Kikusui PL02-TOS User manual

The PL02-TOS warning light unit indicates that a Kikusui withstanding
voltage tester, withstanding voltage and insulation resistance tester, or
electrical safety analyzer (hereafter referred to as the Tester) that has a
STATUS OUT (24 V) terminal is in a test state.
For your safety, be sure to check the warning light illumi-
nates before using it. Do not leave or use the PL02-TOS
with the cover removed or when the cover is broken.
Names of Parts
■Connecting to the connector
1Remove 10 mm of coating from
the tip of the wires.
2Insert a flat-blade screwdriver
into A, and open B.
3Insert the wire into B. Take care
to prevent the coating from becoming caught in B.
4Gently pull on the wire to confirm that it is securely connected.
OPERATION MANUAL
Warning Light Unit PL02-TOS
Part No. Z1-002-690, IA002883
Dec 2018
WARNING
Cover
Illuminates or blinks in red when power is input.
BLINK ON/OFF
Switch used to select illuminating or blinking of the warning
light. Turn the switch ON to set the warning light to blink.
AC/DC24V
Connector for the input power. There is no polarity.
A
B
Shank diameter: ø3; tip width: 2.6 mm
10 mm
Applicable wires
• Wire length Less than 3 m
•Solidwire ø0.4 to ø1.2 (AWG26 to 16)
• Stranded wire 0.3 mm2to 1.25 mm2(AWG22 to 16)
Element wire diameter ø0.18 or more

2PL02-TOS
Operating Procedure
Be sure to turn off the Tester before connecting the
wires.
1Connect the AC/DC24V connector of the PL02-TOS and the STA-
TUS OUT terminal of the Tester.
2Set the Tester so that a signal is output from the STATUS OUT termi-
nal when a test is in progress.
3The PL02-TOS is activated when a test is started on the Tester.
■Connection example
• A rubber magnet is attached to the bottom of the
PL02-TOS to fix it in place. However, do not place the
PL02-TOS on a slanted surface, uneven surface, or a
place with vibrations. The rubber magnet cannot with-
stand strong shock. Be careful not to drop the PL02-
TOS by carrying out acts such as yanking on the con-
nection cord. Such acts can damage the warning light.
• If the cover needs cleaning, gently wipe using a soft
cloth with water-diluted neutral detergent. Do not use
volatile solvents such as thinner or benzine.
WARNING
Tester
rear panel
Less than 3 m
PL02-TOS
STATUS OUT AC/DC24V
+
COM
CAUTION

PL02-TOS 3
Specifications
Power requirement
Nominal Voltage 24 V AC/DC
Allowable voltage range AC: 24 V± 10 %, DC: 20 V to 30 V
Current consumption
(24 Vdc)
55 mA
Maximum power
consumption
4 W
Installation location Indoors at an altitude of up to 2000 m
Environment
Operating
range
Temperature 0 °C 40 °C (32 °F to 104 °F)
Humidity 20 %rh to 80 %rh (No condensation)
Storage
range
Temperature -20 °C to 70 °C (-4 °F to 158 °F)
Humidity 90 %rh or less (No condensation)
Safety*1
*1. A custom order model does not apply to.
Complies with the requirements of the following standard.
IEC61010-1:1990-09 / A2:1995-07
(Class lll, Pollution degree 2*2 )
This equipment is designed to operate from overvoltage
category I.
*2. Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduc-
tion of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only non-
conductive pollution will occur except for an occasional temporary conductivity caused by
condensation.
Insulation resistance 30 MΩor more (500 Vdc)
[between the connector and chassis]
Withstand voltage 500 Vac, 1 minute, 2 mA or less
[between the connector and chassis]
Dimensions (largest section) 110 W x (160) H x 115 (120) D mm
(4.33 W x (6.30) H x 4.53 (4.72) D inch)
Weight Approx. 700 g (1.54 Ib)
Accessories Connection cord: 1 set (2.5 m)
Operation manual: 1 copy.

KIKUSUI ELECTRONICS COR
P.
The newest version of the manual can
be downloaded from Download service
of Kikusui website.
www.kikusui.co.jp/en
© 2002
1-1-3 Higashiyamata, Tsuzuki-ku, Yokohama,
224-0023, Japan
Tel: [phone]
Fax: [phone]