Keysight Technologies E36100B Series Service manual

Operating and
Service Guide
E36100B Series
Programmable
DC Power Supplies

Notices 6
Copyright Notice 6
Manual Part Number 6
Edition 6
Published by 6
Warranty 6
Technology Licenses 6
U.S. Government Rights 7
Waste Electrical and Electronic Equipment (WEEE) 7
Declarations of Conformity 7
Safety Information 8
Safety and Regulatory Information 9
Safety Considerations 9
Safety Symbols 10
Regulatory Markings 11
South Korean Class A EMC declaration: 11
Safety and EMC Requirements 11
Environmental Conditions 12
1 Getting Started 13
Introduction 14
Front panel 14
Rear panel 15
Display 16
Dimension diagram 17
Setup the instrument 17
Options and Fuse Information 18
Ensure the correct AC input voltage and fuse settings 18
Programming Ranges 20
Table of programming and readback resolutions 20
Extending the Voltage Range and Current Range 21
Series connections 21
Parallel connections 21
Front Panel Operation 22
Configure the LAN interface 22
Set voltage and current 23
Specify 2- or 4-wire measurement 23
Configure Overcurrent Protection (OCP) and Overvoltage Protection (OVP) 24
Clear an OCP or OVP event 24
Clear an overtemperature protection (OTP) event 25
Lock and unlock the front panel 25
Save or recall the instrument's state 26
Configure the Power-on State 26
Read error codes 26
Remote Control 27
Keysight IOLibraries Suite 27
E36100B Series Web interface 27
Technical connection details 29
Rack Mounting the Instrument 30
Rack mounting a single instrument 30
Rack mounting multiple instruments side-by-side 30
Keysight E36100B Series Operating and Service Guide 2

2 SCPI Programming 32
Introduction to the SCPI Language 33
Command format used in this manual 34
Command separators 35
Using the MIN and MAX parameters 35
Querying parameter settings 35
SCPI command terminators 36
IEEE-488.2 common commands 36
SCPI parameter types 36
Error Messages 38
Error codes 38
SCPI Status Registers 42
What is an event register? 42
What is an enable register? 42
Standard Event Status Enable Register 43
Operation Status Register 43
Questionable Register 43
APPLy Subsystem 45
APPLy <voltage>| DEFault | MINimum | MAXimum[,<current>| DEFault | MINimum | MAXimum]APPLy? 45
CALibration Subsystem 46
CALibration:COUNt? 46
CALibration:CURRent[:DATA][:HIGH] <value> 46
CALibration:CURRent[:DATA]:LOW <value> 46
CALibration:CURRent:LEVel[:HIGH] MINimum|MAXimum 46
CALibration:CURRent:LEVel:LOW MINimum|MAXimum 46
CALibration:STATe <state>,<code>CALibration:STATe? 46
CALibration:STRing "<string>"CALibration:STRing? 47
CALibration:VOLTage[:DATA] <value> 47
CALibration:VOLTage:LEVel MINimum|MAXimum 47
CURRent Subsystem 48
[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude] <current> | MINimum | MAXimum |UP | DOWN
[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]? [MINimum | MAXimum] 48
[SOURce:]CURRent[:LEVel][:IMMediate]:STEP[:INCRement] <current> | DEFault[SOURce:]CURRent[:LEVel]
[:IMMediate]:STEP[:INCRement]? [DEFault] 48
[SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude] <current> | MINimum | MAXimum[SOURce:]CURRent
[:LEVel]:TRIGgered[:AMPLitude]? [MINimum | MAXimum] 48
[SOURce:]CURRent:PROTection:CLEar 48
[SOURce:]CURRent:PROTection:DELay[:TIME] <time> | MINimum |MAXimum[SOURce:]CURRent:PROTec-
tion:DELay[:TIME]? [MINimum |MAXimum] 48
[SOURce:]CURRent:PROTection:STATe ON|1|OFF|0[SOURce:]CURRent:PROTection:STATe? 48
[SOURce:]CURRent:PROTection:TRIPped? 48
DISPlay Subsystem 49
DISPlay[:WINDow]:TEXT:CLEar 49
DISPlay[:WINDow]:TEXT[:DATA] "<string>"DISPlay[:WINDow]:TEXT[:DATA] 49
DISPlay[:WINDow][:STATe] ON | 1 | OFF | 0DISPlay[:WINDow][:STATe]? 49
IEEE-488 Subsystem 50
*CLS 50
*ESE <enable value>*ESE? 50
*ESR? 50
*IDN? 50
*OPC*OPC? 51
3Keysight E36100B Series Operating and Service Guide

*OPT? 51
*PSC 0|1*PSC? 51
*RST 51
*RCL <state>*SAV <state> 51
*SRE <enable value>*SRE? 52
*STB? 52
*TRG 52
*TST? 52
*WAI 52
MEASure Subsystem 53
MEASure:CURRent[:DC]? 53
MEASure[:VOLTage][:DC]? 53
OUTPut Subsystem 54
OUTPut[:STATe] ON |1 | OFF |0OUTPut[:STATe]? 54
OUTPut:PROTection:CLEar 54
OUTPut:PON:STATe RST|RCL0|RCL1|RCL2|RCL3|RCL4|RCL5|RCL6|RCL7|RCL8|RCL9|OUTPut:PON:STATe? 54
STATus Subsystem 55
STATus:OPERation:[EVENT]? 55
STATus:OPERation:CONDition? 55
STATus:OPERation:ENABle <value> 55
STATus:PRESet 55
STATus:QUEStionable:CONDition? 55
STATus:QUEStionable:ENABle <enable value>STATus:QUEStionable:ENABle? 56
STATus:QUEStionable[:EVENt]? 56
SYSTem Subsystem 57
SYSTem:ERRor[:NEXT]? 57
SYSTem:LOCal 57
SYSTem:REMote 57
SYSTem:RWLock 58
SYSTem:SECurity:IMMediate 58
SYSTem:VERSion? 58
Triggering Commands 59
ABORt 59
INITiate[:IMMediate] 59
INITiate:CONTinuous ON | 1 | OFF | 0INITiate:CONTinuous? 59
*TRG 59
TRIGger[:SEQuence]:DELay <seconds> MINimum | MAXimumTRIGger[:SEQuence]:DELay? [MINimum |
MAXimum] 59
TRIGger[:SEQuence]:SOURce BUS | IMMediateTRIGger[:SEQuence]:SOURce? 59
VOLTage Subsystem 60
[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude] <voltage>|MINimum|MAXimum|DEFault
[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]? [MINimum | MAXimum] 60
[SOURce:]VOLTage[:LEVel][:IMMediate]:STEP[:INCRement] <numeric value>|DEFault[SOURce:]VOLTage
[:LEVel][:IMMediate]:STEP[:INCRement]? [DEFault] 60
[SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude] <voltage>|MIN|MAX[SOURce:]VOLTage[:LEVel]:TRIGgered
[:AMPLitude]? [MIN|MAX] 60
[SOURce:]VOLTage:PROTection:CLEar 60
[SOURce:]VOLTage:PROTection:STATe ON|1|OFF|0[SOURce:]VOLTage:PROTection:STATe? 60
[SOURce:]VOLTage:PROTection:TRIPped? 60
[SOURce:]VOLTage:PROTection[:LEVel] <voltage>|MINimum | MAXimum[SOURce:]VOLTage:PROTection
[:LEVel]? [MINimum|MAXimum] 60
[SOURce:]VOLTage:SENSe[:SOURce] INTernal | EXTernal 61
Keysight E36100B Series Operating and Service Guide 4

3 Service and Support 62
Service and Repair 63
Types of service available 63
Cleaning and handling 63
Troubleshooting 64
Self-test procedures 65
To replace the power-line fuse 65
User replaceable parts 65
Performance Verification 66
Recommended test equipment 66
Test considerations 66
Measurement techniques 67
Setup for most tests 67
Constant Voltage (CV) verification 68
Constant Current (CC) verification 75
Test Record Forms 78
Test Record Form - Keysight E36102B 78
Test Record Form - Keysight E36103B 80
Test Record Form - Keysight E36104B 82
Test Record Form - Keysight E36105B 84
Test Record Form - Keysight E36106B 86
Calibration Adjustment Procedures 88
Closed–case electronic calibration 88
Calibration interval 88
Calibration adjustment process 88
Calibration security 89
Calibration count 90
Calibration message 90
Saving calibration data 90
Calibration auto save 90
Calibration procedure 90
Save the calibration data 92
Specifications and Typical Characteristics 92
5Keysight E36100B Series Operating and Service Guide

Notices
Copyright Notice
© Keysight Technologies, 2017-2018
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or
translation into a foreign language) without prior agreement and written consent from Keysight Technologies as
governed by United States and international copyright laws.
Manual Part Number
E36100-90002
Edition
Edition 3, July 2018
Published by
Keysight Technologies
Bayan Lepas Free Industrial Zone
11900 Penang
Malaysia
Warranty
THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, KEYSIGHT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, WITH REGARD TO THIS MANUAL
AND ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYSIGHT SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT OR OF ANY INFORMATION CONTAINED HEREIN. SHOULD KEYSIGHT AND
THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN THIS
DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT
SHALL CONTROL.
Technology Licenses
The hardware and/or software described in this document are furnished under a license and may be used or copied
only in accordance with the terms of such license.
Keysight E36100B Series Operating and Service Guide 6

U.S. Government Rights
The Software is “commercial computer software,” as defined by Federal Acquisition Regulation (“FAR”) 2.101.
Pursuant to FAR 12.212 and 27.405-3 and Department of Defense FAR Supplement (“DFARS”) 227.7202, the U.S.
government acquires commercial computer software under the same terms by which the software is customarily
provided to the public. Accordingly, Keysight provides the Software to U.S. government customers under its
standard commercial license, which is embodied in its End User License Agreement (EULA), a copy of which can be
found at http://www.keysight.com/find/sweula. The license set forth in the EULA represents the exclusive authority
by which the U.S. government may use, modify, distribute, or disclose the Software. The EULA and the license set
forth therein, does not require or permit, among other things, that Keysight: (1) Furnish technical information
related to commercial computer software or commercial computer software documentation that is not customarily
provided to the public; or (2) Relinquish to, or otherwise provide, the government rights in excess of these rights
customarily provided to the public to use, modify, reproduce, release, perform, display, or disclose commercial
computer software or commercial computer software documentation. No additional government requirements
beyond those set forth in the EULA shall apply, except to the extent that those terms, rights, or licenses are explicitly
required from all providers of commercial computer software pursuant to the FAR and the DFARS and are set forth
specifically in writing elsewhere in the EULA. Keysight shall be under no obligation to update, revise or otherwise
modify the Software. With respect to any technical data as defined by FAR 2.101, pursuant to FAR 12.211 and
27.404.2 and DFARS 227.7102, the U.S. government acquires no greater than Limited Rights as defined in FAR
27.401 or DFAR 227.7103-5 (c), as applicable in any technical data.
Waste Electrical and Electronic Equipment (WEEE)
This product complies with the WEEE Directive) marketing requirement. The affixed product label (see below)
indicates that you must not discard this electrical/electronic product in domestic household waste.
Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as
“Monitoring and Control instrumentation” product. Do not dispose in domestic household waste.
To return unwanted products, contact your local Keysight office, or see
about.keysight.com/en/companyinfo/environment/takeback.shtml for more information.
Declarations of Conformity
Declarations of Conformity for this product and for other Keysight products may be downloaded from the Web. Go
to https://regulations.about.keysight.com/DoC/default.htm. You can then search by product number to find the
latest Declaration of Conformity.
7Keysight E36100B Series Operating and Service Guide

Safety Information
A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed
or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the
indicated conditions are fully understood and met.
A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly per-
formed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated con-
ditions are fully understood and met.
Keysight E36100B Series Operating and Service Guide 8

Safety and Regulatory Information
Safety Considerations
The following general safety precautions must be observed during all phases of operation, service, and repair of this
instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates
safety standards of design, manufacture, and intended use of the instrument. Keysight Technologies assumes no
liability for the customer's failure to comply with these requirements.
BEFORE APPLYING POWER
– Verify that the product is set to match the available line voltage and that the correct fuse is installed. Use the label
on the bottom of the instrument to configure the power. See Options and Fuse Information for additional
details.
GROUND THE INSTRUMENT
This product is a Safety Class I instrument (provided with a protective earth terminal). To minimize shock hazard, the
instrument chassis and cabinet must be connected to an electrical ground. The instrument must be connected to
the AC power supply mains through a three-conductor power cable, with the third wire firmly connected to an elec-
trical ground (safety ground) at the power outlet. Any interruption of the protective(grounding) conductor or dis-
connection of the protective earth terminal will cause a potential shock hazard that could result in personal injury. If
the instrument is to be energized via an external autotransformer for voltage reduction, be certain that the auto-
transformer common terminal is connected to the neutral (earthed pole) of the AC power lines (supply mains).
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE OR WET ENVIRONMENTS
Do not operate the device around flammable gases or fumes, vapor, or wet environments.
DO NOT OPERATE DAMAGED OR DEFECTIVE INSTRUMENTS
Instruments that appear damaged or defective should be made inoperative and secured against unintended oper-
ation until they can be repaired by qualified service personnel.
DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT
Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized
modification to the instrument. Return the instrument to a Keysight Technologies Sales and Service Office for ser-
vice and repair to ensure that safety features are maintained. To contact Keysight for sales and technical support,
refer to the support links on the following Keysight website: www.keysight.com/find/assist (worldwide contact
information for repair and service).
BE CAUTIOUS WHEN DEALING WITH OUTPUTS ABOVE 60 VDC
Always be cautious when dealing with output voltage above 60 VDC. Such voltage poses electrical shock hazard.
USE THE POWER CORD PROVIDED
Use the device with the power cord provided with the shipment.
USE THE DEVICE AS SPECIFIED
If the device is used in a manner not specified by manufacturer, the device protection may be impaired.
DO NOT BLOCK VENTILATION HOLES
Do not block any of the ventilation holes of the device.
9Keysight E36100B Series Operating and Service Guide

OBSERVE ALL DEVICE MARKINGS BEFORE CONNECTING TO DEVICE
Observe all markings on the device before connecting any wiring to the device.
TURN DEVICE OFF BEFORE CONNECTING TO OUTPUT TERMINALS
Turn off the device power before connecting to the output terminals.
ENSURE COVER IS SECURED IN PLACE
Do not operate the device with the cover removed or loosened.
CLEAN WITH SLIGHTLY DAMPENED CLOTH
Clean the outside of the instrument with a soft, lint-free, slightly dampened cloth. Do not use detergent, volatile
liquids, or chemical solvents.
Safety Symbols
Symbol Meaning
Caution, risk of danger (refer to the manual for specific Warning or Caution information).
Protective earth (ground) terminal.
Frame or chassis (ground) terminal.
In position of bi-stable push control.
Out position of bi-stable push control.
Alternating current (AC).
Direct current (DC).
Plus, positive polarity.
Minus, negative polarity.
The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the like, which, if not correctly performed
or adhered to, could result in personal injury. Do not proceed beyond a WARNING sign until the indicated conditions are fully
understood and met.
The CAUTION sign denotes a hazard. It calls attention to an operating procedure, or the like, which, if not correctly
performed or adhered to, could result in damage to or destruction of part or all of the product. Do not proceed beyond
CAUTION sign until the indicated conditions are fully understood and met.
The NOTE sign denotes important information. It calls attention to a procedure, practice, condition or the like, which is
essential to highlight.
Keysight E36100B Series Operating and Service Guide 10

Regulatory Markings
Symbol Description
The RCM mark is a registered trademark of the Australian Communications and Media Authority.
The CE mark is a registered trademark of the European Community. This CE mark shows that the product com-
plies with all the relevant European Legal Directives.
ICES/NMB-001 indicates that this ISM device complies with the Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.
ISM GRP.1 Class A indicates that this is an Industrial Scientific and Medical Group 1 Class A product.
This symbol indicates the time period during which no hazardous or toxic substance elements are expected to
leak or deteriorate during normal use. Forty years is the expected useful life of the product.
This symbol is a South Korean Class A EMC Declaration. This is a Class A instrument suitable for professional
use and in electromagnetic environment outside of the home.
The CSA mark is a registered trademark of the Canadian Standards Association.
South Korean Class A EMC declaration:
Information to the user:
This equipment has been conformity assessed for use in business environments. In a residential environment this
equipment may cause radio interference.
– This EMCstatement applies to the equipment only for use in business environment.
사용자안내문
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가
정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
–사용자 안내문은 “업무용 방송통신기자재”에만 적용한다.
Safety and EMC Requirements
This power supply is designed to comply with the following safety and EMC (Electromagnetic Compatibility)
requirements:
– Low Voltage Directive (2014/35/EU)
– EMC Directive (2014/30/EU)
– IEC61010-1:2010/EN61010-1:2010
– IEC61326-1:2012/EN61326-1:2013
11 Keysight E36100B Series Operating and Service Guide

Environmental Conditions
The E36100B Series is designed for indoor use and in an area with low condensation. The table below shows the
general environmental requirements for this instrument.
Environmental condition Requirement
Temperature Operating condition: 0 °C to 40 °C
Storage condition: –20 °C to 70 °C
Humidity Operating condition: Up to 80% RH at 40 °C (non-condensing)
Storage condition: Up to 90% RH at 65 °C (non-condensing)
Altitude Up to 2000 m
Pollution degree 2
Installation category (AC input) Category II
12 Keysight E36100B Series Operating and Service Guide

1 Getting Started
Introduction
Options and Fuse Information
Programming Ranges
Extending the Voltage Range and Current Range
Front-panel Operation
Remote Control
Rack Mounting the Instrument
This chapter describes the general operating information for the
E36100B Series programmable DC power supplies.
13 Keysight E36100B Series Operating and Service Guide

Introduction
The Keysight E36100B Series is a series of DC bench and system power supplies with the following features and
characteristics:
– Single output up to 100 V or 5 A
– Small size: two rack-units (2U), 1/4-rack form factor
– Remote sense capability
– Intuitive front panel
– High visibility organic light emitting diode (OLED)display
– High performance functionality: accuracy, transient response, and rise/fall time
– LAN (LXICore) and USB interfaces for remote programming with SCPIS
Front panel
Item Description
A Tough carrying handle
B Information-packed, high-contrast OLED display; easily viewable even from sharp angles
C Rotary knob for quick and easy configuration
D Fast voltage/current setting and front-panel electronic calibration
E Menu key opens intuitive user interface
F Front-panel lock prevents accidental changes during tests
G Output enable/disable switch to protect your DUT quickly
H Dual-position power switch
I Sense terminals
J Output terminals
K Earth ground reference point
Keysight E36100B Series Operating and Service Guide 14

Rear panel
The rear panel includes the power input, standard LAN and USB ports, and a security slot. Always use the power
cord that arrived with the instrument or one with equivalent ratings.
15 Keysight E36100B Series Operating and Service Guide

Display
The power supply's front panel features a high-visibility OLED display.
The upper left corner of the display shows either CV or CC to indicate that the instrument is in constant voltage or
constant current mode. Below that is either 2W or 4W, to indicate whether 2-wire (normal) or 4-wire (remote
sensing) measurement is in use. The right side of the display shows the output voltage and current (when the output
is enabled), and the voltage and current settings are shown near the bottom of the screen.
The very bottom of the screen can show arrows, each of which represents a different annunciator.
Label Meaning
ERR An error has occurred.
OCP An overcurrent protection event has occurred.
OVP An overvoltage protection event has occurred.
RMT The instrument is being programmed remotely.
LCK The front panel is locked.
Keysight E36100B Series Operating and Service Guide 16

Dimension diagram
Setup the instrument
Place the instrument's feet on a flat, smooth horizontal surface. Connect output and sense leads to the front panel,
being careful not to short the leads together. Attach the power cable to the rear panel, then plug it into main power.
Connect LAN or USB cables as desired, and you may also secure the instrument with a security lock cable.
Before disconnecting cables and cords from the instrument, turn the instrument off using the front-panel power
switch and disconnect from the supply source by unplugging the detachable power cord.
17 Keysight E36100B Series Operating and Service Guide

Options and Fuse Information
Ensure you order the proper instrument option for the mains power that will be used for the instrument.
Options 0EM, 0E3, and 0E9 determine which power-line voltage is selected at the factory. The default is configured
for 230 VAC ± 10%, 47-63 Hz input voltage (option 0E3).
Option Description
0EM 115 VAC ± 10%, 47-63 Hz input voltage
0E3 230 VAC ± 10%, 47-63 Hz input voltage
0E9 100 VAC ± 10%, 47-63 Hz input voltage
Input power for E36102B, E36103B, E36104B, E36105B, and E36106B is 200 VA maximum.
Ensure the correct AC input voltage and fuse settings
Use the proper switch settings
To change the input AC voltage selector on the power supply, use the two AC selector switches on the underside of
the power supply as shown.
For example, to select 230 V, slide the left switch to the left and the right switch to the right, as illustrated in the
diagram below the switches.
To select 115 V, slide both switches to the right, and to select 100 V, slide the two switches towards each other.
Keysight E36100B Series Operating and Service Guide 18

Use the correct fuse
You must use a time delay 2-A fuse for 100- and 115-VAC inputs, and a time delay 1-A fuse for 230-VAC inputs:
Part Number Description Manufacturer Application
2110-1639 Fuse 1 A, 250 V Time-delay Littelfuse 230-V line voltage
2110-1640 Fuse 2 A, 250 V Time-delay 100- and 115-V line voltage
To configure the correct fuse, follow the three steps shown below:
Pull the fuse holder out of the
power supply.
Remove and insert the proper
fuse into the fuse holder.
Re-insert the fuse holder into the
power supply.
19 Keysight E36100B Series Operating and Service Guide

Programming Ranges
The following table shows the maximum voltage, current, and power that can be programmed for each model. The
DEFault voltage is always 0 V.
Model Max voltage (V) Max current (A) Max power (W)
E36102B 6 5.0 30
E36103B 20 2.0 40
E36104B 35 1.0 35
E36105B 60 0.6 36
E36106B 100 0.4 40
Note that the actual programmable values are 3% above these nominal values, but instrument specifications are
only guaranteed up to the values shown in this table.
Table of programming and readback resolutions
Model Voltage programming Voltage readback Current programming Current readback Small current readback
E36102B 0.001 V 0.001 V 0.001 A 0.001 A 0.001 mA
E36103B 0.001 V 0.001 V 0.001 A 0.001 A 0.001 mA
E36104B 0.001 V 0.001 V 0.001 A 0.001 A 0.001 mA
E36105B 0.001 V 0.01 V 0.001 A 0.0001 A 0.001 mA
E36106B 0.001 V 0.01 V 0.001 A 0.0001 A 0.001 mA
Keysight E36100B Series Operating and Service Guide 20