Endress+Hauser Promonitor NRF560 User manual

BA00425G/08/EN/02.12
71201677
Valid as of Software-Version: V.1.94
Operating Instructions
Promonitor NRF560
Tank Side Monitor

Promonitor NRF560
2Endress+Hauser
Basic device layout of the Promonitor NRF560
Promonitor NRF560 with Proservo NMS5 configuration
Promonitor NRF560 is a monitoring unit for use with the Proservo NMS5 of tank gauges.
The Proservo NMS5 can be operated to measure the level, interface level, bottom level, or to hoist the displacer.
Mounted at the tank side or up to 1200 meters away (local HART®connection).
Promonitor provides indication of measured level, temperature data and operating status, and can send operating commands to the Proservo NMS5
from a convenient location.
Ptomonitor NRF560 is operated by three visual operating elements, namely the keys "E" , "- ", and "+".
Local HART
Power (AC / DC)
Power (AC / DC)
Output: Primary Digital
VI Serial bus
RS 485
HART
Mark Space
WM 550
Enraf BPM
Output: Secondly Analog
4 SPST, alarm output
4 - 20mA x 2 channel
Promonitor
NRF560
Displacer position for:
Temperature display
Displacer operation
Prothermo
NMT53 series
Temperature
Liquid
&
Gas / vapor
Level
Tank bottom
Interface level
Density
Proservo
NMS5/7
R
R
E
+
-
LEVEL
U-D
0.0°C
LEVEL
U-D
0.0°C
Level
Temperature
Displacer status
Gauge status
Liquid Level
Interface Level
Bottom Level
1
2
3

Promonitor NRF560
Endress+Hauser 3
Table of Contents
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Installation, commissioning and operation . . . . . . . . . . . . 4
1.3 Operation safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Notes on safety conventions and symbols . . . . . . . . . . . . . 5
2 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Product structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Supplied documentation . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5 Certificates and approvals . . . . . . . . . . . . . . . . . . . . . . . 10
2.6 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Inatallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.1 Incoming acceptance, transport, storage . . . . . . . . . . . . . 11
3.2 Installation Condition . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Installation variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.1 Connection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.3 Cable Gland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
5.1 Display and Operating Elements . . . . . . . . . . . . . . . . . . . 17
5.2 Functions of the operating Elements . . . . . . . . . . . . . . . . 18
5.3 Programming Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.4 Access Code Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.5 Setting for Promonitor NRF560 Connections . . . . . . . . . . 20
5.6 How to Select an Access Code . . . . . . . . . . . . . . . . . . . . 21
5.7 HOME Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6 Promonitor NRF560 Programming Matrix . . . . . . . .24
6.1 Description of the Programming Matrix . . . . . . . . . . . . . 25
7 Proservo NMS5 Programming Matrix . . . . . . . . . . . .26
8 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
9 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
10.1 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
10.2 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10.3 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10.4 Contact addresses of Endress+Hauser . . . . . . . . . . . . . . . 33
11 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
11.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . . . . . . 34
Table of Contents

Promonitor NRF560
4Endress+Hauser
1 Safety instructions
1.1 Designated use
The Promonitor NRF 560 is a tank side monitor and control station for the Proservo NMS5 of intelligent tank
gauges.
The Promonitor NRF560 is a simple low-cost tank site monitor for displaying interface level, tank bottom level,
and temperature. Additionally, the Proservo NMS5 can be operated to measure the level, interface level,
bottom level, or to hoist the displacer. The tank gauge is operated by three visual operating elements (ìtouch
controlî). For the transmission between the Proservo NMS5 and the Promonitor NRF560, a two-wire HART®
protocol is utilized.
1.2 Installation, commissioning and operation
• Mounting, electrical installation, start-up and maintenance of the instrument may only be carried out by
trained personnel authorized by the operator of the facility.
• Personnel must absolutely and without fail read and understand these installation instructions before
carrying out the procedures..
• The instrument may only be operated by personnel who are authorized and trained by the operator of the
facility. All instructions in this manual are to be observed without fail.
• The installer must make sure that the measuring system is correctly wired according to the wiring diagrams.
The measuring system is to be grounded.
• Please observe all provisions valid for your country and pertaining to the opening and repairing of electrical
devices.
1.3 Operation safety
1.3.1 Hazardous areas
Measuring systems for use in hazardous environments are accompanied by separate "Ex documentation",
which is an integral part of this Operating Manual. Strict compliance with the installation instructions and
ratings as stated in this supplementary documentation is mandatory.
• Ensure that all personnel are suitably qualified.
• Observe the specifications in the certificate as pipe as national and local regulations.
Caution!
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
1 Safety instructions

Promonitor NRF 560
Endress+Hauser 5
1.4 Notes on safety conventions and symbols
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding symbol in the margin.
Safety conventions
Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to
personal injury, a safety hazard or destruction of the instrument
Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the instrument
Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned
Explosion protection
Device certified for use in explosion hazardous area
If the device has this symbol embossed on its name plate it can be installed in an explosion
hazardousarea
Explosion hazardous areas
Symbol used in drawings to indicate explosion hazardous areas. Devices located in and
wiringentering areas with the designation “explosion hazardous areas” must conform
with the stated type of protection.
Safe area (non-explosion hazardous area)
Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices
located in safe areas still require a certificate if their outputs run into explosion hazardous
areas
Electrical symbols
Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied
Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be
applied or supplied
Grounded terminal
A grounded terminal, which as far as the operator is concerned, is already grounded by
means of an earth grounding system
Protective grounding (earth) terminal
A terminal which must be connected to earth ground prior to making any other
connection to the equipment
Equipotential connection (earth bonding)
A connection made to the plant grounding system which may be of type e.g. neutral star
or equipotential line according to national or company practice
Temperature resistance of the connection cables
States, that the connection cables must be resistant to a temperature of at least 65 °C.
EX
EX
t > 65°C
1 Safety instructions

Promonitor NRF560
6Endress+Hauser
2 Identification
2.1 Device designation
2.1.1 Nameplate
The following technical data are given on the instrument nameplate:
ATEX Approval Type Ex d
IECEx Approval Type Ex d
Order code
Serial number
Power supply
Manufacturing date
Test date
Tester
Certification number
Certification number
Certification number
Order code
Ser. no.
Supply
NP-2465-7
IP67, NEMA 4X
ZELM 03 ATEX 0154 X
IIC T4
ATEX II 2G
Ambient temperature: -20 ~ +60
Ex d
XA00586G-A/08
Manufacturing date
Test date
Test e r
Only read level when
indication "BAL" is present.
Certification no.
Tank ID

PROMONITOR NRF560
0044
Made in Japan
Yamanashi 406-0846
Endress+Hauser Yamanashi Co.,Ltd.
Warning: Do not open the cover when energized.
1
2
3
4
5
6
7
8
9
Order Code
Ser. No
Supply
NP-2622
IP67, NEMA 4X
IECEx ZLM 11.0010X
IIC T4 Gb
Ambient Temperature: -20 ~ 60 °C
Ex d
XA00664G-A/08
Only read level when
indication "BAL" is
0044
PROMONITOR NRF560
Warning: Do not open the cover when energized.
Made in Japan
Yamanashi 406-0846
Endress+Hauser Yamanashi Co.,Ltd.
Manufacturing date
Test date
Test e r
Certification no.
Tank ID
Order code
1
2
3
4
5
6
7
8
9
Serial number
Power supply
Manufacturing date
Test date
Tester
NMi W&M Certification number
PTB W&M Certification number
PTB W&M Certification number
2 Identification

Promonitor NRF 560
Endress+Hauser 7
FM Approval
TIIS Approval
Order code
Ser. no.
NP-2348-4
Input rated
Input
Manufacturing date
Ambient temperature -20 ~ +60 ℃
Warning: Keep cover tight while circuits are alive.
Caution: Use supply wires suitable for 70℃
minimum.
Caution: A seal shall be installed within 50 mm of the enclosure.
PROMONITOR NRF560
XP Class I, Div. 1, Gp. A, B, C, D ;
DIP Clsss II, III, Div. 1, Gp. E, F, G ;
Temperarure class T4
APPROVED
FM
NEMA 4X, IP67
Ambient temperature: -20 ~ +60 ℃
Made in Japan
Yamanashi 406-0846
Endress+Hauser Yamanashi Co.,Ltd.
Order code
Serial number
Input rated
Input
Only read level when
indication "BAL" is present.
Cetification no.
Tank ID
Order code
Ser. no.
㒐῜ဳᑼ㧦
Ex proof model:
㒐῜᭴ㅧ㧦
Protection class :
⼊๔㧦
࡮ 㔚Ḯㆤᢿᓟޔ30⑽એߚߞߡ߆ࠄኈེߩ⬄ࠍ㐿ߌߡߊߛߐ޿ޕ
࡮⸵ኈ󰶘ᐲ70એߩࠤ࡯ࡉ࡞ࠍ૶↪ߒߡߊߛߐ޿ޕ
Warning
䊶After de-energizing, delay
30 sec. before opening the cover.
䊶Use heat-resistant cable 70㷄or more.
NP-2211-3
!
!
ψ
+20'/#:
๟࿐󰶘ᐲ㧦-20 㨪+60 
Ambient temp.
Ṷ▚ಣℂⵝ⟎Tank side monitor
ቯᩰ/ Rating
㔚ޓḮ
Power supply :ޓ
࠺ࠫ࠲࡞ㅢାାภ(1): DC 24 V 100 mA
Digital signal(1):
࠺ࠫ࠲࡞ㅢାାภ(2): DC 24 V 24 mA
Digital signal(2):
ࠕ࠽ࡠࠣାภ:ޓޓ DC 2 V 0.2 W
Analog signal(2):
⵾ㅧᣣManufacturing date:
ỺὅἛἾἋἡỸἈὊޛషఇࡸ˟ᅈ
Yamanashi 406-0846
Made in Japan
Endress+Hauser Yamanashi Co.,Ltd.
PROMONITOR NRF560
Test date
Test e r
1
2
3
4
5
6
7
8
9
10
11
12
NMi㩷W&M
PTB㩷W&M
PTB㩷W&M
8
9
10
11
12
TANK ID
Order code
Serial number
Ex proof model
Protection class
Power supply
Manufacturing date
Certification number
Certification number
Certification number
Test date
Tester
2 Identification

Promonitor NRF560
8Endress+Hauser
CSA Approval
Order code
Ser. no.
NP-2344-4
Type 4X, IP67
Input rated
Input
XP Class I, Div. 1, Gp. C, D ;
DIP Clsss II, Div. 1, Gp. E, F, G ; Class III.
Temperarure class T4
R
216422
PROMONITOR NRF560
Ambient temperature: -20 ~ +60 
Warning: Keep cover tight while circuits are alive.
Caution: Use supply wires suitable for 70
minimum.
Caution: A seal shall be installed within 50 mm of the enclosure.
Manufacturing date
Ambient temperature -20 ~ +60 
Made in Japan
Yamanashi 406-0846
Endress+Hauser Yamanashi Co.,Ltd.
1
2
3
4
Input
Order code
Serial number
Input rated
2 Identification

Promonitor NRF 560
Endress+Hauser 9
2.2 Product structure
2.2.1 Promonitor NRF560
010 Approval
0 Weather proof, IP67 NEMA 4X
1 TIIS Ex d IIB T4
4 FM XP Cl.I, Div.1, Gr.A-D
5 CSA Cl.I, Div.1, Gr.A-D
6 ATEX II 2G Ex d IIC T4
8 ATEX II 2G Ex d IIC T4, NMi
F IECEx, Ex d IIC T4 Gb
9 Special version, TSP-no, to be spec.
020 Cable Entry
A2xthreadG1/2
B2xthreadNPT1/2
D2xthreadM20
Y Special version, TSP-no, to be spec.
030 Power Supply
3 85-264VAC, 50/60Hz
4 20-62VDC, 20-55VAC, 50/60Hz
9 Special version, TSP-no, to be spec.
040 Mounting Bracket
0 not selected
1selected
9 Special version, TSP-no, to be spec.
050 Colour
0blue
9 Special version, TSP-no, to be spec.
NRF560- Complete product designation
2 Identification

Promonitor NRF560
10 Endress+Hauser
2.3 Scope of delivery
Caution!
It is essential to follow the instructions concerning the unpacking, transport and storage of measuring
instruments given in the chapter "Incoming acceptance, transport, storage" on.
The scope of delivery consists of:
• Assembled instrument
• Accessories (Mounting Bracket)
Accompanying documentation:
• Operating manual (this manual)
• Safety instructions
2.4 Supplied documentation
2.5 Certificates and approvals
CE marks, declaration of conformity
The instrument is designed to meet state-of-the-art safety requirements, has been tested and left the factory in
a condition in which it is safe to operate. The instrument complies with the applicable
standards and regulations in accordance with EN 50014 "Electrical apparatus for potentially
explosive atmospheres-General requirements". The instrument described in this manual thus
complies with the statutory requirements of the EG directives. Endress+Hauser confirms the successful testing
of the instrument by affixing to it the CE mark.
2.6 Registered trademarks
HART®
Registered trademark of HART®Communication Foundation, Austin, USA
Document Designation Content/Remarks
BA00425G Operating manual describes installation, commissioning operating and mainte-
nance of the Promonitor NRF560.
XA00664G Safety Instructions only for instrument versions approved for use in explosion haz-
ardous areas; the nameplate specifies, which of these docu-
ments is relevant for your instrument version
2 Identification