. Drip Tray Plate
F. Drip Tray
G. Drip Tray Base
H. Water Reservoir Lid
I. Water Reservoir
For replacement parts, please visit www.keurig.com
SINGLE SERVE COFFEE MAKER

Coffeehouse taste
in your own home.
FIND YOUR PERFECT POD
With over 75 brands and hundreds
of varieties, ind your match at
Keurig.com/New
DC0000008345 REV A