Kingkraft Contour User manual

Instructions for use
Contour Bath
PLEASE READ THESE INSTRUCTIONS BEFORE USE

CONTENTS
GENERAL DESCRIPTION
IMPORTANT SAFETY INSTRUCTIONS
OPERATING INSTRUCTIONS
ACCESSORIES
INSTALLATION
MAINTENANCE
CLEANING
STICKERS AND MARKINGS
GUARANTEE

General Description
Cushions and supports Flush spout Integral shower
(Backrest, base and side cushion option
supplied as standard)
Handset control
Pop up waste
Fold down door Thermostatic taps
         (maydiertopicture)

The Contour bath is a height adjustable bath that is to be used in establishments such as Care
Homes, Hospitals and private homes.
The bath is designed primarily as an assisted bathing bath incorporating a fold-down side for
easy access and variable height function to assist carers and transfer from wheelchairs.
The fold side also allows the Contour to be used as a general changing table and showering
platform.
Important Safety Information
•Do not stand on or in the product at any time
•Provisions must be made to be able to remove the user from the bath safely in case of emer
gency or power failure. This must be feasable when the bath is in any of its raised positions. (i.e
a mobile hoist incase the ceiling track hoist fails.)
•Kingkraft products are intended for domestic and commercial use only
•Donotexceeedthemaximumweightloadspecied(133kg/21st)
•Only one person should be in the bath at one time
•Only Kingkraft manufactured accessories have been tested by Kingkraft for safe use with this
bath under normal conditions of use
•Thebathisttedwithahandset,thisshouldnotbesubmergedinthewater,ifthishappensto
fall in, quickly wipe it dry and seek further advice if unsure
•YourContourBathshouldhavebeenttedatasafedistancefromthewalltoavoidtrapping,
howeveralwaysunsurethatalllimbs,head,ngersandtoesarenotontheoutsideofthebath
when it’s in motion
•Always check the temperature of the water before placing a person in the bath, this should be
ideally done with a calibrated thermometer
•Be aware when using bubble baths or foaming products, these can excessively froth, never
leave anyone unattended as there is a risk of drowning
•Never place anything or anyone underneath the bath - doing so could cause damage to per-
sons or the electronic mechanisms on the bath
• Thedropdownsideisloadbearingandwilltakethespeciedweightload,howeverthereis
always a risk of tipping, if you are unsure about the safety of the bath, contact Kingkraft
We would recommend sticking these safety instructions on the wall located near the bath
so that carers/other users are able to see them clearly. If you would like a laminated copy,
please let us know.
RISK OF SCALDING
Althoughsafetydevicesarettedtominimiseanyriskofscalding,usersmustbeawarethat
thesearenotfailsafe.Thetemperatureoftheunitmustbeindependentlyveriedoneach
occasion it is used-this should be tested, ideally with a calibrated thermomemeter.
Refer to Kingkraft if the water is too hot or too cold and do not used until the problem has been
corrected.
No person who is incapable of helping themselves must
be left unattended in the bath at any one time

Operating Instructions
TheContourBathisttedwithadropdownsidedoorwhichopensandclosesusingamanual
locking mechanism.
To open the door:
• Beforeopening,ensurethatnongers,toes,limbsoranyotherbodypartswillgettrappedin
the door
• Turn the lock handle to the right
• Then turn the open handle to the left
• The door should now open - make sure the door is fully pressed down before using
To close the door:
• Beforeclosing,ensurethatnongers,toes,limbsoranyotherbodypartswillgettrappedin
the door
• Pushthedoorupwardssoitisushwiththebathsides
• Turn the lock handle downwards only to lock the door, this should now be secure
Tap Instructions
YourContourBathwillhavebeenttedwithaRADASenseInfraredThermostaticMixerTap
(which will look like the below) , if you have any other type of tap, please refer to individual
manufacturing instructions.
The control panel can be mounted on the bath tub, a bracket or wall mounted near to the bath.
Moveyourhandinfrontofthe‘bathll’orthe‘shower’(ifapplicable)symbol/sensortostart
theowofwaterforthebathorshower.
Thetemperatureofthewatercanbeincreasedbyholding/wavingahandinfrontofthered
‘hot’ sensor on the right of the control panel. The temperature of the water can also be reduced
byholding/wavingahandinfrontoftheblue‘cold’sensorontheleftofthecontrolpanel.
Lights will indicate where between the minimum and maximum temperature the water tem-
peratureiscurrentlyset.Tostopthebath(orshower)lling,hold/waveahandinfrontofthe
‘bathll’(or‘shower’)symbol.TheabovebathlloptionsaresetbyKingkraftcommissioning
engineers(ifthishasbeenspecied)toamaximumtemperatureof44degreeswhenthebath/
showervalvecontrolisfullyturned/setatitsmaximum.Alwaysallowtimeforthemixedwa-
ter to run through the systems. With some boiler systems there can be soome temperature
uctuationwhenthetap/showerisrstturnedon,letthisstabalisebeforecontinuingtollthe
bath up or use the shower. Ensure the temperature is checked before placing someone in
the bath as there is a risk of scalding.
Operating the waste
The waste is operated by using the ‘handle’ situated on the side of the bath.
-Pull the ‘handle’ up to close the waste, press the plug down with your hand to make sure the
plugisproperlysealedbeforelling.
-To empty, simply push the ‘handle’ down and the plug will open up to allow the water to drain
away.

Operating the ‘up and down’ mechanism
Firstly ensure that no person(s) or objects can be damaged if the bath is raised or lowered
To raise the bath:
Press the ‘up’ button on the handset to raise the bath upward, release the button when it has
reached the desired position.
To lower the bath:
Press the ‘down’ button on the handset to lower the bath down, release the button when it has
reached the desired position.
Accessories
The additional accessories below are standard accessories available for the Kingkraft Contour,
you may have additional or dierent ones tted on your bath, always refer to the manufacturing
instructions for safe use.
Whirlpool, lights, music and cushions
To start the whirlpool:
Pressdowntheon/ocontrolbuttononthewhirlpoolbuttonlocatedontheedgeofthebath.
To increase the pressure of the whirlpool in the bath, turn the control button either clockwise to
increase or anticlockwise to decrease.
On/Oswitch
Adjusting the eye ball jets:
Thesecanbeadjustedbyplacingyourngerinthejetholeandturningittothedesiredposi-
tion.
Switch on/o:
Simplypressthemiddlebuttonforon/o
Whirlpool pump protection:
Shouldthewhirlpoolsystembeaccidentlyoperatedatanytimewithinsucientwater,thedry
runprotectionunitwillautomaticallyswitchthepumpo.Thewhirlpoolsystemcanonlyonly
thenbestartedwhenthereissucientwaterinthebath.Thewhirlpoolwillautomaticallyshut
oafter20minutes.(Youmayrestartitifrequired)Alwayshaveregardtotheusersmedical
conditions and state of health when using the whirlpool.
NOTE: Normal bubble baths will froth excessively with whirlpools and can pose a major
safety risk to the user and potentially cause damage to surrounding ttings. It is essential
that a low foaming bubble bath mixture is used and no one is left in the bath unattended at
any time.
Please refer to cleaning instructions on how to keep your whirlpool clean.

Lights
Yourbathmaybettedwithintegrallightstohelpcreateasensoryexperiencewhilstbathing.
There may be risk to some users, so always check with medical experts before use if you are
unsure.
        Turnlightson/o
Change sequence of lights
Music
YourbathmaybettedwiththeintegralBluetoothmusicsystem,ifsosimplyconnectviaany
device that has ‘in built’ Bluetooth i.e Smartphone, Tablet etc. Search for ‘Soundbathe’ and con-
nect and listen away whilst you bathe.
Cushion and Supports
Kingkraftoerarangeofsupportsandcushioningtomakebathtimemorerelaxing.Separate
instructions will be enclosed with your cushioning, however please see below information on
how to safely use your cushions.
OurcushionsaremadefromPCVandfoamllerorpolysterenebeads.Ensure that no person
is allergic to these materials before use.
Thereisariskofoating,thereforepleaseensurethatthecushionsandsupportsaresecurely
fastened to the bath before use.
•Ensurethatthebathbottomandmattresses/suckersareclean
•Placecushions/supportssecurelyontobase/sideofbath
•Run a small amount of water into the bottom of the bath
•Pressthecushions/supportsrmlyontothebath
Do not use any oil based bathing products as this could aect the suckers sticking to the bath.
When removing the cushions/supports, take care that each sucker is prised carefully away from
the bottom/side of the bath to avoid a tearing action. If the cushion rips around the suckers this is
not covered under any manufacturing warranty and you will be charged to replace it. Make sure
your cushion and supports are cleaned regularly.

Installation
Your Contour should have been installed by a competent installer. The bath should have been
commissionedandacommissioncerticateproduced.Ifyouareunsureaboutthesafeinstal-
lation of your bath, please contact Kingkraft immediately.
If you have to move or re-install your bath for any reason, Kingkraft are able to carry out this
work, just get in touch with us for more information. In all cases, we recommend that we carry
outanyinstallation/commissioningwork.
Units with electrical services must only be wired in accordance with the IEE Wiring Regula-
tions, especially as regards zoning equipotential bonding. Kingkraft products are intended for
operation only in a bathroom type location where exposed mains connections and unsealed
switches etc are not permitted.
This unit must not be connected via a plug and socket
Maintenance
YourContourBathcomeswitha2yearmanufacturingwarranty,thisisforlabourandparts
only. Kingkraft recommend an annual service on the Contour
Kingkraftcancarryoutanannualservice,pleasegetintouchtondoutfurtherinformation.
Fault Finding: If your bath is not going up and down but making a ‘beeping noise’
•Firstlycheckthatthepowersupplyhasnotbeenturnedotothebath.
•To check whether there is power, if possible and is safe to do so, check underneath the bath
to see whether there is a green light on the control box. Alternatively, if you know where the
mainpowersourceisforthebath,checkthatisnotturnedo.
•If your bath is still not going up and down and have you done all the checks, contact Kingkraft
for further advice.

Cleaning
Do not use any cleaning agents that contain bleach or other corrosives as this can cause stai-
ing and can invalidate the warranty. Use only water, normal soaps and approved cleaning
agents. We recommend using Chemgene which can be purchased via Kingkraft.
Ifyourbathisttedwithanycushionsorsupports,theseshouldberemovedideallyaftereach
use to ensure that no soap scum has built up underneath. If these are left in the bath for a
length of time, mould can quickly build up which can cause damage to health.
Cleaning the whirlpool (if tted)
It is important the whirlpool is cleaned regularly, if you are in a Multi-user environment then this
should be done after each use. Please follow the below guidelines on how to clean your whirl-
pooleciently.
•Remove all cushions and supports in the bath (if applicable)
•Rinse any debris from the bath
•Close drain by operating the pop-up waste
•Fillthebathwithwatertoalevelof25mm(1”)abovethewhirlpooljets
•Put the whirlpool cleaner in (we recommend the Bronte Whirlpool 6 month care pack, but you
can pick up whirlpool cleaners from most hardware stores)
•Follow the instructions on the packet
•Runwhirlpoolfor15minutes(thismaydiertowhichevercleaneryou’reusing)
•Drain bath
•Fill bath with clean water to measurements
Stickers and Markings on your Bath
Your Contour should have the following two stickers, if it doesn’t-please make Kingkraft aware
ofthisassoonaspossible.Youwillndyourserialnumberonthissticker,ensureyoumakea
note of this and keep it safe for future reference.
WEEE(WasteElectricalandElectronicEquipmentRegulations2006)
The aim of this Directive is to minimise the impact of electrical and electronic equipment on
the environment when products become waste. All electrical components on this product
mustbedisposedofinaccordancewiththeWEEE2006regulations,eitherthroughreuse,re-
covery, recycling or environmentally sound disposal.
If this Kingkraft product is at the end of its life cycle and is being disposed of by people other
than Kingkraft engineers, please contact Kingkraft to discuss arrangements regarding the dis-
posal of any electical equipment.

Guarantee
Your Kingkraft Contour Bath is guaranteed for two years, this covers any breakdowns and parts
for this period only. Full terms and conditions can be found on our website as to what the war-
ranty covers.
Yourbathmayhavebeenpurchasedwithaveyearwarranty,ifyouareunsurepleasecheck
uponreceivingyourproductwhetheryouhaveanextendedwarrantyaswecannotoerthis
once your item has been installed.
Please ensure you make a note of your serial number(s) which can be found either on the
productitselforonanypaperworkleftbytheengineerwhentted.
Youshouldhavebeenleftawarrantycardwithyourbath,toensureweoeryouthehighest
customer service, please register your details to ensure we have up to date information. You
can do this by visiting www.kingkraft.co.uk/pages/register-your-product
We would also appreciate if you would also complete our short survey about your experience
with Kingkraft.
In the unfortunate event that you experience a breakdown and you think you are still covered
underwarranty,pleasecontactourmainoceon01142690697orinf[email protected].
But don’t worry, if the product is out of warranty and having problems we can still attend, how-
ever charges will apply for our engineers visit, please ensure you know who would be funding
this charge when you call us as we can not attend a product without prior authorisation from
the bill payer.
Moving house or disposing of the bath?
If we do not know already, we would appreciate it if you are moving house or disposing of your
bath that you advise us so that we can keep our records up to date.

CONTOUR-CBIFU-ISSUE3-10/19
Kingkraft Ltd26DOrgreaveCrescent,DoreHouseIndustrialEstate,Sheeld,S139NQ
phone 01142690697email[e-mail]web www.kingkraft.co.uk