Kinesis Advantage360 KB360-Pro User manual

Quick Start Guide
This Quick Start Guide is designed to get you up and running with
keyboard basics. For additional details and full programming
instructions please read the User’s Manual and consult the other
support resources before embarking on this journey.
All Support Resources: kinesis.com/support/kb360pro
Visit the Official Kinesis YouTube channel for short tutorial videos
KB360-Pro

Kinesis ® Advantage360 Professional™ Keyboard
with the ZMK Programming Engine
ZMK firmware licensed under the Apache License version 2.0.
Contains FCC ID: 2ALGY-NRF52840
Keyboard models covered by this guide include all KB360-PRO
series keyboards (KB360-PRO-xxx).
© 2022 by Kinesis Corporation. All rights reserved.
KINESIS is a registered trademark of Kinesis Corporation.
ADVANTAGE360 and CONTOURED KEYBOARD are trademarks of
Kinesis Corporation.
WINDOWS, MAC, MACOS, LINUX, ZMK, BLUETOOTH and
ANDROID are property of their respective owners.
Proudly designed and hand-assembled in the USA since 1992.
Shop for Accessories: kinesis.com/products
Warning
The Advantage360 is not a medical treatment. Please consult
your doctor if you experience pain while using a keyboard and
discontinue use immediately.
Kinesis.com
Version 7.25.22 2

<Off / On> <On / Off>
In the Box
- Keyboard (KB360-PRO-XXX)
- 2 Charging Cables (USB-C to USB-A)
- Bridge Connector
- Extra Keycaps & Keycap Removal Tool
System Requirements
Computer with full-size USB-A port or Bluetooth®, and Windows
7-12®, macOS®, Linux®, or Chrome® operating system
Note: If your computer does not have integrated Bluetooth, you
may use a 3rd party Bluetooth dongle which is sold separately.
Battery
Each keyboard module is equipped with a rechargeable Lithium-Ion
battery. Turn on battery power by sliding the switch on the back of
each module away from the USB port. Batteries will automatically
charge whenever the module is connected via a charging cable.
Getting Started - Wired USB
Use one of the included cables to connect the left module to your
computer. Then power the right module by: 1) using the other cable
to connect it to the computer, or 2) turning on battery power via the
slide switch. Note: Anytime the left module is connect to a
computer keystrokes will be sent to that device over USB.
Getting Started - Wireless Bluetooth
Toggle both modules to battery power. Navigate to your computer’s
Bluetooth menu and locate the “Adv360 Pro” device and select
“Connect”. If the connection is successful, the Profile LED will go
solid white to indicate Profile 1 has been paired. Note: Exact
Bluetooth pairing will vary based on device and O/S, so consult your
computer’s operating manual or that of your Bluetooth dongle.
Linking Between Modules
The left and right modules always communicate wirelessly. 3

LOW MEDIUM HIGH
Ergonomics
The Kinesis contoured keyboard has stood the test of time since its
first introduction in 1992. The Advantage360 takes those same core
design principles and adds adjustable separation, rotation, and
tenting to suit any body type.
Learn More: kinesis.com/solutions/keyboard-risk-factors
Separation and Rotation
The most ergonomic typing position is one in which your hands are
in line with your arms for “straight” wrists. This can be achieved by
separating the modules to shoulder-width, by rotating the modules
“outward”, or any combination of the two. New users should start
with the modules closer together, and experiment with separation
and rotation to see what orientation feels most natural.
Optional Bridge Connector
For those who want to recreate the classic separation of our original
contoured keyboard, or those who just aren’t ready to make the
move to a fully split keyboard, simply snap the Bridge Connector
onto the keyboard base.
Warning: The Bridge Connector is NOT designed
to support the weight of the keyboard!!!
Adjustable Tenting
The Advantage360 features three adjustable “tenting” heights to
reduce forearm pronation. Depress the button on the underside of
each module and raise/lower the module to the desired height. The
lowest setting corresponds to the original contoured keyboard
height, but users can go up from there to find the perfect position.
4

Profile LED Color
1: White
2: Blue
3: Red
4: Green
5: Off
Layer LED Color
Base: Off
kp: White
fn: Blue
Mod: Green
*Note: Power users can enable
additional layers as needed.
Customizing Keycaps
Extra keycaps like macOS modifiers and “blanks” are included to
support keyboard customization. Use the keycap removal tool to
grasp the sides of a keycap and gently pull straight up to remove.
Carefully align the new keycap over the stem of the key switch and
press down gently. Note: Each keycap has a different height and
slope so it may not be suitable for every location on the keyboard.
6 Indicator LEDs
The Advantage360 Pro features 6 Indicator LEDs that display
important keyboard settings. The function and color of each LED are
shown below. Note: Not all indicator functionality is supported on
all operating systems over Bluetooth.
Caps Lock | Profile | Layer Num Lock | Scroll Lock | Layer
Troubleshooting - Flashing Red LEDs
If all 3 LEDs on the right module are FLASHING RED, it means the
right module cannot find the left module. Power-cycle both modules
using the slide switches to re-establish the connection.
Optional Palm Pads
If you purchased the all-new Palm Pads
separately, simply identify the correct side
and drop them into place. The magnets
will automatically center them on the
keyboard. Clean by wiping with a small
amount of lightly soapy water as needed.
5

Default Keyboard Layout
The Advantage360 may look intimidating at first, but the layout is
designed to work with your body and most keys are accessed with
the same fingers touch-typists are accustomed to using.
- Concave keywells place alphanumeric keys within easy reach
- Heavily-used editing keys are positioned under your thumbs
- F1 - F12 are accessed by holding either of the two “fn” layer keys
- The numeric keypad is accessed by tapping the “kp” layer key
- 4 blank “hotkeys” are available for macros or custom key actions
- Programming commands are triggered by key combinations
initiated with the “Mod” Key
3 Default Layers
Each key can perform multiple actions depending on which “layer”
is active on the keyboard. The layer LEDs will illuminate when you
move away from the base layer. By default, most keys perform the
same action in all three layers. If a key performs multiple actions, the
keycap will feature a second and/or third legend on its front face.
1) Base Layer: In the base layer, each key performs its primary
action, which is legended on the top of the keycap.
2) kp Layer: Tap the “kp” key on the left module to access the kp
layer, and tap it again to return to the base layer. Kp layer actions
are legended on the lower right corner of the keycap.
3) fn Layer: Press and hold either “fn” key with your pinky to access
the fn layer, and release to return to the base layer. Fn layer actions
are legended on the lower left corner of the keycap.
5 Available Profiles
The Advantage360 Pro has 5 Profiles so can you pair the keyboard
with up to 5 Bluetooth devices and quickly switch between them.
Switch Profiles: Mod + 1 - 5
Profile LED Indicates Pairing Status
- Fast Flash: Keyboard is ready to pair to a new device in this Profile
- Slow Flash: Previously-paired device for this Profile is not in range
- Solid: Keyboard is successfully paired
Clear Profile Pairing: Mod + Windows 6

SAFETAY MARGIN
Customize Backlighting
The Advantage360 Pro features backlighting and shine-through
keycaps so you can work in low-light environments. There are 5
brightness levels to choose from and the backlighting can be
adjusted on-the-fly. Use the shortcuts below to adjust backlighting.
Note: Battery life will be extended significantly if the backlighting is
dimmed or disabled.
Adjust Brightness: Mod + Arrow Up / Arrow Down
Disable Backlighting: Mod + Enter
Custom Programming
The open-source ZMK Programming Engine is an incredibly
powerful platform designed by keyboard enthusiasts, for keyboard
enthusiasts. Power users can edit the online configuration files to
customize the base layout, create additional layers, assign special
key actions, and write basic text-string macros. Note: The ZMK
Engine is hosted on the 3rd party GitHub platform. Kinesis does not
control this content and can only provide limited support.
Supported Key Actions: zmk.dev/docs/codes/
If you are not familiar with ZMK it is essential that you read the User
Manual before attempting to customize your keyboard. Custom
programming exceeds the scope of this guide and what follows is a
brief summary intended for experienced users.
1) Create (or Log-in) a GitHub account
Signup: https://github.com/signup
2) Fork the “Adv360 Pro ZMK” GitHub Repository:
Repo: github.com/KinesisCorporation/Adv360-Pro-ZMK
3) Enable Workflows from the “Actions” tab
4) Edit adv360.keymap or macros.dtsi (”Code” tab, “config” folder)
5) Click “Commit Changes”to initiate a new firmware build
6) Download the firwmare from Actions once the “build” has run 7

Graphical Programming
To access a graphical interface for reprogramming the keyboard,
visit the link below, authorize the App in GitHub, and then load your
personal Repository. From here you can create new layers, assign
new types of key behaviors (Note: ”&kp” is the default keypress)
and key codes, as well as create, edit, and assign basic macros.
When you have finished editing, click “Commit Changes” and follow
the instructions in this guide to download and install the firmware.
GUI: https://kinesiscorporation.github.io/Adv360-Pro-GUI/
Accessing the Bootloader and Installing Firmware Files
Each key module contains it’s own onboard flash storage which can
be accessed to install firmware files. With the respective key module
connected to a computer over USB, use the shortcuts below to
mount the removable drive named “Adv360 Pro”. Note: The
bootloader can also be accessed via a physical push button switch
using a paperclip (Consult the User’s Manual for details).
Left Module Bootloader: Mod + Hotkey 1
Right Module Bootloader: Mod + Hotkey 3
Install the downloaded firmware files by copying “left.uf2” to the
left drive first, and then by copying “right.uf2” to the right drive.
Note: Do not disconnect the cable until the update is complete. 8