Keysight Technologies N1060A User manual

Electrical channel input
circuits can be damaged by electro-
static discharge (ESD). Therefore,
avoid applying static discharges to the remote head’s
input connectors. Prior to connecting any coaxial cable
to the connectors, momentarily short the center and
outer conductors of the cable together. Avoid touching
the front-panel input connectors without first touching
the frame of the instrument.
Static
Sensitive
Channel Inputs
Max. input signal: ±1Vpp (+10 dBm)
Max. 1.0 mm connector torque: 4 lb-in. (0.45 Nm)
Max. 2.92 mm connector torque: 5 lb-in. (0.57 Nm)
Read accessory kit user’s guide for critical information.
Avoiding Expensive Repairs
Refer to the accessory kit user’s guide for
instructions on safely connecting devices to the N1060A
front-panel RF connectors without causing expensive
damage.
N1000A Help System
Search on
N1060A
Installation
5. Click Help > Contents to view help system. Search on
N1060A for documentation.
1. On the N1000A DCA-X, click Help > About and check
firmware version. Minimum required FlexDCA Firmware
Version is A.06.00. Download the firmware at:
www.keysight.com/comms/dca
2. Insert the N1060A into the left three front-panel slots
in the N1000A’s module bay.
3. Finger tighten the front-panel knurled locking screws.
4. Remove the screw-on channel shipping protectors.
Precision
Timebase
Input
(2.92 mm)
Recovered
Clock Output
(2.92 mm)
0.5 Vpp Nom
50 Ω
2.4-32 GHz
±
2 V Max
Ch A/CDR+
±
1V Max
Ch B/CDR
-
±
1V Max
CDR Rates
Adjustable Loop
N1060A
Precision Waveform Analyzer 50 GHz BW
Screw-on
shipping protectors
DCA-X
DCA-X Series Wide-Bandwidth Oscilloscope N1000A
1 2 3 4
Trigger
Input
(2.92mm)
DC Cal
50Ω
DC-32GHz
2Vpp Max
±
Precision
Timebase
Input
(2.92mm)
50Ω
2.4-44GHz
2V Max
Marker
Position
Vertical
Horizontal
Acquisition
Armed
Triggered
Press to
select
Press to
select
Precision
Timebase
Input
(2.92mm)
Recovered
Clock Output
(2.92mm)
0.5Vpp Max
50Ω
2.4-32GHz
1.3Vpp Max
Ch A/CDR+
±
2V Max
Ch B/CDR
-
±
2V Max
CDR Rates
Adjustable Loop
N1060A Precision Waveform Analyzer 85 GHz BW
Locking Screws
N1060A
N1060A Precision Waveform Analyzer

© Keysight Technologies 2018
Printed in USA. October, 2018
N1060-90002
*N1060-90002*
This product is designed for use in Installation
Category II and Pollution Degree 2 per IEC 1010 and respec-
tively.
If this product is not used as specified, the protec-
tion provided by the equipment could be impaired. This product
must be used in a normal condition (in which all means for
protection are intact) only.
No operator serviceable parts inside. Refer servic-
ing to qualified service personnel. To prevent electrical shock
do not remove covers.
To prevent electrical shock, disconnect the instru-
ment from mains before cleaning. Use a dry cloth or one
slightly dampened with water to clean the external case parts.
Do not attempt to clean internally.
This product has been designed and tested in accordance
with IEC Publication 1010, Safety Requirements for Electron-
ic Measuring Apparatus, and has been supplied in a safe
condition. The instruction documentation contains informa-
tion and warnings which must be followed by the user to
ensure safe operation and to maintain the product in a safe
condition.
Install the plug-in module according to the enclosure
protection provided.
This instrument does not protect against the ingress of
water. This instrument protects against finger access to
hazardous parts within the enclosure.
Safety considerations
Basic Module Configuration
1. Connect the input signal to a channel input.
2. On N1000A, click Setup > Modules > Precision
Waveform Analyzer.
3. In the dialog box’s Channels tab, turn on the appropri-
ate channel.
4. In the Clock Recovery tab, select the Input channel.
5. Select the Data Rate.
6. Configure the Clock Recovery Loop Bandwidth and
Peaking settings, as appropriate.
7. Click the Lock button.
8. On the Precision Timebase tab, click Enable Precision
Timebase.
9. For additional information, consult the N1000A help
system.
Clock tab
Step 3. Turn on channel in Channels tab
Step 4. Select Channel Source
Step 8. Enable Precision Timebase
Step 5.
Select Data Rate
Step 6.
Loop Characteristics
Step 7.
Click Lock button
Select loop bandwidth (LBW)