Kidsmill Up! User manual

Newborn Rocker - User manual AUS

INDEX

CONGRATULATIONS

WARNINGS

SAFETY MEASURES

MAINTENANCE

PARTS

INSTALLATION

USE

WARRANTY

IMPORTANT! RETAIN THESE INSTRUCTIONS FOR

FUTURE REFERENCE AND READ CAREFULLY

CONGRATULATIONS

Congratulations on the purchase of this Kidsmill Up! Rocker. This product meets

the most stringent safety requirements. Using this baby rocker can only be safe

when used according to these instructions. The child may be hurt if you do not

follow these instructions.

WARNINGPREVENT SERIOUS INJURY OR DEATH:

• WARNING - Never leave child unattended.

• WARNING - This product is not intended for unsupervised or prolonged periods

of sleep.

• WARNING - Always use restraint system.

• WARNING - Never use for a child able to sit up unassisted.

• FALL HAZARD: Child's activity may move rocker. Use only on oor. Never use on

any elevated surface.

• SUFFOCATION HAZARD: Never use on a soft surface (bed, crib, sofa, cushion), as

seat may tip over and cause suocation.

SAFETY MEASURES

• This reclined cradle is intended for children weighing up to 9 kg.

• Should your child need to sleep, then it should be placed in a suitable crib or bed.

• Do not use this infant rocker if any part is broken, torn or missing.

• Do not use accessories or replacement parts other than those approved by the

manufacturer.

MAINTENANCE

• We recommend cleaning this rocker using a damp cloth.

• Never use aggressive or abrasive cleaning agents because these can aect the

rocker and can also be detrimental to the health of your child.

• Ensure all locking devices work correctly and check the locks and ttings

regularly.

KIDSMILL Rocker UP!

PARTS

1. Screw 3x13 (2x)

8. Hex Key 4 (1x)

3. Screw M5(2x)

6. Housing (2x)

4. Dowel(2x)

5. Pin M6 (2x)

7. Set screw M6(2x)

2. Cilinder stop (2x)

9. Left part (1x)

10. Right part (1x)

11. Rod (1x)

13. Hex Key 3 (1x)

12. Rear section (1x)

ASSEMBLY

Step 3: Place the dowels (4) and the pins (5)

in the rear section (12) of the rocker.

12.

Step 2: Place the metal tension rod (11)

between the two sides (9+10) of the rocker

and tighten the screws (3) by hand.

10.

11.

Step 1: Screw (1) the cylinder stops (2) to

the left and right part (9+10) of the rocker.

INSTALLATION

Step 4b: Insert the housing (6) into the side

(9 + 10). Slide the pin (5) into the housing and

tighten the connection with the set screw (7).

Step 5: Make sure the rocker is leveled and

tighten the screws (3).

Step 4a: Attach the rear section(12) of the

rocker to the two sides (9+10).

10.

12.

2x 2x

USE

Step 1a: Slide the Up! Newborn seat on the

rocker from the upper side.

Step 2: To unlock the seat, pull up both

buttons, at the sides of the seat, at the same

time and slide the seat o the rocker.

Step 1b: Push the seat until it locks with a

clear audible "Click" on both sides.

'CLICK'

WARRANTY

Validity: 2 years from date of purchase.

The warranty is only valid in conjunction with proof of purchase. The warranty covers the

replacement of the entire product or parts when there a manufacturing defect. After the expiration

of the warranty there are costs attached to any repairs. The supplier takes no responsibility for any

damage or injury to persons, animals and belongings due to misuse of the harness or by failure to

follow the accompanying instructions.

Exclusion

All rights in respect of the guarantee and the responsibility of the supplier shall lapse if the product:

• Is dismantled by unauthorized persons;

• Is not properly used or stored.

Furthermore, all external damage to the product that does not aect the proper functioning is

excluded from the warranty.

WARRANTY FORM

Customer name: .........................................................................................................................................................

Order number: ............................................................................................................................................................

Notes: ...........................................................................................................................................................

.......................................................................................................................................................................

Quantity Damaged Missing

...................

................... ...................

Product:........................................................................................................................................................................

Article number:...........................................................................................................................................................

Serial number:............................................................................................................................................................

Part number (p. 4)