Keys Fitness HealthTrainer HT601 User manual

HEALTHER TRAINER 601 TREADMILL
OWNER’S MANUAL
Model Name HT601
Serial Number
Purchase Date
Write down for future reference.
Keys Technical Service, [phone]
KEYS Fitness Products, LP
P.O. Box 551239
Dallas, TX 75239-1239
Part# 15-0147

Table of Contents
Table of Contents 2
Specification Sheet 3
Important Safety Information 4
Before You Start 5
Warm Up Exercises 6
Assembly, Moving Instructions 7
Power Requirements 8
Console Functions and Descriptions 9
Program and Operating Instructions 10, & 11
Program Descriptions and Profiles 12
Belt Adjustments and Tension 13
Change to MPH or Km/H 14
Maintenance Instructions 15
Troubleshooting Guide 16
Error Messages 17
Calibration Sequence 18
Parts and Diagrams 19
Warranty Registration (Mail In Form) 20
Information Page#
2

Specification Sheet
HT601
Horsepower (Continuous) 2.0hp
Display Type 5 Window LCD
Electronics One touch
Speed & Incline Toggle Switches Yes
One Touch Speed & Incline Bar Yes
Pre-Set Programs 3
Semi-Custom Programs 6
Power Incline 12%
Roller Diameter 1.9”
Cushioned Deck Yes
Speed Range 0-10mph
Walking Belt 18 X 51” 2 ply
Side Hand Rails Yes
Foot Print 29” x 61”
Folded Foot Print 29 x 29”
User Capacity 275lb
Warranty Motor 10 Years
Warranty Parts 2 Years
Warranty Labor 1 Year
Warranty Frame Lifetime
3

Important Safety Information
WARNING! Before using this treadmill or starting any exercise program, consult your physician. This
is especially important for persons over the age of 35 and/or persons with pre-existing health prob-
lems. The manufacturer or distributor assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is
important to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
!It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual
and are familiar with warnings and safety precautions.
!The treadmills have a user maximum capacity of 275 pounds.
!The treadmill should only be used on a level surface and is intended for indoor use only. The tread-
mill should not be placed in a garage, patio, or near water and should never be used while you are wet.
KEYS recommends a treadmill mat be placed under the treadmill to protect floor or carpet and for
easier cleaning.
!Follow safety information in regards to plugging in your treadmill. Keep the power cord away from
the incline wheels and do not run the power cord underneath your treadmill. Do not operate the tread-
mill with a damaged or frayed power cord.
!Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the
treadmill with bare feet, sandals, socks or stockings.
!Always straddle the belt and allow it to start moving before stepping onto the belt.
!Hold on to handrails when adjusting speed, incline, or other controls.
!Always examine your treadmill before using to ensure all parts are in working order.
!Allow the belt to fully stop before dismounting.
!Pets should never be allowed near or on the treadmill.
!Do not leave children unsupervised near or on the treadmill.
!Never operate the treadmill where oxygen is being administered, or where aerosol products are being
used.
!Never insert any object or body parts into any opening.
!For safety and to prevent damage to your treadmill, no more than one person should use the tread-
mill at a time.
!Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only
be performed by an authorized service representative, unless authorized and/or instructed by the
manufacturer
!Failure to follow these instructions will void the treadmill warranty.
!Never leave the treadmill unattended while it is running
4

Thank you for purchasing theHEALTH TRAINER 601 TREADMILL! This quality product you
have chosen was designed to meet your needs for cardiovascular exercise.
Before you start, please read the Owner's Manual and become familiar with the operation of your
new treadmill.
Remember to take the time to perform the stretching exercises provided to avoid injury.
!Do not stand on the walking belt while pressing the Power button or Start/Stop button.
!Always adjust the speed of the treadmill in small increments as this treadmill is capable of high
speeds.
!If you are taking medication, consult your physician to see if the medication will affect your exer-
cise heart rate.
!If you have heart problems, you are not active, and/or are over the age of 35 years, do not use
the pre-set treadmill programs or start an exercise program without first contacting and receiving
approval from your physician.
!To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the con-
sole. KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.
!Please review the following drawing below to familiarize yourself with the listed parts.
This manual covers several treadmills, so the one pictured below may not be identical to
your particular model
5Before You Start
READING RACK
WHEEL
SAFETY LATCH
UPRIGHTS
SIDE HAND RAILS
WALKING BELT
CONSOLE
CIRCUIT BREAKER
MOTOR COVER
WATER BOTTLE HOLD-
ER(WATER BOTTLE
NOT INCLUDED)
REAR ROLLER-
ADJUSTMENT
BOLTS

TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend forward from your hips. Allow
your back and shoulders to relax as you reach down toward your toes as far as possi-
ble. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees,
and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. This will stretch your hamstrings, lower back, and
groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your hands against a wall.
Keep your back leg straight and your back foot flat on the floor. Bend your front leg,
lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To
cause further stretching of the Achilles tendon, bend your back leg as well. This will
stretch your calves, Achilles tendons, and ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp one foot with your
other hand. Bring your heel as close to your buttocks as possible. Hold for 15
counts, then relax. This will stretch your quadriceps and hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward. Pull your feet
toward your groin area as far as possible. Hold for 15 counts, then relax. This
will stretch your quadriceps and hip muscles.
EXERCISE GUIDELINES
WARNING! Before beginning this or any exercise program, you should consult your physician. This is
especially important for individuals over the age of 35 or individuals with pre-existing health problems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the
muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light
exercise to warm up. The photos on this page show several forms of basic stretching you may perform
before your workouts. In order to achieve an adequate warm-up, perform each stretch three times.
6
Warm Up Exercises

Assembly
This HEALTH TRAINER 601 treadmill is shipped in one piece and fully assembled. After opening
the box, remove any packing materials from the treadmill. Do not throw away any packing materials
until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical
cord will easily reach an electrical outlet.
Moving
CAUTION! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREAD-
MILL WHILE IT IS IN THE UNFOLDED OPERATING POSITION. TO REDUCE THE
POSSIBILITY OF INJURY WHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACK
STRAIGHT. AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR
BACK. IN ORDER TO RAISE OR LOWER THE TREADMILL SAFELY, YOU MUST BE
ABLE TO LIFT 45 POUNDS (20KG). IT IS SUGGESTED YOU ALWAYS USE THE AID OF
A SECOND PERSON WHEN MOVING THE TREADMILL.
With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails and
place one foot on the base as shown in the photo below. Next, with a firm grasp on handrails, place
one foot on the center of the base crossbar and carefully tilt the treadmill back until it rolls freely on
the wheels. Using extreme caution, move the treadmill to the desired location. To set the treadmill
down, place one foot on the center of the base crossbar and carefully lower treadmill onto base in
resting position. Do not attempt to move the treadmill over an uneven or rough surface.
7Assembly Instructions

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN
RESULT IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELEC-
TRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PROD-
UCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH
THE PRODUCT IF IT WILL NOT FIT THE OUTLET. HAVE A PROPER OUTLET
INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power.
Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances
being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not
included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single out-
let surge protector with UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with UL sup-
pressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of
least resistance for electric current should the treadmill malfunction. This treadmill comes with an electri-
cal cord with an equipment-grounding conductor and a grounding plug. Always plug the power cord into
a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug
illustrated in the drawing below.
8
Power Requirements

There are five display windows on the control panel to provide feedback information.
WORKOUT TIME
!TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59
seconds)
!INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds
and counting to 0 seconds
SPEED WINDOW
!SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
!DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments
starting at 10.0
!CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline,
and time
INCLINE WINDOW
!INCLINE: Indicates incline in percent of grade 0-12% in 0.5 increments
CENTER BRICKYARD WINDOW
!Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode,
shows the change in speed profile across the interval range (1-10) and shows position with a blinking
action.
!In Program mode, the treadmill will display the name of the program selected This is shown on the
left hand side of the window. In Manual mode, the LAP counter will appear in the top center of the
window, counting each 1/4 mile lap in sequence of completion (1, 2, 3, etc.)
9
INCLINE WINDOW
TIME WINDOW CALORIE/DISTANCE WINDOW
SPEED WINDOW
Console Functions and Descriptions

QUICK START / MANUAL MODE
!Plug into a surge protector outlet. Attach the Red Safety Key on to the treadmill console.
!Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
!Press POWER button. There will be an eight (8) second delay after pressing the POWER button
before data can be entered. The WORKOUT TIME window will flash.
!Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the
belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or –
(decrease) button.
!To end your workout, press START/STOP button. Belt will gradually slow to zero.
!To pause your workout, press PAUSE.
!To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT
WILL RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUS-
ING.
!Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to get-
ting started. After pressing the POWER button, the time window will blink. Use the SPEED + or –
arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED win-
dow will now be flashing. Using the same + or – arrows, select the speed for your workout, then
press ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or –
arrows to set your workout incline, then press ENTER PROGRAM. To start, press the
START/STOP button.
10
Program and Operating Instructions
STOP/START
ENTER PROGRAM
POWER
PAUSE
INCLINE SPEED

11
FAT BURN
CARDIO
WARM UP
START/STOP
POWER
PAUSE
INCLINE
SPEED
Program and Operating Instructions
PROGRAM MODE
Plug treadmill into a surge protector outlet. Attach the Red Safety Key on to the treadmill console.
!Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
!Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME
window will flash.
!There are three (3) pre-set and six (6) semi-custom pre-set programs on the HEALTH TRAINER 601
treadmill. The treadmill includes FAT BURN, CARDIO, and WARM-UP programs. To select the program
press the corresponding button on the console display
!Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt
starts moving.
!CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-
up, Cross Training) can be customized in the P1 or P2 mode. After making the program selection, the
Calorie window will read “OP”. The “OP” refers to “original program” and is preset. The program
name you select will display in the diode light beside the program name. Press the same program button
once more and the Calorie window will read P1. The “P1” mode is now accessed. You can now program
the Time, Speed, and Incline in P1 mode, which will be saved for future workouts.
1) The WORKOUT TIME window will blink. Use the SPEED + or – arrows to select your workout
time. Press ENTER PROGRAM.
2) The SPEED window will then blink. Use the same + or – arrows to select the speed for your work-
out. Press ENTER PROGRAM.
3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline.
Press ENTER PROGRAM.
To start, press the START/STOP button. To access P2 mode, press the selected program button three
times (once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.
!TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have pro-
grammed the P1 or P2 modes, you will need to use the PAUSE button to change the program you previ-
ously entered. For instance to change to a new setting in P1-FAT BURN, press the FAT BURN button
twice to access P1. Then press the PAUSE button to get the WORKOUT TIME window to flash.
Follow the directions above to continue to change the program.

12
The Fat Burn Program is
designed to vary the treadmill
elevation, while maintaining a
constant walking belt speed.
The Cardio Program is designed
to vary the treadmill Speed, while
maintaining a constant Elevation.
The Warm Up Program is designed to gradually
increase the treadmill Speed and Elevation in the first
segment (warm up) and gradually decrease the treadmill
Speed and Elevation in the last segment (cool down).
This is also known as a Plateau program.
12
11
10
9
8
7
6
5
4
3
2
11 2 3 4 5 6 7 8 9 10
SPEED
INCLINE 12
11
10
9
8
7
6
5
4
3
2
1
1 2 3 4 5 6 7 8 9 10
SPEED
INCLINE
12
11
10
9
8
7
6
5
4
3
2
11 2 3 4 5 6 7 8 9 10
SPEED
INCLINE
Program Profiles

WARNING! Do not overtighten rollers! This will cause premature
roller bearing failure!
Belt adjustment and tension performs two functions: adjust-
ment for tension and centering. Your new treadmill comes
pre-adjusted from the factory for tension and centering.
Please follow the procedures below if the belt shifts to the
left or right while walking:
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)
First, turn treadmill on to run at 1 mph. Using the hex key provided,
turn the left rear roller adjustment bolt ¼ turn in the clockwise direction.
Next, run the treadmill at 2.5 mph. You should see the belt start to correct
itself by moving back towards the center. Repeat the above procedure until
the walking belt is centered. It may be necessary to set walking belt tension
once you have completed this procedure if the belt feels like it is slipping
while walking. Refer below to the “Walking Belt Slipping” instructions.
WALKING BELT IS SHIFTING TO THE RIGHT (Diagram
2)
First, turn the treadmill on to run at 1 mph. Using the hex key
provided, turn the right rear roller adjustment bolt ¼ turn in the
clockwise direction. Next, run the treadmill at 2.5 mph. You
should see the belt start to correct itself, moving back towards
the center. Repeat the above procedure until the walking belt is cen-
tered. It may be necessary to set walking belt tension once you have
completed this procedure if the belt feels like it is slipping while walking.
Refer below to the “Walking Belt Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using the hex key
provided, turn both left and right rear roller adjustment bolts the same dis-
tance, usually a ¼ turn in the clockwise direction. Plug the
power cord back into the surge protector and run the tread-
mill at 2.5 mph. You should now walk on the belt to deter-
mine if the belt is still slipping. Repeat the above procedure
until the walking belt is not slipping. The tension should be just
tight enough not to slip.
!Turning the hex key counter clockwise brings the rear
rollers and belt towards you.
!Turning the hex key clockwise pushes the rear roller and
belt away form you.
13 Belt Adjustment and Tension

Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour).
All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to
read in kilometers, follow the steps described here:
1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the con-
sole.
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the
backside of the console (see diagram below).
3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.
4) Pressing the SPEED +/- button will activate your choice.
5) To accept the setting, press the POWER button.
14
Change Miles per hour to Kilometers per hour

15
WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from
the surge protector.
CLEANING
Routine cleaning of your Keys Fitness treadmill will extend the life of your treadmill. WARNING! To
prevent electrical shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall
electrical outlet before attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water
dampened soft cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts
the belt and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking
board be checked periodically for lubrication to ensure optimal treadmill performance.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the
walking board as far under as you can reach. If you feel signs of silicone, no further lubrication is
required. If it feels dry to the touch, follow the instructions below.
KEYS recommends “Lube N Walk” for cleaning and lubricating the treadmill belt and deck. Ask your
retailer or call KEYS at 888-340-0482. You may also use silicone such as “Napa 8300” (available at most
stores).
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walk-
ing board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the
board approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board,
moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray
approximately 4 seconds on each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
WARNING: Do not over lubricate the walking board. Excess lubricant should be wiped off with
a clean towel.
Maintenance Instructions

16
Treadmill will not start.
1 Is the Safety Key inserted into the treadmill Console?
2 Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on
page 8)
3 Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has
tripped. Wait five minutes and then press the switch back in.
4 Check the house electrical breaker box and the circuit breaker for the room where the treadmill is
located. If it has tripped, reset or have an electrician replace the breaker in home.
5 Have an electrician check for inadequate voltage at the outlet.
Treadmill loses power during use.
1 Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has
tripped. Wait five minutes and then press the switch back in.
2 Check the house electrical breaker box and the circuit breaker for the room where the treadmill is
located. If it has tripped, reset or have an electrician replace the breaker in home.
3 If the treadmill still will not operate, please call Keys Technical Service at [phone].
Treadmill walking belt slows during use.
1 Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the
outlet.
2 If treadmill still will not operate, please call Keys Technical Service at [phone].
Treadmill walking belt slips or is not centered on rear roller.
1 Refer to “Belt Adjustment and Tension” section on page 13.
2 Need help? Call Keys Technical Service at [phone].
Troubleshooting Guide

17
Treadmill Error Messages.
Your treadmill is equipped with a software package that enables error messages to be displayed
when there is a problem. The following error codes will be displayed in the console display win-
dows.
Safety Interlock Error Messages
SI 1 - Safety key missing, replace and try again.
SI 2 - Over voltage protection trip. Notify Keys Fitness Technical Service.
SI 3 - Tilt Switch Trip. Notify Keys Fitness Technical Service.
Other Error Messages
E11 - Lack of speed feedback data from belt motor. Attempt re-calibration. See Calibration
Sequence section for detailed information.
E22 - Under Speed condition detected from the belt motor. Attempt re-calibration. See Calibration
Sequence section for detailed information.
E33 - Over Speed condition detected from the belt motor. Attempt re-calibration. See Calibration
Sequence section for detailed information.
To avoid possible damage to the treadmill and the possibility of injury, do not operate the
treadmill until the problem is corrected. Call Keys Technical Service at [phone].
Error Messages

18
Your treadmill is equipped with a software package that will perform a calibration sequence unique to
your specific model number. Please perform the following steps to calibrate the HEALTH TRAINER
601 TREADMILL.
1. Unplug power cord from outlet strip.
2. Attach Safety Key to console.
3. Plug power cord into outlet strip.
4. Initiate calibration sequence. Locate hole on the back of the console and insert the eraser end of a
pencil through the hole and press the calibration switch twice. As show on page 14.
5. CL21 should appear in the Time window, if not, continue to press the calibration switch until CL21
appears.
Note: During the calibration sequence, the Time window will display which step you are at in the
process (C21, C22, C23 and so on). The CAL/DIST window will display which key should be entered
next. For example, “E” for Enter, “P” for Power, or “SS” for Start / Stop.
6. CL21: MPH or KPH will be flashing in the Speed window, pressing the Speed +/ - button will toggle
options. Choose MPH (KPH), press Enter.
7. CL22: 8, 10, or 12 (13, 16, or 20 in KPH mode) will be displayed in the Speed window, pressing the
Speed +/ - button will toggle options. Choose 10 (or 16 for KPH mode), press Enter.
8. CL23: FFF, UUU, or HHH will be displayed in the Speed window, pressing the Speed +/ - button
will toggle options. Choose FFF, press Enter.
9. CL24: 111 or 222 will be displayed in the Speed window, pressing the Speed +/ - button will toggle
options. Choose 111, press Enter.
10. CL25: AL1 or AL2 will be displayed in the Speed window, pressing the Speed +/ - button will tog-
gle options. Choose AL2, press Enter.
11. CL26: OPA or OPI will be displayed in the Speed window, pressing the Speed +/ - button will tog-
gle options. Choose OPA, press Enter.
12. CL27: Blank (nothing), “a”, “b”, “c”, or “d” will be displayed in the Incline window, pressing the
Speed +/ - button will toggle options. Choose Blank, press Enter.
13. CAL/DIST window will display “E”, Press Enter. “55” will display in CAL/DIST window.
14. Press Start/ Stop.
15. At this time, make sure you are not standing on the walking belt, as the machine will automatically
initiate belt movement and run through a complete calibration and diagnostic routine.
Press Enter, belt will begin to move, unit will begin self-calibration.
16. When Speed and Incline calibration has finished, press Power button twice, display should blank,
and treadmill should be ready for use.
To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected. Call Keys Technical Service
at [phone].
Calibration Sequence

HT601
1 Left Side Extrusion Rail 05-0036
2 Right Side Extrusion Rail 05-0036
3 Treadmill Belt 04-0025
4 Front Roller Assembly 24-0218
5 Rear Roller 09-0013
6 Treadmill Deck 03-0011
7 End Cap (L/R) 06-0008
8 Elevation Motor (actuator) 12-0022
9 3 Piece Bottom Motor Pan 06-0018
06-0019
06-0020
10 Small Fan 06-0080
11 Motor 12-0023
12 Poly V Belt 04-0004
13 Motor Hood Cover Top 06-0105
15&16 Console Assembly 24-0249
19
Please review the following drawing below to familiarize yourself with the listed parts. This man-
ual covers several treadmills, so the one pictured below may not be identical to your particular
model.
Parts & Diagrams

KEYS FITNESS TREADMILL WARRANTY REGISTRATION
FIRST
APT. NO.ADDRESS
M.I. LAST
ZIP
STATE
CITY
TELEPHONE
KEYS FITNESS respects the rights of your privacy. Our
company will not sell or distribute to others the information
above. This information is used to track our product quality and
to contact you in the event of a product safety concern. It may
be used to offer you future Keys products only through the mail.
Please check here if wish not to receive any additional
information on Keys products.
DATE OF PURCHASE SERIAL NO.
MODEL NO.
Name of store or company where
purchased:
Howdo you plan to use the treadmill?
Walk____ Run_____ Both_____
Who will use the treadmill?
Male____ Female_____ Both_____
Howmany family members? _____
AGE: 15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
Where did you learn about treadmills?
TV____ Radio____ Friend____
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
Why did you purchase a treadmill?
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
Other __________________________
Howimportant areeach feature:
Least Most
Unique Features
Horsepower
Warranty
Price
Look/Design
Folding Feature
Other Comments:
_______________
_______________
_______________
_______________
KEYSFITNESS PRODUCTS, LP – LIMITED WARRANTY
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States and Canada onlyto products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the Keys
brand name. The warrantyperiod to the original purchaser of the HT601 treadmill is (lifetime) on the frame and one (1) Year labor. In addition, the HT601 includes ten (10) years
on the motor and a two (2) year parts warranty.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free
fromdefectsin materialsor workmanshipunder normaluse during the warrantyperiod. Your sales receipt,showing the date ofpurchase of the Product, isyour proofof the date
of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes
expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician unless otherwise
authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless
accompanied bywritten authorization byKeys Fitness).
During the warrantyperiod Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions,or otherwise fails to
conformwith this Limited Warrantyunder normal non-commercial, personal,family or household use. In repairing the Product,Keys may replace defective parts, or at the option
of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warrantywill become the propertyof
Keys. Keys reservesthe right to change manufacturers of anypart to cover anyexisting warranty.
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts
determined to be defective must be returned to Keys to obtain warranty service. You must prepayany shipping charges,export taxes, custom duties and taxes, or any other
charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of
loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-
purchase documents willbe cause tovoid this Limited Warranty.
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does notextend to any Product
that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold byKeys; (c) by modification of the
Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized Keys warranty service
provider. Producton which the serial number hasbeen defaced or removed isnot eligible for warrantyservice. Should any Product be submitted for warrantyservice be found
ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements for
payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL
BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited
Warrantygives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded
products. Keys neither assumes nor authorizes anyone to assume for it anyotherexpress warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHINTEN(10) DAYS OF PURCHASE OR REGISTER YOUR TREADMILL ONLINE AT
www.keysfitness.com KEYS FITNESS PRODUCTS, P.O. BOX 551239, DALLAS, TX 75355-1239. THANK YOU!