kim lighting Micro-Flood KLV215 User manual

Part No. 95512Revision 10/14/11 EC 111014007 Status 22
INSTRUCTIONS PERTAINING TO A RISK OF INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS: Do Not overdrive fixtures with greater
than12 volts or fixture over-heating and short lamp life will occur. Do Not overload the transformer by
installing (or relamping) higher wattage lamps than planned. Note: Total wattage of all lamps connected to one
transformer must not exceed the capacity of that transformer. Do Not install luminaire within 10 feet (3.04m) of a
pool, spa, or fountain. DO NOT operate luminaire with missing or damaged lens.
SAFETY WARNING: When relamping be sure electrical supply is OFF. Low voltage fixtures can become
very HOT depending on the lamp wattage used. Glass lenses and metal areas above & around the lamp
can become HOT enough to blister hands. Use discretion when touching fixture and be sure to allow fixture to
cool before relamping. When relamping fixture avoid touching the lamp with bare hands. Lighted lamp is HOT!
If touching the lamp is necessary during installation, clean the envelope with alcohol and dry with a clean, soft
cloth before turning ON. Contamination of the envelope may reduce the lamp performance.
MAINTENANCE: To maintain light efficiency and prevent fixture-overheating, glass lenses and enclosure must
be kept clean and free from dirt, dust, leaves, trash (combustible materials) and mineral deposits from water.
Particular care should be taken not to locate fixtures where small children can reach them if higher wattage's are
used. Do not operate luminaire with missing or damaged lens.
Note: Keep the lamp free from impact while burning, as this may deform the filament and shorten the lamp life.
NOT INTENDED FOR INDOOR USE. All electrical work should be done by a qualified electrician.
P.O. Box 60080 •16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 •FAX [phone]
Micro-Flood®- KLV215/216/217Installation Instructions
KLV215
KLV216
KLV217
Tools Required: F" Hex Wrench Phillips Screwdriver B" Allen Wrench Adjustable Wrench
2. Attach fixture unto coupling.
Connect fixture cable to
main system cable with a
KLV410 Sealed Connector
(Part No. 95484).
Make certain electrical supply is OFF before starting fixture installation.
!
1. Attach coupling onto mounting
device. (See KLV Mounting
Options, part no. 95488.)
Note: Kim KLV Mounting
Options can be installed before
fixture is attached.
3. To install lamp, loosen the two (2) captive screws
on lens frame. Install lamp of type and wattage
shown on fixture label and chart on page 2.
Replace lens frame assembly making sure
gasket fits into the recess properly. Tighten
opposing screws progressively & evenly.
(Step 3 not required on L.E.D. version, for L.E.D.
fixture skip to step 4).
Captive Screws
!
Do not overload the transformer by installing (or
relamping) higher wattage lamps than planned.
Remember, the total wattage of all lamps
connected to one transformer must not
exceed the capacity of that transformer.
90°
*
*
*Note:
Swivel stem must be installed with the
mounting threads facing down-to
horizontal. Fixtures may not be installed
with mounting threads facing upward
unless shielded from rain or sprinklers.
!
Unit intended for mounting with Diffuser/Glass Barrier and Lamp Holder greater than 2 in. (5.08 cm)
from the ground plane.
KEEP THIS SHEET FOR FUTURE REFERENCE.

5. To adjust backtilt up to maximum,
loosen swivel screw being careful not
to disengage threads. Hold fixture at
desired angle and firmly tighten
swivel screw.
Lens Frame
Swivel
Screw
LAMP INFORMATION
Cat. No. Lamp Type Max. Watts
Halogen
KLV215 T3 or T4 Bipin 50
KLV216 MR16 Bipin 50
KLV217 L.E.D. 5
Micro-Flood®- KLV215/216/217 Installation Instructions
Page 2 KIM LIGHTING • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the following
exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the component
manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted
against defects of material and/or workmanship, and failure due to
corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be
warranted against defects of material and/or workmanship, and failure
due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil,
shall be warranted against defects of material and/or workmanship for a
period of 3 years from date of sale. Aluminum fixture components in
direct contact with soil shall be warranted from defects of material and
failure from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance
with applicable Kim instructions, specifications and accepted trade
practices, are covered by the Kim Warranty. During the warranty period,
with proof of purchase, Kim will repair or replace with the same or similar
product, at Kim's option, without charge. Labor costs are the owner's
responsibility and are excluded from this warranty. This warranty is void
if the product is modified, tampered with, misapplied, poorly installed,
improperly maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a
particular application. Kim Lighting shall not be liable to the purchaser
for indirect or consequential damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your input matters to us.
Additional wire and connectors may be
purchased from Kim Lighting:
KLV427 #12-2 Cable
KLV432 #8-2 Cable
KLV410 Connector
KLV411 Connector
Setscrew
4. Loosen setscrew, adjust fixture rota-
tion and tighten setscrew.
To Relamp turn off/unplug and allow
to cool before replacing lamp. Re-
place lamp per chart below. Lamp
gets HOT quickly! Contact only
switch or plug when turning on.