Kid’s Comfort Manhattan JR-4802 User manual

WARNING: Failure to follow these
warnings and the assembly instructions could
result in serious injury or death.
WARNING: Read all instructions be-
fore assembling crib. Keep instructions for fu-
ture use.
WARNING: Infants can suffocate on
soft bedding. Never add a pillow or comforter.
Never place additional padding under an in-
fant.
 To reduce the risk of SIDS, pediatricians recommend healthy infants
be placed on their backs to sleep, unless otherwise advised by your phy-
sician.
 Strings can cause strangulation ! DO NOT place items with a string
around a child's neck, such as hood strings or pacifier cords. DO NOT
suspend strings over a crib or attach strings to toys.
 To help prevent strangulation tighten all fasteners. A child can trap
parts of the body or clothing on loose fasteners.
 DO NOT place crib near window where cords from blinds or drapes
may strangle a child.
 When child is able to pull to a standing position, set mattress to low-
est position and remove bumper pads, large toys, and other objects that could serve as steps for climbing out.
 When child is able to climb out or reaches the height of 35 in.(90 cm), the crib shall no longer be used.
 Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assem-
bly and frequently during use. DO NOT use crib if any parts are missing, damaged or broken. Contact J&R
Woodworking for replacement parts and instructional literature if needed. DO NOT substitute parts.
 Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
 Infants can suffocate in gaps between crib sides and a mattress that is too small. Use a mattress that is at least
27 1/4 x 51 5/8 with a thickness not exceeding six inches.
Follow warnings on all products in a crib.
MAINTENANCE AND CLEANING
 Caution: Periodically check the safety of your crib by making certain all screws, nuts and bolts are tightened
securely. Call J&R Woodworking to replace any broken or missing parts. Do not substitute parts.
 If refinishing, use a non toxic finish specified for children's products.
 Your crib may be cleaned using a damp cloth with mild soap or a soft dry cloth.
Avoid using furniture polish or cleaning agents that may be hazardous to children.
OPERATION AND STORAGE
 This crib is guaranteed to meet all federal and state standards and will provide you with many years of service
provided you adhere to the guidelines for assembly, maintenance and operation.
 Never aim a vaporizer or heating vent directly at the crib as this will damage the crib.
Put these instructions in your hardware bag when done assembling the crib. Insert hardware bag into pouch on
crib spring for further use.
Kid’s Comfort
Manhattan Crib
Model #JR-4802
 8—1 1/4” Connecter Bolts (to fasten
mattress support)
 24- Internal tooth lock washers (for all
connecter bolts used on assembly of crib.)
 8 –3 1/4” Connecter Bolts
 8 –2 1/2” Connecter Bolts
 1 - 4 mm Allen Wrench
 1—Assembly Instruction
Note : Parts diagram on next page.
Kid’s Comfort Furniture
Your Source for Youth Furniture
4864 County Road 120
Millersburg OH 44654
330-893-0713

InstrucƟons for assembling ManhaƩan Crib
TOOLS & PARTS
NEEDED FOR STEP 1
1—4mmAllenWrench
8—Internal‐toothLockWashers
 Aachheadboardpoststoheadboardbyusing4–31/4”connecterbolts
withlockwashersincluded.IMPORTANT !!! USE LOCK WASHERS PROVIDED
 Repeatsamestepforothersidepanel.
 Tightenconnecterboltswithallenwrenchprovided.Makesuretopofsidesareevenwithtopofposts
 Makesureallconnecterboltsareghtenedsnugly.(IMPORTANT!!! DO NOT OVERTIGHTEN)

Step 1 = Aachingpoststoheadboard&footboard
8—31/4”ConnecterBolts

InstrucƟons for assembling ManhaƩan Crib
TOOLS & PARTS
NEEDED FOR STEP 2
1—4mmAllenWrench
4—Internal‐toothLockWashers

 Aachoneendpaneltoheadboardpostsbyusing2–21/2”connecterbolts
withlockwashersincluded.IMPORTANT !!! USE LOCK WASHERS PROVIDED
 Repeatsamestepforotherendpanel.
 Tightenconnecterboltswithallenwrenchprovided.
 Makesureallconnecterboltsareghtenedsnugly.(IMPORTANT!!! DO NOT OVERTIGHTEN)

Maintenance and Cleaning
 Cauon:PeriodicallyCheckthesafetyofyourcribbymakingcertainallscrewsandnutsareghtenedsecure‐
ly.CallJ&RWoodworkingtoreplaceanybrokenormissingparts.Donotsubstuteparts.
 Yourcribmaybecleanedusingadampclothwithmildsoaporasodrycloth.
 Avoidusingfurniturepolishorcleaningagentsthatmaybehazardoustochildren.
 Ifrefinishing,useonlynon‐toxicfinishspecifiedforchildren’sproducts.
OperaƟon and Storage 
Thiscribisguaranteedtomeetallfederalandstatestandardsandwillprovidemanyyearsofserviceprovided
youadheretothefollowingguidelinesforassembly,maintenanceandoperaon.Neveraimorpointavaporizer
orhumidifierdirectlyatthecrib.Thewatervaporwillruinthefinishofthecrib,asitwouldanyotherfinepiece
offurniture.
ForpartsorassistancecallJ&RWoodworking.
DisassembleandStorage:
1.Removethecribmaress.
2.Followtheassemblyinstruconsinreverseorderstarngwithstep4.
3.Storeyourcribinacool,dryplace.

Step 2 = Aachingheadboardtoends
4—21/2”ConnecterBolts

8—INTERNALTOOTHLOCK
WASHERS
1—4mmALLENWRENCH
8—11/4”CONNECTERBOLTS
TOOLS & PARTS
NEEDED FOR STEP 3
 Aachcribmaressplaormtometalinsertsonwoodblockmountedoncribends.
 Use4—11/4”connecterboltswithlockwasherstoaacheachcornerofcribmaresssup‐
port.IMPORTANT !!! USE LOCK WASHERS PROVIDED
 Makesureallconnecterboltsareghtenedsnugly.(IMPORTANT!!! DO NOT OVERTIGHTEN)
(CAUTION !!! ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES BY 51 5/8 INCHES
WITH A THICKNESS NOT EXCEEDING 6 INCHES.
InstrucƟons for assembling ManhaƩan Crib
Step 3 = Aachingcribmaressplaormtocrib

TOOLS & PARTS
NEEDED FOR STEP 4
1—4mmAllenWrench
4—Internal‐toothLockWashers
4—21/2”ConnecterBolts
 Aachfootboardtoendpanelbyusing4–21/2”connecterboltswithlockwashersaached.IMPORTANT !!!
USE LOCK WASHERS PROVIDED
 Repeatsamestepforotherendpanel.
 Tightenconnecterboltswithallenwrenchprovided.
 Makesureallconnecterboltsareghtenedsnugly.(IMPORTANT!!! DO NOT OVERTIGHTEN)

Step 4 = Aachingfootboardtoends
InstrucƟons for assembling ManhaƩan Crib
Instructions for converting crib to youth bed
1—4mmAllenWrench
4—31/4”ConnecterBolts
4—Internal‐toothLock
Washers
Tools & Parts Needed to Convert
Crib into DayBed
 RemoveFootboardbyunscrewingthefourfront31/4”connecterboltsfromendsoffootboardposts.
 Movecribmaresssupporttoitslowestposion.
 Aachsafetyboardwithfour31/4”boltsprovidedbyinserngboltsthroughpostsandturningboltsintoinserts
inconversionboardsends.

8—21/2”ConnecterBolts
8—Internal‐toothLockWashers
1—4mmAllenWrench
TOOLS AND PARTS NEEDED TO
CONVERT CRIB TO FULL BED To Cover Holes...
 Removecribmaresssupport,conversionboard,andtwoendpanels.
 Aachbedrailstofootboardbyinserng21/2”connecterboltsthroughrailbracketsintoposts.
 Repeatsamestepstoaachheadboardasfootboard.
 Aachfourcrossslatsbyinserngcrossslats(providedwithyourrails)overdowelsthatareonrails
 Covertheexposedholesintheheadboard&footboardusingtheboltsasshowninthesketchabove.
4—11/4”CONNECTERBOLTS
InstrucƟons for converƟng daybed to full size bed