KIP KIP C7800 User manual

DIGITAL COLOR PRINTER
KIP C7800
Hardware Operation Guide
Version A.0
- Please read this Hardware Operation Guide
before using the printer.
- Please keep this Hardware Operation Guide
for future reference.
KATSURAGAWA ELECTRIC CO., LTD.

(1)
Thank you for purchasing the DIGITAL COLOR PRINTER KIP C7800.
This Hardware Operation Guide contains functional and operational explanations for the KIP C7800.
Please read this Hardware Operation Guide carefully before using the Printer.
Please keep this Hardware Operation Guide for future reference.
When this machine is installed in U.S.A.
This equipment satisfies the requirements in Part 15 of FCC Rules for a Class A computing device.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
When this machine is installed in Europe
This equipment satisfies the requirements in Pub.22 of CISPR Rules for a Classic A computing
device.
Operation of this equipment in a residential area may cause unacceptable interference to radio and TV
reception requiring the operator to take whatever steps are necessary to correct the interference.
Do not install this machine around electronic equipment or precision instruments.
Other devices may be affected by electrical noise during operation.
If Machine is installed near other electronic equipment, such as a TV or a radio, interference
to said equipment, such as noise or flickering, may occur.
Use a separate power line and install the PRINTER as far as possible from said equipment.
The International ENERGY STAR ® Office Equipment Program is an international program that
promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.
The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to GB
18455-2001 11364-2006 of National Standard of the People’s
Republic of China and does not apply to countries outside of
People’s Republic of China.
KIP C7800 is an ENERGY STAR qualified printer.
The symbol shown indicates that this product conforms to Directive
2002/96/EC of the European Parliament and the council of 27 January
2003 on waste electrical and electronic equipment (WEEE) and does not
apply to countries outside of EU.

Chapter 1 Before Use
1-2
1. 1 Installation Requirements
The following conditions are required for installation of the equipment.
(1) Power source should be as follows (according to your region).
U.S.A. / Europe 220 to 240V (+6% to -10%), 20A or higher, and 50/60Hz
(2) The equipment must be on an exclusive circuit.
The outlet must be near the equipment and easy accessible.
(3) Make sure to connect this equipment to a grounded outlet.
(4) The site temperature range = 15 to 27 degrees centigrade, with the humidity between 20% to
70% RH (NON CONDENSING).
Keep the equipment away from water sources, boilers, humidifiers or refrigerators.
(5) The installation site must not have open flames, dust or ammonia gases.
(6) The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
(7) Ozone will be generated while this equipment is in use, although the quantity generated is
within safe levels. (see certifications)
Ventilate the room, if required.
(8) Levelling Bolts on the bottom of the KIP C7800 should touch the floor correctly.
And the equipment must be levelled.
Floor strength must be ample to sustain the weight of the equipment.
(9) Keep ample room around the equipment to ensure comfortable operation.
Required space is noted.
120cm (48”)
or wider
150cm (59”) or wider
65cm (26”)
or wider
Rear
Front
206cm (81”) or wider
(When optional Auto Stacker is
used.)
187cm (74”) or wider
(When accessory Tray is used)

Chapter 1 Before Use
1-5
1. 4 Specifications
Subject Specification
Model KIP C7800
Type Console
Printing method LED Array Electro Photography
Color CMYK
Photoconductor Organic Photoconductive Drum
Print speed Color : 100mm / second max. (4.6ppm / 36”x48”) (4.7ppm / A0)
(for Roll Deck 3), speed varies by media type)
Mono : 120mm / second (xx ppm / 36”x48”) (xx ppm / A0)
Exposure method Multi-Level (tone number 9) LED Print Head
Resolution 600dpi x 2400dpi
Print width Maximum : 914mm (36 inches)
Minimum : 297mm (11 inches)
Print length Maximum :
Minimum : 210mm (8.5 inches)
NOTE : If the print is longer than 6m, KIP does not guarantee
image quality or the reliability of media feeding system.
Plain Paper / Bond 5x Standard Roll Deck 3
2x Standard Roll Deck 1, 2
Tracing Paper / Vellum 1x Standard
Film 1x Standard
Glossy Paper 1x Standard
Warm up time Shorter than 4 minutes
(At 23 degrees centigrade, 60% RH and 220V)
First print time Shorter than 33 seconds (36 x 48 inches)
Fusing method Heat roller fusing
Development Contact type mono component non-magnetic development system
(Initial toner is unnecessary. One toner cartridge contains 1kg.)
Charging method Corona
Transfer method Transfer roller
Media feeding method Automatic (*3 Roll Decks) and manual (**20 cut sheets capacity)
* Image quality on A3, 15”, 12”, 11” width roll media is guaranteed with
using Roll Deck 3 only
** A2 - A4 (24” - 11”) in Portrait orientation only
Input power 220 to 240V (+6% to -10%), 20A and 50/60Hz
Interface Ethernet 10BASE-T, 100 BASE –TX, 1000 BASE-T
USB 2.0 (5VDC max)
Power consumption On 230V, 50/60Hz 3.6 kwh (Maximum)
Stand by 0.8 Kwh (Average)
Printing 2.2 Kwh (Average)
Warm up 3.4 Kwh (Average)
Acoustic noise Less than 65db (Printing)
NOTE : Impact noise such as cutting sound is excluded.
Less than 60db (Stand by)
Ozone Less than 0.05ppm (Average of 8 hours)
Dimensions 1376mm (Width) x 790mm (Depth) x 1450mm (Height)
Weight About 540kg

Chapter 1 Before Use
1-6
Subject Specification
Media Plain Paper / Bond:
Color mode: 70 to 150g/m2
* For heavier media (90 to 150g/m2), use media type setting “Heavy”.
Mono mode: 70 to 75g/m2
Environmental
condition Temperature 15 to 27 degrees centigrade Humidity 20 to 70% RH
Storage condition of
consumables Print media Wrap the media surely to shut out the humidity. Toner Keep the toner cartridge away from the direct
sunlight, and store it in the condition of 0 - 35 oC
and 10 - 85% RH.
NOTE
These specifications may be changed without notice.

Chapter 2 Basic Operations
2-2
2. 1 Turning on the KIP C7800
1. Plug the KIP C7800 to an exclusive wall outlet.
2. Press “|” side of the Power Switch on the front to turn on the KIP C7800.
3. The Status Indicator above the Power Switch flashes green while warming up.
NOTE
Please confirm the outlet satisfies the following condition before plugging the KIP C7800 into.
220-240V (+6% to -10%), 20A, and 50/60Hz
Status Indicator (Blink)
Press this side
NOTE
The machine does not operate at all If the
circuit breaker is turned off.
Flip up the circuit breaker switch to turn on the
power supply.

Chapter 2 Basic Operations
2-3
4. The KIP C7800 will get ready about 3 minutes after turning on.
The Status Indicator stops blinking and lights green when ready.
Make a copy or print from outer devices.

Chapter 2 Basic Operations
2-4
2. 2 Turning off the KIP C7800
1. Press “ ” side of the Power Switch on the front to turn off the KIP C7800.
2. The Status Indicator flashes light purple while the embedded controller unit is shutting down.
It will turn off in 2 minutes.
NOTE
The controller unit starts shutdown process after turning off the KIP C7800, and it will take
about 2 minutes until complete shut down. Do not unplug the KIP C7800 from the outlet for
about 2 minutes after turning off therefore. The controller unit may be broken if the KIP C7800
is unplugged before the completion of shut down process.
Status Indicator (blinking)
Press this side

Chapter 2 Basic Operations
2-5
3. If you completely shut the power supply due to a long vacation or the machine’s transport, turn
off the circuit breaker and then remove the power cable from the machine.

Chapter 2 Basic Operations
2-26
2. 8 Sleep Mode
The KIP C7800 has two Sleep Modes to reduce the power consumption.
The KIP C7800 will enter Sleep Mode after a certain period of inactivity.
In the default setting;
•Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power
supply for Fuser Unit.
•Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser
Unit and some other components.
You can set the period to 240 minutes for example. See further information on Touchscreen
Configuration.
Sleep Mode is canceled and the machine gets ready when;
•the machine receives a print job through the network.
•you tap on the UI screen.
NOTE
(1) It may take time for the machine to get ready.
(2) Recommended Default Delay Times for Cold Sleep: 60min
(3) Cold Sleep Mode meets the Printer Sleep Mode statement of ENERGY STAR® Office
Equipment Program.