Kiramek 318-054 User manual

318-054
Dual Stage Shock Sensor
OWNER'S MANUAL
READ BEFORE INSTALLING
WARNING
!
•This product is a 12Vdc device. Do not attempt installation on 24V vehicles.
•
Read all the information in this short Owner's Manual prior to installation.
•
Keep this product away from water, intense heat or humidity, dirt, and flamable liquids. An electrical
short in the presence of a flamable substance can cause severe injury or even death
.
•
Do not attempt installation of this product if you are unfamiliar with automotive eletronics or if you are
no
t absolutely sure of how to connect the wiring. Professional installation by a certified installer
is
highly recommended for safety and proper functionality of the product
.
•
NEVER INSTALL THIS PRODUCT IN THE ENGINE COMPARTMENT!
•
Failure to mount this product in a good location inside the car will result in undesired operation.
•
Do not install this product close to another electronic device that could cause intereference.
•
Kiramek Inc. makes no warranty against theft or vandalism of the vehicle in which this product
is
in
stalled.
• Any damage to this product, to the vehicle, to personal property and any physical injury or death
resulting from accidents, improper use, neglect, faulty wiring, incorrect installation, modification,
alteration or repair outside Kiramek Inc, shall in no way be the responsibility of Kiramek Inc. Kiramek
Inc offers no insurance policy against loss, financial or otherwise.
GENERAL PRECAUTIONS
[PRODUCT WARRANTY ]
1. This product offers a limited 1 year warranty, starting from the original date of purchase. Valid only in Japan.
2.
If the product fails during within the warranty period, with the failure not resulting from misuse, bad installation or after-sale damage, a
free
replacement
will be sent to the dealership from whom the product was originally purchased. Fees may apply for travel or onsite service.
3.
All warranty claims must include both the original sales receipt and defective product, and such must be submitted to the dealership fro
m
whom
the product was originally purchased.
4.
In the event that the original dealership no longer exists, or the dealership has moved, or the dealership refuses to honor the warranty due to
"product
transfer of ownership" reasons, the owner of the product may contact Kiramek Inc. directly to obtain details on warranty replacement.
5.
Warranty replacement where the product is sent to the dealer or Kiramek via mail does not cover postage expenses incured by the customer.
In
addition, this warranty does not cover dealership installation fees that may apply. Consult with your dealer for further details.
6.
Other cases in which this product warranty will not apply:
• Installation error
• Failed product will require unreasonable repairs or installation work
• Decline in product price
• Damage due to fire, earthquake, flood, lightning, saltwater, other natural disasters
• Installation in any vehicle other than normal 12v passenger cars
• No Owner's Manual or Warranty card included with the product (contact your dealer immediately after purchase if this happens)
• Date of purchase, owner's name, and/or seller's information is missing, altered or unreadable
7. This warranty document will not be reissued so please do not throw it away or allow it to be lost.
PLEASE NOTE:
•
This product warranty is limited to defective parts only and does not provide any compensation whatsoever for damages associated with the produ
ct
or
its installation.
•
If you have questions or comments regarding this warranty, please direct your correspondence to the dealership from whom you originally
purchased
this
product.
•
Please fill out the warranty claim form below if your product has failed within the warranty period, and submit it to your dealer. Take care t
o
accurately
fill in the information as mistakes can invalidate your warranty claim.
Ver.Jan.25, 2021
PRODUCT WARRANTY CLAIM
318-05412V SHOCK SENSOR
1 YEAR (validated only by dealer and/or dated proof of purchase)
Year: , Month: , Day:
Name:
Address:
Phone: Email:
Name:
Address:
Phone: Website:
Approval Stamp
Manufacturer:
Contact TEL:
KIRAMEK, Inc.
9-183-1 Itayama-cho,
Handa-shi, Aichi-Ken 475-0936 JAPAN
[phone] ( )
Operating Hours (ex. Sat./Sun./Holidays):
10:00AM ~ NOON, 1:00PM ~ 4:00PM
PRODUCT DESC.:
Warranty Period:
Date of Purchase*:
Customer Info.*:
* Please fill in these marked sections above completely.
NOTE: Warranty Claims not accepted without valid
Approval Stamp and/or dated proof of purchase.
Seller Info.*:
MODEL:
Thank you for purchasing the 318-054 two-stage shock sensor for 12V car security
applications. This sensor will protect your vehicle well for many years if installed and
used properly. Please read this entire manual prior to installation and usage.
CAUTION
!
SAFETY NOTICE
• DO NOT disconnect the vehicle's battery during installation, as it could adversly affect onboard airbag
systems, anti-theft radios or vehicle diagnostics.
• TAKE CARE when installing this sensor. Improper wiring connections can damage vehicle
electronics and/or the sensor itself. The product warranty does not cover improper installation.

INSTALLATION TIPS
SENSITIVITY ADJUSTMENT TROUBLESHOOTING
OPERATION
318-054 FEATURES SPECIFICATIONS
1. To make the Warning Trigger more sensitive, turn the “1st Stage” trigger knob clockwise. Turn it
counterclockwise to decrease sensitivity. (This tells the car alarm to produce Warning Chirps from the Siren.)
2. The Alarm Blast “2nd Stage” Trigger cannot be more sensitive than Warning Trigger because the Warning
Trigger sensitivity knob automatically adjusts the maximum sensitivity of the Alarm Blast Trigger to 80% of the
Warning Trigger setting.
EXAMPLE: Let’s turn the Warning Trigger Sensitivity knob to 50%. Even if you turn the Alarm Trigger
knob all the way to 100%, its sensitivity is still lower than the Warning Trigger range as shown below.
To get more Alarm Trigger sensitivity requires increasing Warning Trigger sensitivity.
This shock sensor detects vibrations in the vehicle body and outputs 2 types of signals based on the strength of
the vibration. Dual sensitivity knobs allow you to cater the trigger thresholds in accordance with the physical
size of your vehicle. See “Sensitivity Adjustment” below for details.
NEVER mount the sensor to metal because the sensitivity will become so high it may false trigger. Install only
on firm plastic parts using the included 2-sided tape. You can even affix the sensor to the outside of the plastic
center column in plain view so long as it’s in a place you won’t accidentally kick.
When parking near a busy road or construction site, if you have the sensitivity set very high (usually
higher than 50%), the sensor may false trigger. Simply reduce sensitivity to solve the problem, or use
the Sensor Bypass feature of your security system to temporarily disable the shock sensor.
NOTE:
Wiring Harness Connection
WIRES
RED
BLK
WHT/RED
ORG
(–)150mA (Max)
4.7mA (Avg.)
(–)150mA (Max)
950ms
400ms
(+)12V Power
(–) Ground
Alarm Blast Trigger Out.
Warning Trigger Output
DESCRIPTION CURRENT PULSE
Alarm Trigger limited to this range
50% 100%
40%
HOW SENSITIVITY KNOBS AFFECT EACHOTHER
WARNING TRIGGER
(“1st Stage”)
←Knob all the way to the LEFT Knob all the way to the RIGHT →
ALARM TRIGGER
(“2nd Stage”)
RF INTERFERENCE:
● Never install RF antennae or mount mobile phones within 20cm of the sensor.
● Never install the sensor or its wire harness near any sources of RF.
● Never tie the sensor wires to other wires because such may case false triggering.
2nd Stage
Trigger
++
–
-
1st Stage
Trigger
●
Affix sensor only to firm plastic, never metal, on the inside of the car using included 2-sided tape.
Clean off oily or dirty surfaces before affixing with 2-sided tape. We recommend brake cleaner or similarly
strong degreaser to ensure the tape sticks and the sensor will never fall off over time. Install only on
flat surfaces. Curved surfaces will cause only part of the tape to stick. Note that if you affix and remove the
sensor & tape multiple times, the tape will weaken and will need to be replaced.
● Never yank hard on the wire harness when attached.
● Avoid installing in these locations:
1. Direct sunlight
2. Near heat sources
3. Anywhere where water could damage the sensor
ELECTRICAL CONNECTION NOTES:
● Connect the sensor directly to a VISION or SCIBORG car alarm using the connector.
● Never T-tap the sensor’s RED or BLK wires for powering something else.
● If you test the sensor after its connected and see no light on the LEDs, check sensitivity
and then check that all sensor connectors are fully seated.
If after checking sensitivity and wiring you find the LEDs won’t light when you tap on the sensor, it
could be the sensing element inside the sensor is rotated out of position. This can happen if the
sensor is dropped or jostled during shipping. Do this to confirm and fix:
1. Disconnect the sensor.
2. Use a small flathead screwdriver to slowly pry open the plastic housing.
3.
If shifted, return the suspended IR reflector to its “NORMAL” position shown below.
4. Close the sensor and reconnect.
NORMAL
504 504
R11 R9 R10 R12
R15
R14
V105
R18
R4
R2
C3
C5 C6 R13
R3
C2
U1
R8
LM324
96AEVXM
G4
054KIR
-0630
R21
C10
R22 R7
R19
U3
TUNG
47
µF
TUNG
504 504
R11 R9 R10 R12
R15
R14
R21
C10
R22 R7
R19
V105
R18
R4
R2
C3
C5 C6 R13
R3
C2
U1
R8
LM324
96AEVXM
G4
U3
C9
C7
TUNG
47
µF
054KIR
-0630
504 504
R11 R9 R10 R12
R15
R14
R21
C10
R22 R7
R19
V105
R18
R4
R2
C3
C5 C6 R13
R3
C2
U1
R8
LM324
96AEVXM
G4
054KIR
-0630
TUNG
47
µF
WRONG POSITION!
Alarm Blast Trigger Indicator
RED LED
Warning Trigger Indicator
GREEN LED
Warning Trigger Sensitivity
Alarm Blast Trigger Sensitivity