KIP 7770 User manual

KIP7770UserManual
Version A.0

(1)
Thank you for purchasing the KIP 7770.
This USER'S MANUAL contains functional and operational explanations for the KIP 7770.
Please read this USER'S MANUAL carefully before using the Printer.
Please keep this USER'S MANUAL for future reference.
1. When this product is installed in North America.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of this device.
Contains FCC ID: VP8-13551 Contains IC: 7391A-13551
2. When this machine is installed in Europe
This equipment complies with the requirements in Pub.22 of CISPR Rules for a Class A
computing device.
Operation of this equipment in a residential area may cause unacceptable interference to radio
and TV reception requiring the operator to take whatever steps are necessary to correct the
interference.
Do not install Machine around other electronic equipment or other precision instruments.
Other devices may be affected by electrical noise during operation.
If the Machine is installed near other electronic equipment, such as a TV or a radio,
interference to said equipment, such as noise or flickering, may occur.
Use a separate power line and install the PRINTER as far as possible from said equipment.
The International ENERGY STAR ® Office Equipment Program is an international program that
promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.
KIP 7770 is an ENERGY STAR qualified multifunction device.

(2)
The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to GB
18455-2001 11364-2006 of National Standard of the People’s
Republic of China and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to Directive
2002/96/EC of the European Parliament and the council of 27 January
2003 on waste electrical and electronic equipment (WEEE) and does not
apply to countries outside of EU.

(3)
The following warnings are very important in order to safely use this product.
These notes are important in preventing danger to the operator or operation of the printer.
The following symbols are found throughout the USER’S Manual and have the following meaning:
WARNING
This WARNING mark means that there is a possibility of death or serious
injury if you ignore or do not follow the said instruction.
CAUTION
This CAUTION mark means that there is a possibility of injury or physical
damage if you ignore or do not follow the said instruction.
When marked with this symbol, “DO NOT ATTEMPT”
When marked with this symbol, “pay close attention to”
Safety Warning

(4)
WARNING
1. The Power source should be as follows:
220 to 240V plus 6% or minus 10%, 50/60Hz, 20A or higher
2. Use a circuit with a dedicated breaker.
3. Install the product as close to the wall outlet as possible.
4. If you wish to move the printer, please contact your service personnel.
Ground the product with a correct ground source or you may be electrically
shocked.
1. Do not plug in the printer into a multi-wire connector in which some other
equipment is plugged into.
It may cause a fire due to outlet overheating.
2. Do not damage the Power Cord by stepping on or placing heavy items
on it.
If the Power Cord is damaged, it may cause a fire or you may receive
an electric shock. REPLACE THE CORD IF DAMAGED!
1. Do not put a flower vase, a flowerpot or any water-filled item on the
product.
Spilt water could cause a fire or an electric shock.
2. If the product generates an abnormal smell or noise, turn it off and
unplug it from the wall electrical outlet immediately.
1. Do not remove the screw and do not open the cover if not instructed to
do so in this User’s Manual. If you ignore this warning, you may be burnt
or receive an electric shock due to a hot item or electrically charged part
inside of the printer.
2. Do not disassemble or tamper with the printer.
It may result in a fire or an electrical shock.
Do not throw the toner into a fire or other sources of heat, as it can
explode.

(5)
CAUTION
There are hot items inside of the printer.
Take great care not to touch these items when you remove mis-fed media.
Do not pull the cord when you unplug the printer as you may damage the
Power Cord.
Do not install the printer in a humidified room or a dusty room.
Also, do not install the printer on an unstable floor as injuries may occur.
1. Unplug the printer before you move it.
The power cord may be damaged and it may result in a fire or electric
shock.
2. If you do not use the printer for a long duration (holidays, company
shutdown) turn off and unplug the printer from the outlet for safety.
Ventilate the room well if you print in a small area.

(6)
POWER CORD INSTRUCTION
The installation of (or exchange to) a power plug which fits in the wall outlet of the installation
location shall be conducted in accordance with the following:
WARNING
Select a power plug which meets the following criteria;
- The plug has a voltage and current rating appropriate for the product’s rating marked on
its name plate.
- The plug meets regulatory requirements for the area.
- The plug is provided with a grounding pin or terminal.
If the appropriate plug does not fit the wall outlet in the installation, the customer shall install an
appropriate outlet.
Connector Type:
Configuration Standard Rating Usually found in
IEC60320:C19 20A 250V (UL)
16A 250V (IEC)
Plug Type: Model Rating 220-240V
Configuration Standard Rating Usually found in
NEMA6-20 20A 250V North America
(UL Listed)
CEE7/7 16A 250V European countries
KS C 8305 16A 250V Korea
AS/NZS 3112 16A 250V Australia
New Zealand
GB1002
GB2099.1
16A 250V China
IRAM 2073 16A 250V Argentina
Cord Type
Standard Rating Usually found in
SJT 3X12AWG Long <4.5m 20A 250V North America
(UL Listed)
HO5VV-F 3X1.5mm2 16A 250V European countries
Argentina
RVV 3X1.5mm2 16A 250V China

Chapter 1 Before Use 1-1
Chapter 1
Before Use
Page
1. 1 Installation Requirements 1- 2
1. 2 Originals Prohibited from Duplication 1- 3
1. 3 Features 1- 4
1. 4 Specifications 1- 5
1. 5 Appearance 1- 7
1. 5. 1 Front 1- 7
1. 5. 2 Rear 1- 8
1. 6 Optional Configurations 1- 9
1. 7 Specifications for Printing Media 1-10
1. 7. 1 Available Print Size 1-10
1. 7. 2 Media not to be used 1-11
1. 7. 3 Maintaining Media 1-12
1. 7. 4 Environmental Condition - Correction 1-13

Chapter 1 Before Use 1-2
1. 1 Installation Requirements
The following conditions are required for installation of the equipment.
1. Power source should be rated as follows.
220V - 240V plus 6% or minus 10%, 50/60Hz, 20A or higher
2. The equipment must be on an exclusive circuit.
3. The outlet must be near the equipment and easily accessible.
1. Make sure to connect this equipment to a grounded outlet.
2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near
the equipment and shall be easily accessible.
1. The installation site must not have open flames, dust or ammonia gases.
2. The equipment must not be exposed to the air vents from air conditioners.
It may affect the image quality.
3. The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
When you open the Upper Unit to remove a mis-feed, do not expose the
Photoconductive Drum to strong (intense) light as this will damage the Drum.
Ozone will be generated while this equipment is use, although the quantity generated is
within safe levels. (See certifications.)
Ventilate the room, if required.
The site temperature range = 10 to 32 degrees Centigrade, with the humidity between
15% to 85% RH. (NON-CONDENSING)
Keep the printer away from water sources, boilers, humidifiers or refrigerators.
Keep ample room around the equipment to ensure comfortable operation.
(Refer to the following figure.)
The equipment must be leveled and the floor strength must be ample to sustain the
weight of the equipment.
Left: 50mm / 2” Right: 300mm / 12”
or larger or larger
Rear
Front
Printer
800mm / 32” or larger
800mm / 32” or larger

Chapter 1 Before Use 1-3
1. 2 Originals Prohibited from Duplication
It is not necessarily allowed to copy every kind of original.
You may be punished by the law if only you possess the copy of some kind of original.
We recommend you to consider enough before you copy such original.
[Originals prohibited from copying by the law]
1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.), Government issued
Negotiable Instruments (National Bonds, Security, Local Debt Bonds, etc.).
2. It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments.
3. It is not allowed to copy unused postal stamps or government postcards without permission
to make replica from Government.
4. It is not allowed to copy Government issued revenue stamps, certificate stamps which are
prescribed by Liquor Tax Act or the Commodity Tax Act.
[Special items to be cared]
1. It is warned by the government to copy private issued securities (stock certificate, draft,
check, goods ticket, etc.), commutation ticket or book of tickets, excluding that some specific
company copies such originals as many as it requires for its own business.
2. We recommend you not to copy freely such originals as government issued passport, public
or private issued licenses, automobile inspection certification, IDs and tickets like pass or
meal.
Reference Law Prohibited items to copy
Regulations to control fake currency and
Bond.
Currency (Bill, Money, Bank Note, etc.),
Government issued Negotiable Instruments
(National Bonds, Security, Local Debt Bonds,
etc.)
Control Law against Forged & faked
Foreign Currency, Bill, Bank Note and Bond
Foreign Currency or Foreign Negotiable
Instruments
Forged postal stamps control law Unused postal stamps or government postcards
Forged revenue stamps control law Government issued revenue stamps, and
certificate stamps prescribed by Liquor Tax Act
or Commodity Tax Act
Currency similarity securities Control Law Private issued securities (stock, draft, check,
goods ticket, etc.), commutation or book tickets
[Originals protected by the copyright]
It is prohibited to copy such originals as book, music, paintings, printed copy, maps, drawings,
movie and pictures which are protected by the copyright, except for personnel or family use or
similar purpose.

Chapter 1 Before Use 1-4
1. 3 Features
• KIP 7770 Digital Printer can make a print in a speed of 120mm per second.
The maximum print size is 36 inches (914mm) wide, and the minimum one is 8.5 inches
(210mm) for cut sheet media, and 11 inches (294mm) for roll media.
• The print image is more stabilized than before since we adopt a minute toner for mono-
component development.
• Density Compensation Process provides consistent image density in various environments.
• The combination of KIP Contact Development System and mono-component minute toner can
produce a high definition line, distinctive grayscale and consistent solid black.
The KIP HDP process generates no Waste Toner.
• Flange type loading mechanism eases operator’s media loading work.
• Easy access to USB port allows users to provide efficient productivity by using “File to Print” /
“Scan to USB” (option).
• Some optional stacking items are available, such as “High Capacity Print Tray” that can stack
about 100 prints (plain paper/bond) ejected to the rear side, and “Paper Exit Kit” that can sort
the prints to front ejection and rear ejection and then stack them on front tray and rear tray.
• The KIP 7770 adopts 12.1 inch screen for the UI, wider than 10.4 for our old products.
The capacitive multi-touch screen offers smooth, various and intuitive user operation that a
pressure sensing device lacks.
• The Energy Star ® guideline 2009 compliant

Chapter 1 Before Use 1-5
1. 4 Specifications
Subject Specification
Model KIP 7770
Configuration Console
Printing method Electro photography
Photoconductor Organic Photoconductive Drum
Print speed 120mm per second
(Inch) E: 5 sheets/min D Landscape: 9 sheets/min
(Metric) A0: 5 sheets/min A1 Landscape: 9 sheets/min
Print head LED
Resolution 600dpi x 2400dpi
Print width Maximum 36” (914mm)
Minimum Roll: 11” / 297mm
Cut sheet (Portrait): 8.5” / 210mm
Print length Maximum
(Standard) 6,000mm (bond, 36” / A0 wide only)
or “5 x Standard length” (bond)
“2 x Standard length” (vellum)
“1 x Standard length” (film)
(Option) 24,000mm
Minimum 8.5” (210mm)
NOTE: If the print is longer than the maximum listed above, its
image quality or the reliability of paper feeding is not
guaranteed.
Warm up time Less than 2 minutes
(23 degrees Centigrade, 60% RH and the rated voltage / Bond)
First print time 21 seconds (A0 from Roll 1)
Fusing method Roll Fuser
Development method Dry type with non-magnetic mono-component toner
Exposure method LED
Charging method Corona
Transfer method Corona
Separation method Corona
Input power 220V - 240V plus 6% or minus 10%, 50/60Hz, 20A
Power consumption Maximum 3120W or less
Stand by 1100W (Average)
Printing 2100W (Average)
Cold Sleep 2.5W
230V, 50/60Hz and Dehumidify Heater is ON
Acoustic noise less than 65db (Printing)
less than 55db (Standby)
Ozone less than 0.05ppm (Average)
Dimensions 1370mm (Width) x 725mm (Depth) x 950mm (Height) (w/o UI)
1702mm (Width) x 725mm (Depth) x 1377mm (Height, max) (w/ UI)
Weight Approx. 333kg (2 Roll type)
Approx. 375kg (4 Roll type)
Media (Recommended Media)
US model:
Plain Paper 64g/m2 to 80g/m2, US Bond (PB-20)
Tracing Paper US Vellum (XV-20)
Film 4MIL (PF-4DME)
Europe/Asia model:
Plain Paper 64g/m2 to 80g/m2, Diamond Plain Paper (80g/m2)
Tracing Paper Gateway Tracing Paper (73g/m2 )
Film NSF4MIL Film
(continued on the next page)

Chapter 1 Before Use 1-6
Subject Specification
Environmental condition
for usage
Temperature: 10 to 32 degrees Centigrade
Humidity: 15 to 85% RH
Interface Ethernet (10 BASE-T, 100 BASE-TX, 1000 Base-T)
Serial port (RS232-C)
USB 2.0
Storage of consumables (Media)
Wrap the media surely to shut out the humidity.
(Toner cartridge)
Keep the toner cartridge away from the direct sunlight, and store
it in the condition of 0 to 35 degrees Centigrade and 10 to 85%
RH.
NOTE
The above specifications are subject to change without notice.

Chapter 1 Before Use 1-7
1. 5 Appearance
1. 5. 1 Front
Name of part Function
1 User Interface (UI) This is a Touch Screen, and many user operations are available.
PLEASE DO NOT push the LCD area too strong.
2 Top Cover Open here to clear the mis-feed paper.
3 Manual Table Open here to insert a cut sheet or to pull the Upper Frame Unit.
4 Roll Decks Each Roll Deck drawer holds 2 rolls of print media.
5 Power Switch You can turn on/off.
1
3
4
5
2

Chapter 1 Before Use 1-8
1. 5. 2 Rear
Name of part Function
1 Exit Cover Open the Exit Cover when you remove the mis-fed media.
2 Dehumidify Heater
Switch
Press “H” to turn on the Dehumidify Heater, and press “L” to turn it
off.
3 Inlet Socket Connect the power cord here.
4 Breaker It is possible to shut off supplying the AC power.
5 USB connector
(USB2.0)
Connect the cable to this terminal for a KIP Scanner (option).
(max.5Vdc)
6 COM Port Connect the cable from a finishing device (option).
(D-Sub Connector 9 pins: max.12Vdc (Small))
7 LAN Port Connect the LAN Cable to connect the KIP 7770 to the network.
(Do not connect a telephone line.)
1
2
3
4
5
6
7

Chapter 1 Before Use 1-9
1. 6 Optional Configurations
You can combine the KIP 7770 Printer with optional outer devices.
Please contact your dealer for further information of integrating KIP 7770 to your network and other
devices.
KIP 7770 + KIP Scanner
KIP 7770 on network
Other printers
KIP Scanner
USB2.0
Scanner
Controller
Workstation
KIP 7770
WEB
KIP 7770
KIP Scanner

Chapter 1 Before Use 1-10
1. 7 Specifications for Printing Media
1. 7. 1 Available Print Size
Available print size is as follows.
Minimum Maximum
Width 11”/ 297mm (Roll)
8.5”/ 210mm (Cut Sheet) 36” / 914mm
Length 8.5”/ 210mm 6m
NOTE
It is possible to print longer than 6 meters as an option.
Call your service personnel if you would like to print over 6 meters as the user can not
change this setting in the printer.
If you print longer than 6 meters, the image quality or the reliability of media feeding is
not guaranteed.

Chapter 1 Before Use 1-11
1. 7. 2 Media not to be used
Do not use the following kinds of printing paper. Doing so may damage the printer.
Excessively curled
Folded
Creased
Torn
Punched

Chapter 1 Before Use 1-12
Pre-printed
Extremely slippery
Extremely sticky
Extremely thin and soft
OHP Film
1. 7. 3 Maintaining Media
Keep the paper in the custody taking care of the following matters.
1. Do not expose the paper to the direct sunlight.
2. Keep the paper away from high humidity. (It must be less than 70%)
3. Put the paper on a flat place, do not damage the media.
4. If you will keep paper which you has already been unpacked, put it into the plastic bag to
avoid humidity in the media.
CAUTION
Do not use the paper with staple, or do not use such conductive paper as aluminum foil and
carbon paper.
The above may result in a danger of fire.
NOTE
(1) Print image may become light if printed on a rough surface of the paper.
(2) Print image may become defective if the print paper has an excess curl.
(3) It will cause paper mis-fed, poor print image or creasing if you use a paper that does not
satisfy the specifications.
(4) Do not use a paper of which surface is very special, such as thermal paper, art paper,
aluminum foil, carbon paper or conductive paper.
(5) Vellum exposed to air over a long period tends to cause a defective printing.
It is recommended to remove one round on the surface of the vellum roll from the
beginning.
(6) Remove fully any adhesive from the roll that may remain due to tape placed by the media
supplier.
(7) Do not use papers with unpacked (exposed in high / low temperature & humidity) in a
long period. Such papers may result in mis-feed, defective image or paper creasing.
(8) It is recommended to trim the leading edge by using Initial Cut Key on the User Interface
(UI) before making a long print.

Chapter 1 Before Use 1-13
1. 7. 4 Environmental Condition - Correction
Take a necessary treatment according to the environmental condition as shown below.
Humidity(%) Possible problem Necessary treatment
Low
40%
70%
High
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and vellum.
1. Install the humidifier in the room, and
humidify the room air.
2. Remove the media from the machine
right after the completion of print, and
keep it in a plastic bag.
“Void of image” occurs when you print
with vellum.
If you will not make print soon, remove
the vellum from the machine and keep it
in a plastic bag.
Remove the paper from the machine after
everyday use, and keep it in a plastic bag.
“Void of image” occurs when you print
with plain paper and vellum.
If you will not make print soon, remove
the media from the machine and keep it in
a plastic bag.
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and vellum.
1. Turn on the Dehumidify Heater.
2. Remove the media from the machine
right after the completion of print, and
keep it in a plastic bag.
NOTE
(1) KIP 7770 is equipped with the Dehumidify Heater.
Using it in high humidity environment (65% or higher) is recommended.
Refer to [2.7 Dehumidifying Roll Media].
(2) “Void of image” and “crease of paper” will occur in case of extremely high or low humidity.
(continued on the next page)
Normal Print
Normal Print
If the media is humidified;
If the media is humidified;
Crease of paper
Loss of image