Kingkong-AC ET series User manual

FPV EGG PNP
Instruction manual
LED StripBuzzer
HD CCD Camera
Micro Swift 2 High Quality Motor
Feature
* OV231 Camera, used OV solution and high definition.
* The structure uses 2.5mm thick carbon fiber and Super prop protector cover,
especially suitable for novice flying.
* Product performance and wheelbase for indoor through the special design.
* 4in1 10A 2S~3S AIO ESC support MULTISHOT,ONESHOT and DSHOT provedes
a better user experience.
* Modular design, PIKO BLX FC, with the latest betaflight firmware.
ET Series PNP
Instruction manual

ET100 Configuration
ET100 Package list
PNP*1 1935 Prop*4Pairs
Suitcase*1 Battery*1
USB×１
-1-
Unloading paddle×１ Rubber×２
ET100（Buzzer）
Wheelbase:100mm
Flytower20*20:
PIKO BLX(F303CC+MPU6000)
4in1 10A BLheliS
VTX:Q100 VTX(25mW/100mW 16CH)
Camera:OV231(800TVL 150 NTSC)
Motor:XT1103-7800KV
Prop:1935
Battery:7.4V 450mAh 80C
Weight:71.9g(without receiver and battery)
Receiver:FM800(Futaba),XM(Frsky),
FS-RX2A(Flysky),DSM2(Spektrum),RX800

ET115 Configuration
ET115 Package list
-2-
PNP*1 2345 Prop*4Pairs
Suitcase*1 Battery*1
USB×１ Unloading paddle×１ Rubber×２
ET115（Buzzer）
Wheelbase:115mm
Flytower20*20:
PIKO BLX(F303CC+MPU6000)
4in1 10A BLheliS
VTX:Q100 VTX(25mW/100mW 16CH)
Camera:OV231(800TVL 150 NTSC)
Motor:XT1104-7500KV
Prop:2345
Battery:7.4V 550mAh 80C
Weight:89.1g(without receiver and battery)
Receiver:FM800(Futaba),XM(Frsky),
FS-RX2A(Flysky),DSM2(Spektrum),RX800

ET125 Configuration
ET125 Package list
-3-
PNP*1 2840 Prop*4Pairs
Suitcase*1 Battery*1
USB×１ Unloading paddle×１ Rubber×２
ET125（Buzzer）
Wheelbase:125mm
Flytower20*20:
PIKO BLX(F303CC+MPU6000)
4in1 10A BLheliS
VTX:Q100 VTX(25mW/100mW 16CH)
Camera:OV231(800TVL 150 NTSC)
Motor:XT1104-7500KV
Prop:2840
Battery:7.4V 550mAh 80C
Weight:93.2g(without receiver and battery)
Receiver:FM800(Futaba),XM(Frsky),
FS-RX2A(Flysky),DSM2(Spektrum),RX800

Camera
Setting before
Install OV231 Connent OV231
Open canopy Connect USB
Pay attention to camera direction
-4-
Installation drawing
Canopy
Prop protector
（1.9/2.3/2.8inch）
FC
ESC
Stent plastic
Rubber band
M2.5
M2*7
Carbon fiber plate
100/115/125
Motor
1935 Prop(M2*6)
2345 Prop(M2*6)
2840 Prop(M2*8)
Camera
ST2*6
M2.5*18
VTX

FC
ESC
VTX
4.0V VIN GND VIDEO
25mW
100mW
-+
-
+VIN 2S-4S Lipo
7V-18V
GND
LED Frequency table
2-3S Lipo GND M1 M2 M3 M4
M1 M2
M3 M4
Motor
TX1
USART1
RX1
5V
GND
+
+
-
-
Satellite
S.BUS
PPM
2-3S Lipo GND M1 M2 M3 M4
GND 5V RX2 TX2 LED
GND
5V
PPM
GND
5V
RX3
GND
5V
RX3
PPM
3.3V
RX3
GND
BOOT
M4(CW) M2(CCW)
M3(CCW) M1(CW)
Click the key change frequency point
Please attention ventilation cooling
Antenna Q100-Mini 25mW/100mW 16CH VTX (2S-4S Lipo 7V-18V)
L=28mm,W=11mm,Weight=2.5g(Without camera and wire)
Buzzer
Race trasnsponder
Note:pay attention to the direction of rotation of the motor
when installing the prop
-5-

Receiver Bind
XM bind (default S.BUS),example(FRSKY X9D)
1. Open remote control, set D16 mode.
2. Hold receiver bind button to power, loosen until red and green light constant lighting.
3. Open remote control Bind, press “Enter” and wait a few seconds, then stop Bind when red light flash and green light
constant lighting.
4. Disconnect receiver power and power-on again, green light constant lighting means bind success.
.
.
-6-

-7-

Connect
PIKOBLX
3.1.6-PIKOBLX -27-02-2017 20:08(stable)
BETAFLIGHT firmware allready flash before leave the factory,user just need
connect PC to adjust the parameter.
1.Open betaflight configurator ,then click ,select FW version
2.Click , then click to download FW to FC,
click after FW updating finish into settings menu.
Firmware update
3.LED setting,select ，then open LED_STRIP
4.Buzzer setting,select ，then open VBAT
-8-
Product and Factory Code
Name
ET100 PNP NO RX
ET100 PNP XM
ET100 PNP FM800
ET100 PNP FS-RX2A
ET100 PNP DSM2
ET100 PNP RX800
ET100 KIT
ET115 PNP NO RX
ET115 PNP XM
ET115 PNP FM800
ET115 PNP FS-RX2A
ET115 PNP DSM2
ET115 PNP RX800
ET115 KIT
ET125 PNP NO RX
ET125 PNP XM
ET125 PNP FM800
ET125 PNP FS-RX2A
ET125 PNP DSM2
ET125 PNP RX800
Factory Code
PNP.ET100.NO RX
PNP.ET100.XM
PNP.ET100.FM800
PNP.ET100.FS-RX2A
PNP.ET100.DSM2
PNP.ET100.RX800
KIT.ET100
PNP.ET115.NO RX
PNP.ET115.XM
PNP.ET115.FM800
PNP.ET115.FS-RX2A
PNP.ET115.DSM2
PNP.ET115.RX800
KIT.ET115
PNP.ET125.NO RX
PNP.ET125.XM
PNP.ET125.FM800
PNP.ET125.FS-RX2A
PNP.ET125.DSM2
PNP.ET125.RX800
Factory Code
KIT.ET125
PROP.1935.3.WHITE
PROP.2345.3.WHITE
PROP.2840.3.WHITE
BAT.7.4V 450MAH 80C
BAT.7.4V 550MAH 80C
PART.BOTTOM PLATE.ET100
PART.BOTTOM PLATE.ET115
PART.BOTTOM PLATE.ET125
MOTOR.XT1103-7800KV
MOTOR.XT1104-7500KV
FC+ESC.FLYTOWER20*20
ESC.FLYTOWER20*20
FC.FLYTOWER20*20
PART.ET CANOPY
CAM.OV231
VTX.Q100
PART.1.9 PROTERTOR ALL.BLACK
PART.2.3 PROTERTOR ALL.BLACK
PART.2.8 PROTERTOR ALL.BLACK
Name
ET125 KIT
1935 Prop
2345 Prop
2840 Prop
Battery 7.4V 450mAh 80C
Battery 7.4V 550mAh 80C
Carbon fiber plate（ET100 Part）
Carbon fiber plate（ET115 Part）
Carbon fiber plate（ET125 Part）
XT1103-7800KV
XT1104-7500KV
Flytower 20*20
Flytower 20*20 ESC
Flytower 20*20 FC
ET Canopy
OV231
Q100 VTX
2.8 inch black propeller protector
(all surround)
2.3 inch black propeller protector
(all surround)
1.9 inch black propeller protector
(all surround)

6.PID Default setting
5.Default setting of receiver is 5th channel ARM,6th channel mode switching.
After sale service
1.Provide free reparation service when find the product defect after purchase.
2.Provide pay-needed reparation service when product damage because improper operation.
3.China customers please contact with the after-sales service,overseas client please contact the dealer.
PNP/RTF Test report ID :
Flight test
Transmitter functions properly
Flying in good condition
Camera OK
VTX OK
QC:
Package check
PNP
RTF
Frame
Transmitter
ID is the same
All parts of the installation
Insulating sleeves have been installed manual
Complete accessories,total packages
QC:
-9-
44
58
36
44
58
36