Kikusui LP01-TOS User manual

The LP01-TOS/LP02-TOS Test Probe is a dedicated probe for a KIKUSUI TOS6210/
TOS6200A/TOS6200/TOS6100 Earth Continuity Tester. Its convenient shape allows
faster connection to the device under test (DUT).
The LP01-TOS and LP02-TOS can measure until 30 A and 60 A respectively in the
earth continuity test.
• This product is designed to be used with a KIKUSUI Earth Continuity
Tester. Carefully read the warnings and precautions given in the Earth
Continuity Tester Operation Manual before attempting to use it.
Precautions for Use
■Be sure to connect the remote control cable.
•Never perform testing using the Tester START switch without the remote con-
trol cable.
■Never use the test probe with other earth continuity testers.
•The test probe is designed specifically for use with a KIKUSUI Earth Continu-
ity Tester. It cannot be used with other earth continuity testers, even if the
connector appears to be compatible.
■Never use the product at currents over the rated maximum current
•The rated maximum current (see Description *1 on page 7) of the probe is 30
Aac (LP01-TOS) or 60 Aac (LP02-TOS). Use at over currents may result in
fire.
■Never touch the contact pin immediately testing is completed.
•If the LP02-TOS is used more than 30 A, the contact pin will be high tempera-
tures. Never touch the contact pin immediately testing is completed. Touching
will result in getting burned.
■Handle the test probe attentively. Do not swing it around.
■Do not yank the test probe cable or drape it over any part of your body.
Part No. Z1-003-490, I0027201
Oct 2020
LP01-TOS/LP02-TOS
OPERATION MANUAL
TEST PROBE
NOTE

2LP01/02-TOS
Component Names and Functions
Figure shows the LP02-TOS.
START Switch
This is used to begin testing.
Depress the switch continuously
during testing. Releasing your fin-
ger from the switch will stop testing.
Contact Pin
Test current is delivered to this pin
contacting a test point of the DUT.
Holder
This part holds the contact pin.
OUTPUT LED
This red LED indicates that testing
is executing.
It turns on or off in response to the
on/off status of the TEST LED of
the Tester.
Remote Control Cable
Current Output Cable
LOW Test Lead
Voltage Measurement Cable

LP01/02-TOS 3
Inspection Before Starting
Always inspect and confirm the following items before beginning an actual test.
If any abnormality or failure is found in the “Inspection Before Starting,” immediately
stop using the test probe and contact your Kikusui distributor or agent for repairs.
■Test probe cable and LOW test lead
•Check for broken sheathing and loose or cracked connectors.
•Confirm electrical continuity.
■Start switch
•Confirm that the switch operates smoothly when pressed.
■Contact pin
•Check for any signs of damage.
•Check the pin for loose connection.
LP01-TOS
LP02-TOS
1.
2.
3.
The pin is correctly
attached.
The pin connection
is loose.
Pin adjustment
1. Turn the holder counter clockwise.
2. Turn the pin fully clockwise.
3. Turn the holder fully counter clockwise.

4LP01/02-TOS
Stop Use in the Event of Failure
In the following cases, the test probe is defective. To minimize hazards, immediately turn
off the POWER switch of the Tester and stop using the test probe.
•The OUTPUT LED does not light.
•The on/off status of the OUTPUT LED of the test probe is inconsistent
with that of the TEST LED on the Tester.
•The OUTPUT LED remains lit even when you release your finger from
the START switch.
•Implement measures so that no one can use the test probe until it
has been repaired.
•To minimize potential hazards, always contact your Kikusui distrib-
utor or agent for repairs.
WARNING

LP01/02-TOS 5
Connecting to the Earth Continuity Tester
•Improper terminal connections can result in inaccurate measure-
ments and burns or injury resulting from heat generated by con-
tact resistance at the terminals.
1. Turn off the POWER switch of the Tester.
2. Remove the short-circuit bars connecting the OUTPUT and SAMPLING ter-
minals.
3. Connect the LOW test lead to the LOW terminal of the Tester.
4. Connect the each cable of the test probe to the HIGH and REMOTE termi-
nal of the Tester.
Connecting the remote control cable starts or stops testing as indicated below:
Tester’s Panel Operation Operation of Test Probe
Starting test Disabled Depress the START switch.
Stopping test Press the STOP switch. Release your finger from the
START switch.
WARNING
To SAMPLING
HIGH terminal
Figure shows connections of the
TOS6210 with the LP02-TOS.
To the REMOTE terminal
To OUTPUT
HIGH terminal
To SAMPLING
LOW terminal
To OUTPUT
LOW terminal
TOS6210

6LP01/02-TOS
Test Procedure
•If the LP02-TOS is used more than 30 A, the contact pin will be
high temperatures. Never touch the contact pin immediately test-
ing is completed. Touching will result in getting burned.
•Be sure to connect the contact pin and the alligator clip to the
DUT. If the contact pin is removed or the clip is disconnected from
the DUT during testing, result in sparking and potentially damag-
ing the DUT.
•Configure the required test conditions for the Tester by referring to the opera-
tion manual.
•To obtain secure identification of FAIL judgment, turning on the FAIL MODE of
the Tester is recommended.
• Connect the test probe to the Tester according to the “Connecting to the Tes-
ter” item.
1. Connect the alligator clip of the LOW test lead to the protective conductor
terminal of the DUT.
2. Apply the contact pin of the test probe to the test point of the DUT.
3. Depress the START switch.
This causes the OUTPUT LED to light up; the test current flows from the con-
tact pin.
Do not remove the contact pin from the DUT during testing.
4. When testing is complete, lift your finger from the START switch.
Do not remove the contact pin from the DUT.
5. Confirm that the OUTPUT LED is not lit.
6. Remove the test probe from the DUT.
7. Disconnect the alligator clip of the LOW test lead from the DUT.
After completing all tests, turn off the POWER switch of the Tester.
WARNING
CAUTION
Testing from the protec-
tive conductor terminal
on the enclosure.
To stop testing, release your
finger from the START switch.
1. To the protective conductor terminal
2. To the test point
3.DepresstheSTART
switch.
The OUTPUT LED
lights up.
DUT

LP01/02-TOS 7
Maintenance
Periodic inspections and maintenance are required to maintain the product’s original
performance over the long term.
•Be sure to disconnect the test probe from the Tester before starting inspec-
tions or maintenance.
•Avoid volatile solvents such as thinner and benzene, which may discolor the
probe’s surface coating, erase printed characters, etc.
Cleaning
If the test probe becomes soiled, moisten a piece of soft cloth with a mild, dilute detergent
and gently wipe the probe.
Periodic Inspection
The cable of the test probe, contact pin, and LOW test lead are consumables. We
recommend an annual inspection by one of service engineers. To have an inspection
performed, contact your Kikusui distributor or agent.
Specifications
*1:The rated maximum voltage/current refers to the maximum voltage/
current the test probe is capable of handling within the given operating
temperature and humidity ranges.
LP01-TOS LP02-TOS
Rated maximum voltage (*1) 30 V
Rated maximum current (*1) 30 Aac 60 Aac
Residual resistance 10 m or less
Operating environment Indoor use, Altitude: up to 2000 m
Operating temperature and
relative humidity range
0 C to 40C
20 % to 80 % (no condensation)
Storage temperature and
relative humidity range
-20 C to 70 C
90 % or less (no condensation)
Insulation
resistance
Between contact
pin and signal cable
30 M or more (500 Vdc)
Withstanding
voltage
Between contact
pin and signal cable
500 Vac for 5 seconds, 2 mA or less
Cable length Approx. 2 m
Physical dimensions 28 (W) x 45.5 (H) x 226 (D) mm
Weight Approx. 500 g Approx. 700 g
Accessories LOW test lead: 1 (1.5 m)
Operation manual: 1 copy
Description

该标记为适用于在中华人民共和国销售的电子信息产品的环境保护使用期限。
只要遵守有关该产品的安全及使用注意事项，从制造年月起计算，在该年度内，就不
会对环境污染、人身、财产产生重大的影响。
产品的废弃请遵守有关规定。
产品的制造年月可以在以下网址中确认。
https://www.kikusui.co.jp/pi/
有毒有害物质或元素名称及含有标示
Name of hazardous materials and symbol of element
in the equipment and quantity
本表格依据 SJ/T 11364 的规定编制。
○ : 该部件所有均质材料的有毒有害物质的含量不超过 GB/T 26572 标准所规定的
极限值要求。
×: 该部件至少有一种均质材料的有毒有害物质的含量超过 GB/T 26572 标准所规
定的极限值要求。
环境保护使用期限
Environment-friendly Use Period
部件名称
有毒有害物质或元素
铅
Pb
汞
Hg
镉
Cd
六价铬
Cr(VI)
多溴联苯
PBB
多溴二苯醚
PBDE
LP01-TOS × ○ ○ ○ ○ ○
LP02-TOS × ○ × ○ ○ ○
KIKUSUI ELECTRONICS CORP.
www.kikusui.co.jp/en/
1-1-3 Higashiyamata, Tsuzuki-ku, Yokohama,
224-0023, Japan
Phone: [phone]
Facsimile: [phone]
©2015