Kiramek VISION 2460 Series User manual

© 2018 KIRAMEK, INC., Aichi Japan
Ver. 1.2, NOV. 2018
24V FACTORY KEYLESS SECURITY
2460
series

Thank you for purchasing this VISION
2460 Vehicle Security System. The 2460
is a state of the art device that will pro-
vide you with years of trouble free ser-
vice if used properly. Please familiarize
yourself with the content of this Owner’s
Guide to get the most out of your new
system. We trust you will enjoy using the
product.

© 2018 KIRAMEK, INC.
NOTICE! Although reasonable efforts have been taken to ensure accuracy in this
Owner’s Guide, Kiramek Inc. shall not be held liable for any errors, omissions, prop-
erty damage, or injury resulting from the use of this information.
All product specifications and features are subject to change without notice.
TA B L E O F C O N T E N T S
Limited Lifetime Warranty ................................... 1
Included Items ............................................ 2
Arming & Disarming ....................................... 3
Arming ................................................ 3
Confirmation Chirps .................................... 3
Disarming ............................................. 4
Manual Disarming ...................................... 5
Main Features ............................................ 6
Back Door Trigger ...................................... 6
Door Trigger ........................................... 6
2-Stage Shock Sensor ................................... 6
Ignition Trigger ......................................... 7
Error Chirp ............................................. 8
GWA (Ground When Armed) ............................. 8
SBS (Sector Bypass System) ............................... 8
Status LED & Trigger Memory ............................. 9
Light Flash ............................................. 9
Starter Kill ............................................ 10
Resume .............................................. 10
Valet Mode........................................... 10
Programmable Features ................................... 11
Reset to Factory Defaults ............................... 14
Troubleshooting .......................................... 15
Options ............................ QR CODE ON BACK COVER

1
© 2018 KIRAMEK, INC.
Limited Lifetime Warranty
The VISION 2460 Control Module is backed by a limited lifetime war-
ranty against defective components and/or improper product assem-
bly to the original purchaser for as long the vehicle is owned by that
same purchaser, contingent upon installation by an Authorized VISION
Dealer. All product warranties become void if the VISION 2460 system
was not sold and installed by an Authorized VISION Dealer or the sys-
tem is moved to another vehicle. All other parts and/or accessories
that connect to VISION 2460 systems, including but not limited to the
Starter Kill Relay, LED Program Switch, Shock Sensor, and Siren are
warranted for one (1) year from the original date of purchase.
During the warranty period, Kiramek Inc. will repair or replace, at its
sole discretion, any system component that is found defective in mate-
rial or assembly during the warranty period, provided that the product
is returned to Kiramek Inc. by an Authorized VISION Dealer and is ac-
companied by a clear and legible copy of the original purchaser’s receipt.
Any damage to your VISION 2460 system that results from normal
wear-and-tear, accidents, improper use, neglect, faulty wiring, incorrect
installation, modication, removal or defacement of the product serial
number, alteration or repair outside Kiramek Inc or its Authorized VI-
SION Dealers immediately voids this warranty.
This warranty is limited to defective parts only and does not provide
any compensation whatsoever for damages associated with the VISION
2460 system or its accessories. This warranty does not cover installa-
tion labor, product removal and/or reinstallation fees. This warranty
is valid for the original purchaser only and may not be transferred to
another party. Kiramek Inc makes no warranty against theft or vandal-
ism of the vehicle in which the VISION 2460 system was installed. This
warranty shall not be interpreted as an insurance policy against loss,
nor shall Kiramek Inc be liable any in way for such loss, nancial or
otherwise.
WARNING! DO NOT ATTEMPT TO INSTALL THIS VISION 2460 PRODUCT YOUR-
SELF BECAUSE SUCH WILL IMMEDIATELY VOID THE WARRANTY. THIS SECU-
RITY SYSTEM MUST BE PROFESSIONALLY INSTALLED BY YOUR AUTHORIZED
VISION DEALER TO VALIDATE YOUR WARRANTY.
KIRAMEK may opt to validate the above Warranty, in writing, for shipments outside Ja-
pan, in cases where there is no local VISION Dealer available to perform the install.

2
VISION 2460 OWNER’S GUIDE
INCLUDED ITEMS
LED Program Switch Parts
Status LED
Program Switch
Control Module (1pc)
Shock Sensor (1pc)
(2460B-only)
(2460B-only)
LED Program Sw. (1pc)
Sensor Harness (1pc)
Shock Sensor Tape (1pc)
Starter Kill Relay (1pc)
Window Decals (2pcs)
VISION
IR SHOCK SENSOR
25cm Wire Ties (2pcs)
24V Backup Siren (1pc)
Control Mod. Harnesses (3pcs)
Main
Harness
Guides (2pcs)
24V FACTORY KEYLESS SECURITY
2460
DIGILINK
∞
SMART
24V FACTORY KEYLESS SECURITY
2460
series
DIGILINK
∞
SMART
896H
-
1
C
H
-
D
1
C
o
il:12
VDC
50
A
/
3
0
A
85
86
87
C
1622
3
0
87
a
14
VDC
p/n: 846-1AN
(with coil diode)

VISION 2460 OWNER’S GUIDE
3
Arming & disarming
ARMING
CONFIRMATION CHIRPS
NORMAL ARMING
Close all doors and then LOCK by your factory
keyless remote or by SmartKey door handle
touch. Parking lights may ash, doors will lock,
and the horn/siren will chirp 1 time (if Conrmation
Chirps are ON). The Status LED will light for 5s, dur-
ing which time all triggers are disabled. Then the Sta-
tus LED will start ashing and Ignition, Door, Trunk
and Hood triggers become enabled. The Shock Sensor (and any other exter-
nal sensor) is enabled 5s after the LED starts ashing (10s after you Lock).
SENSOR BYPASS ARMING (2460H does not include a shock sensor)
This procedure lets you temporarily disable
the Shock Sensor (2460B) for a single Arming
session:
1) With Ignition OFF, press the Program Switch twice.
2) Within 20s, press LOCK on the factory remote to Arm.
The system is now Armed in Sensor Bypass Mode, and all triggers are active
except the shock sensor and any other external sensors. Note that when you
Disarm and then Arm again normally, the shock sensor will be enabled.
(ON by default)
This procedure lets you enable or disable the
Arm/Disarm chirps. (Note that the siren will
still go off when the 2460 is triggered.)
1) With Ignition OFF, press the Program Switch once.
2) Within 20s, press LOCK on the factory remote to Arm.
The conrmation chirp state has now toggled and the system is Armed. Re-
peat the above procedure to toggle the conrmation chirp state back again.
PROGRAMMABLE
Vehicles without Factory Keyless require an optional remote.
OFF
OFF
LOCK
2 Pushes
1 Push

© 2018 KIRAMEK, INC.
4
arming & disarming
DISARMING
NORMAL DISARMING
UNLOCK by your factory keyless remote or by
SmartKey door handle touch. Vehicle parking
lights may ash, doors will unlock, the horn/siren
will chirp 3 times (if Conrmation Chirps are ON),
and the Status LED will turn off. The 2460 is now
Disarmed and you may enter the vehicle.
If the horn/siren chirps 4 times when you Disarm, it means something had
triggered while you were away from the vehicle. In this case, the Status LED
will ash to tell you what caused the trigger (see Trigger Memory, page 9).
If you Disable the Ignition Trigger (see pg.11) you can Arm/Disarm
while the engine is running by using an optional remote; however, fac-
tory keyless Lock/Unlock usually won’t work while the Ignition is ON.
DISARMING WITH IG ON
Programmable Feature No.2 prevents Relay Attacks by requiring 2
presses of Unlock on the factory remote to Disarm. See pages 11~12.
THWART RELAY ATTACKS
You cannot Disarm simply by pressing UNLOCK in cases where the
2460’s horn/siren was triggered by the opening of a door or the Ignition
being switched ON. You must follow the above 4-step procedure!
IMPORTANT!
HOW TO DISARM AFTER A DOOR or IGNITION TRIGGER
If the horn/siren is triggered by the opening of a Door or by the
Ignition being switched ON, you must perform the following proce-
dure to Disarm:
1) UNLOCK with factory keyless (with doors/hood/trunk closed).
2) Open the driver’s side door, enter the vehicle, then close the door.
(The horn/siren will blast when you do this, if it is not already blasting.)
3) Ensure the Ignition is OFF, then switch the Ignition ON then OFF.
4) UNLOCK again with factory keyless. The system should now Disarm.
Sensor Trigger, Back Door Trigger or Nothing Triggered.
UNLOCK

5
© 2018 KIRAMEK, INC.
arming & disarming
MANUAL DISARMING
You can manually Disarm using a secure code in the event your
factory remote’s battery dies (see Note 2 below). The factory
code is “6”, but you can change this code to another number of
your choosing for greater security (see the bottom of this page).
1) Enter the vehicle. (The horn/siren will blast. Door can be open or closed.)
2) Turn ON the Ignition.
3) Within 30s, press the Program Switch the same number of times as
your Disarm Code. (Factory Default Code = 6)
4) Turn OFF the Ignition. (The 2460 should Disarm and the horn/siren
should stop.)
1) If the 2460 won’t Disarm in Step-4 above, you entered the code incor-
rectly. Start over from Step-2.
2) Many Push Start vehicles don’t allow the Ignition to be switched on
in the absence of the Factory Remote. So if you lose or destroy your ve-
hicle’s remote, you may not be able to Manually Disarm the 2460. But if
your factory remote merely has a dead battery, you will be able to switch
on the Ignition and Manually Disarm using the 4 steps above.
NOTES
MANUAL DISARM CODE MODIFICATION
The factory code is “6” but you should change it to another number between 1 & 30:
1) With the 2460 Disarmed, switch ON the Ignition.
2) Press the Program Switch for 6s, until the horn/siren will chirp 3 times.
3) Release the Program Switch after you hear the 3 chirps, then turn OFF
the Ignition. The Status LED will light for 5s.
4) Quickly switch ON the Ignition again (while the LED is lit for 5s).
5) When the LED turns off, wait about 5s and you will see the LED start to
ash.
Take note of the ashes as the number of ashes will be the num-
ber of your Disarm Code.
Turn OFF the Ignition to program your code.
The LED will then ash the same number of times as your Disarm Code.
If you added any optional VISION transmitters, you must relearn them.
PROGRAMMABLE

6
VISION 2460 OWNER’S GUIDE
MAIN FEATURES
The horn/siren will blast for 30s when either front
door is opened while Armed. Parking lights may
also ash. A special Disarming procedure is required
when a door is opened while Armed. See bottom half
of page 4 on how to Disarm in this case. Also see
Table-1 on page 9 for Trigger Memory details.
2-STAGE SHOCK SENSOR
1st Stage (“Warning Chirps”). Each time the Shock Sen-
sor detects a light impact to the vehicle body, the siren will
chirp 5 times. However, the Shock Sensor will not trigger
the siren while in Sensor Bypass Mode.
2nd Stage (“Full Trigger”). When the Shock Sensor de-
tects a hard impact to the vehicle body, the horn/siren will
blast for 30s (or until Disarmed with the factory remote).
However, the Shock Sensor will not trigger the siren while
in Sensor Bypass Mode. Also see Table-1 on page 9 for Trig-
ger Memory details.
See pages 15-16 for common shock sensor problems and solutions.
The horn/siren will blast for 30s when the Back Door of
your truck is opened while Armed. Parking lights may
also ash. You can easily Disarm while the siren is
blasting by pressing UNLOCK on your factory keyless
remote. If you Arm with the Back Door left open, it will
be bypassed along with the Shock Sensor (2460B) until
closed. See Table-1 on page 9 for Trigger Memory details.
BACK DOOR TRIGGER
DOOR TRIGGER
5 Chirps
30s Blast
2460B

7
© 2018 KIRAMEK, INC.
main features
IGNITION TRIGGER
Ignition Trigger Enabled (default)
The horn/siren will blast for 30 seconds when
the Ignition (IG) is switched ON while the sys-
tem is Armed, and you cannot Arm when the
Ignition is ON. See bottom half of page 4 on how to Disarm in this case.
Also see Table-1 on page 9 for Trigger Memory details.
Ignition Trigger Disabled (user-programmable)
When the Ignition (IG) Trigger is Disabled, you can
Arm with IG ON. Also, if IG switches ON while al-
ready Armed, the siren will not trigger and instead
Shock Sensor (2460B) and IG triggers are disabled but Door and Back Door
triggers remain enabled. This allows remote starter use and allows you to
run the engine while Armed without triggering the siren. Opening the Door
or Back Door will trigger the siren. The Shock Sensor is re-enabled when
IG goes OFF while Armed. If a front Door was opened while Armed and IG
ON, the siren will trigger, and if IG goes OFF while still Armed, attempts
to turn IG ON will trigger the siren. This intelligent switching is called IIP.
IIP (Intelligent Ignition Protection)
IIP temporarily enables the Ignition Trigger after a horn/siren
trigger caused by a Door-open condition (not the Back Door).
Purpose. Most “remote start compatible” car alarms bypass all trigger
inputs after the Ignition is switched ON. So if a thief opens a door the
siren will trigger; but the thief can then close the door, turn on the Igni-
tion, wait until the siren stops, then drive away in silence because the
Ignition-ON state prevents the siren from triggering again! Yet other
car alarms that always trigger the siren when the Ignition turns ON of-
fer no remote start compatibility at all and not allowing you to sleep in
the vehicle protected with the engine running.
IIP solves this problem.
How it works. If you Disable the Ignition (IG) Trigger, then switch ON
IG (or start the engine) and Arm, all sensors and the IG trigger are dis-
abled but Door and Back Door triggers are active. If the 2460 is Armed
and the horn/siren is triggered by a Door when IG is OFF, IIP automati-
cally Enables the IG Trigger, and the 2460 will trigger the horn/siren
again if IG later goes ON. (Disarming and Arming again will restore
your programmed IG Trigger setting.)
PROGRAMMABLE
IG ON
IG ON
L
O
C
K
A
C
C
O
N
S
T
A
R
T
30s Blast
START
STOP

8
VISION 2460 OWNER’S GUIDE
main features
A “sector” is the Ignition, a Door, the Back Door, or attached Sen-
sors. When a sector triggers the horn/siren a certain number of
times (see below), that sector is bypassed (disabled) until you Dis-
arm and Arm again. This limits noise pollution caused by multiple horn/siren
triggers in a short period of time, such as when you park near construction
sites or if animals jump on the vehicle repeatedly.
DOOR — If either front door is left OPEN, the horn/siren blasts up to
5 times (30s each time), then the Doors are bypassed until closed. The
BACK DOOR WHT/BLK input is bypassed after triggering 10 times.
IGNITION — If the Ignition is left ON, the horn/siren blasts up to 10 times
(30s each time) and then the Ignition is bypassed until you Disarm & Arm again.
SENSOR (2460B) — Warning triggers (5 chirps) and Full Triggers
(30s siren) are independently bypassed after triggering 10 times. You
must Disarm and then Arm again to re-activate.
SBS (Sector Bypass System)
ERROR CHIRP
If a Door or the Back Door is open when you Arm, you will hear 1 chirp (if
Conrmation Chirps are enabled) followed by 2 chirps (even if Conrma-
tion Chirps are disabled). The 2 chirps are Error Chirps that notify you the
door left open won’t trigger the horn/siren, and neither will opening other
doors. But 5 seconds after you close all open doors, the horn/siren will
trigger if you later try to reopen a door. NOTE: Some vehicles don’t allow
factory keyless Lock & Unlock operation when doors are left open.
GWA (Ground When Armed)
The 2460 puts a constant (–)Ground on the Yellow output wire
while the system is Armed. Optional accessories like LED
scanners (visual theft deterrents) can be activated by this con-
trol line while Armed. When the system is Disarmed, the GWA output
becomes an open circuit (NPN transistor switch off and no longer supply-
ing Ground), causing all attached devices to turn off. See the Installation
Guide for electrical specications.
OPTIONAL

VISION 2460 OWNER’S GUIDE
9
main features
The Status LED ashes slowly about once per second while the system is
Armed, acting as a visual theft deterrent. The LED turns off when the
system is Disarmed, unless there was a horn/siren trigger.
TRIGGER MEMORY
The LED ashes rapidly while the full horn/siren blast is going off
and keeps ashing rapidly even after the horn/siren stops. When
you Disarm, the Status LED will change its ashing pattern ac-
cording to Table-1 below, showing you by repeating ashing patterns what
triggered the horn/siren.
If the horn/siren triggered more than once, the LED will show you the
cause of up to the last 3 triggers. For example, if the Back Door was opened
and then a cab Door and then the Ignition was switched ON, the 30s siren
blast would be triggered and on your return to the vehicle, when you Un-
lock, the LED would ash 2 times to indicate a Door was opened, the ash
3 times to indicate the Back Door opened, and the ash 6 times to indicate
the Ignition had been switched ON. Those ashing patterns would then re-
peat on the LED until you either switch ON the Ignition or until you Arm.
STATUS LED
TABLE-1 Status LED Trigger Memory
LED Flashes What Triggered the Horn/Siren
2Door (WHT wire)
3Back Door (WHT/BLK wire)
6Ignition (GRN/WHT wire)
7Sensor (Full Trigger only)
There are no LED Flashes to show if the power was cut and then restored.
LIGHT FLASH
If the GRN output wire is connected, Parking lights will ash continuously
for the entire 30s duration of full horn/siren triggers, and will ash 5 times
when shock sensor Warning Chirps are triggered. NOTE! Some vehicles do
not support Parking light ash unless an optional relay is installed.
OPTIONAL

© 2018 KIRAMEK, INC.
10
Valet mode disables all security system functions, ensuring the horn/siren
will never trigger. Valet Mode is useful when you must hand over your
keys to a valet or maintenance technician, eliminating worry they would
trigger the horn/siren by accident.
Activation:
With the Ignition switched OFF and the 2460
Disarmed, press and hold the Program Switch for more
than 6s, until the Status LED turns OFF. (When the LED
turns OFF, release the Program Switch.)
Deactivation:
Press and hold the Program Switch again
for 6s, until the LED turns OFF. Security features are now restored. (You may
or may not hear 2 quick chirps the rst time you Arm, to inform you that you have
just exited Valet Mode.)
main features
When you activate Valet Mode, the Status LED will not blink and you
will not receive any indication of being in Valet Mode. The security sys-
tem will be completely turned off. This also means that someone could
break into your truck. Our company accepts no liability whatsoever if
your truck is stolen or vandalized or its contents stolen due to your hav-
ing entered Valet Mode. You use this feature at your own security risk.
CAUTION!
Valet Mode PROGRAMMABLE
STARTER KILL
If the YEL/BLK output wire is properly connected to the included Starter
Kill Relay (see Install Guide pg.7), the engine won’t start until the 2460 is
Disarmed. The relay is “normally open,” which means the Starter wire is
broken until the 2460 is Disarmed and the Ignition is switched ON.
RESUME
RESUME is State Memory that remembers if the system was Armed or
Disarmed when the main power is cut. When power is restored, the 2460
will power-up Disarmed if it was Disarmed when the power was cut. If
originally Armed, it will power-up Armed and with the horn/siren blaring.
Push 6s

11
© 2018 KIRAMEK, INC.
11
PROGRAMMABLE FEATURES
You can change some features of the 2460 by using the Program
Switch. Perform the following 5-step procedure to change the fea-
tures shown below in Table-2:
1. Start the engine and then Stop the engine. (Required for Hybrid engines.)
2. With the Ignition OFF, Arm the 2460 and then immediately Disarm.
3. Within 20s, turn ON the Ignition.
4. Press the Program Switch the same number of times as the feature you
want to program — refer to the “No.” column in Table-2 below. (For ex-
ample, to change “Ignition Trigger,” push the Program Switch 3 times.)
5. Turn OFF the Ignition.
TABLE-2 Feature Selection Menu
No. Feature Description Toggle Settings
2 Require 2 Unlocks to Disarm OFF ON
3 Ignition Trigger Enable Disable
4 Parking Lights ON when IG ON OFF ON
5 Error Chirp ON OFF
6 Ignore Factory Unlock (Disarm) Signal NO YES
7 Parking Light Control Solid-ON Flashing
8 Auto Arm OFF ON
9 Horn or Siren Output Pulsed Continuous
10 Auto Rearm OFF ON
17 Exterior Illumination OFF ON
FACTORY DEFAULT SETTINGS SHOWN IN BOLD TEXT ABOVE
1) After you complete Step-5 above, the Status LED will ash the same
number of times as the feature you just programmed. Because the set-
tings merely “toggle,” there’s no indication of the setting you toggled
to. Test your 2460 system to conrm your programmed settings. To
program another setting, repeat the 5 steps above.
2) To Reset to Factory Defaults, see page 14.
NOTES

12
VISION 2460 OWNER’S GUIDE
programmable features
If you Disable the Ignition Trigger and then set this feature to ON, while
the system is Armed, parking lights will illuminate while IG is ON, and
parking lights will turn off when either IG goes OFF or when you Disarm.
4Parking Lights ON when IG ON
When set to Enable (default), the system will trigger the horn/siren when the
Ignition (IG) turns ON while Armed, as described on page 7. NOTE: When
Enabled, you can’t Arm while IG is on, not even with an optional remote.
When set to Disable, the system will bypass the Shock Sensor (2460B) and
Ignition triggers when the Ignition turns ON while Armed. This is useful
if you have a remote engine starter. Also, to sleep in the vehicle with the
engine running, rst start the engine and then Arm using an optional
remote (keyless Lock/Arm doesn’t work when IG is on in most vehicles).
3Ignition Trigger
2Require 2 Unlocks to Disarm
OFF by default. Set to ON to prevent Keyless Relay Attacks*. When ON,
pressing Unlock only 1 time will NOT Disarm. To Disarm you must press
Unlock 2 times on your factory remote within 3 seconds. This prevents
Relay Attacks because even if a Relay Attack thief touches the outside door
handle many times, only one Unlock signal is sent. Unlike the door handle,
your factory remote sends a signal each time you press Unlock on the re-
mote. So pressing 2 times on your outside door handle to Unlock will NOT
Disarm the 2460. You must press Unlock twice on your factory remote.
If you program Feature No.2 to be ON, you then cannot program Feature
No.6 to be ON. Conversely, if you have Feature No.6 programmed to be
ON, you cannot program Feature No.2 to be ON until you turn OFF Fea-
ture No.6. *Relay Attack Info: https://bit.ly/2OFjpnp
If your car has wireless keyless entry (pressing Lock/Unlock on your factory
key locks/unlocks doors) but does NOT allow you to Lock/Unlock by merely
touching the outside door handle, Relay Attacks are impossible on your car
and therefore you can leave Feature No.2 (& No.6) set to OFF.
NOTE

VISION 2460 OWNER’S GUIDE
13
13
programmable features
9Horn or Siren Output
When set to
Continuous
, the system will send a continuous (–)GND out-
put to activate a 24V Siren during 30s Triggers.
When set to
Pulsed
(default), the system will feed a pulsed (–)GND (1A
max.) output. This is needed when connecting to the vehicle’s horn, but it
can also be useful when using a KB24-1 siren with its blue loop wire cut.
This feature automatically Arms the system when you do the following: (1)
turn Ignition ON & OFF then (2) Open & Close any cab Door (not the Back
Door). Upon seeing these events, the system will Arm 20s after the last
cab Door is closed. The doors will NOT be locked so you won’t be locked
out if you leave your keys in the car, but the system will be Armed and will
trigger if any door is opened.
8Auto Arm
7Parking Light Control
When set to Flashing, parking lights ash when Feature No.4 and/or Fea-
ture No.17 are set to ON. When set to Solid-ON, parking lights illuminate
continuously when Feature No.4 and/or Feature No.17 are set to ON.
6Ignore Factory Unlock (Disarm) Signal
Set to YES to stop Keyless Relay Attacks by not Disarming when you press
Unlock. (Ignores the BLU/YEL Door Unlock input.) After you Unlock and
open a door, you have 20s to Disarm either Manually (pg.5) or with an
optional remote, otherwise the horn/siren will blast. NOTE: Feature No.2
is more convenient (see pg.12) if your vehicle can produce 2 unlock pulses.
ON by default. See Error Chirp description on page 8. When set to OFF,
any doors still open when you Arm will be bypassed but you will not hear
the Error Chirp sound to conrm door bypassing. This is useful for vehicles
with automatic sliding doors that take a long time to close.
5Error Chirp

© 2018 KIRAMEK, INC.
14
This feature automatically Rearms the system 60s after it is Disarmed,
unless a Door is opened or the Ignition goes ON during the 60s. Doors will
be locked when the system Rearms.
10 Auto Rearm
If set to
ON
, when you Disarm, parking lights will illuminate for 30s or
until any door is opened or until the Ignition is switched ON, in order to
illuminate the area around the vehicle for greater visibility and security.
NOTE: Exterior Illumination behavior can be adjusted by using Feature
No. 7, Parking Light Control.
17 Exterior Illumination
RESET Programmable Features to Factory Defaults.
NOTE#1: You must reprogram all your optional transmitters after Reset.
NOTE#2: You must know where the 2460 control module is located to Reset.
1. Disarm and ensure Ignition is OFF.
2. Disconnect the 2460’s main harness. (White connector with 6 thick wires.)
3. Push-and-hold the Program Switch.
4. Reconnect the 2460’s main harness. The siren will blast.
5. Release the Program Switch. The siren will stop, LED turns On.
6. Switch ON the Ignition. Horn/Siren will chirp 3 times, LED turns Off.
7. Switch OFF the Ignition. LED will light 5s, then ash 6 times
(Manual Disarm Code resets to 6). RESET complete.
Consult the manual that came with your transmitter (2-way pager or 1-way
3-button remote) to learn how to reprogram them. Also remember that a full
RESET will revert your Manual Disarm Code to “6” (factory default).
NOTE
programmable features

15
© 2018 KIRAMEK, INC.
TROUBLESHOOTING
FACTORY KEYLESS REMOTE WAS LOST, HOW TO DISARM
If the factory remote was lost, you may not be able to Disarm if you have
a Push Start Ignition that requires the presence of the factory remote.
In such a case, you must to contact your dealer for a replacement factory
remote. But if you have an older turn-to-crank style Ignition, you can
Disarm the 2460 by Manual Disarming, as described on page 5.
SOMETIMES CAN’T ARM/DISARM WITH THE FACTORY REMOTE
• On some cars, if you rapidly press Lock and Unlock on the factory re-
mote, the 2460 may stop responding to the remote. In this case the x
is simple — just wait longer between Lock and Unlock presses.
• If Conrmation Chirps (pg.3) are enabled, did you hear a single horn/
siren chip when you tried to Arm? If not, the Ignition may be ON. You
cannot Arm the system while the Ignition is ON unless you have an
optional TR537S or TR365 remote (see “Ignition Trigger” on page 12).
THE SYSTEM IS DEFINITELY ARMED, BUT IT WON’T TRIGGER THE SIREN!
• It may be in Valet Mode. See page 10.
• It may be in Sensor Bypass Mode. See page 3.
HORN/SIREN BLASTS WHEN THE BACK DOOR IS OPENED
• If you need to open the Back Door, rst Disarm the 2460.
• If the Back Door is triggering the horn/siren while Armed, even though
the Back Door is NOT opened, there could be an intermittent connec-
tion to the Back Door on the WHT/BLK wire. Check that connection.
CANNOT DISARM WHILE THE HORN/SIREN IS BLASTING
• You must follow the 4-step procedure “HOW TO DISARM AFTER A
DOOR or IGNITION TRIGGER” on page 4.
• Your factory remote’s battery may be dead. Use Manual Disarming (p5).
SHOCK SENSOR 1st STAGE “WARNING” TRIGGER DOESN’T WORK
Examine the shock sensor and look closely at the two LEDs.
When you lightly tap on the sensor, do you ever see a Green LED light?
• If you never see Green light, adjust the sensitivity knob on the sensor.
• If after increasing sensitivity you still don’t see the Green LED, it
could be that the suspended element inside the sensor body was shifted
out of place. See page 15 in the Install Guide on how to resolve this.
• If you do see a Green light, the sensor is functioning properly. That
means there is like a wiring problem. Check that the sensor wire har-
ness is properly connected at both ends.

16
VISION 2460 OWNER’S GUIDE
30s HORN/SIREN BLAST OCCURS WITH LIGHT IMPACT TO THE VEHICLE
• You mounted the shock sensor (2460B) to metal. Remount on a rm
plastic part of the vehicle.
• Turn down the shock sensor sensitivity to 50% or less.
• Check your Shock Sensor wire harness, end-to-end from the sensor
itself to the 2460 control module, and ensure no other wires are touch-
ing or in close proximity to it (some wiring can cause interference that
can false trigger the shock sensor). Also make sure no RF transmitting
devices are in close proximity to the shock sensor or its wire harness.
• If you added an optional Ultrasonic sensor, it is very likely that the
controller of the ultrasonic sensor (not the emitters) was placed too
close to the shock sensor. The Ultrasonic sensor’s controller should be
placed more than 30cm (1 foot) away from the shock sensor to avoid
interference.
CAN’T ARM WITH IGNITION ON
Even if you programmed the Ignition Trigger to be Disabled (see page
11), you cannot Arm using the factory remote Lock button while the
Ignition is ON. However, if you purchase the optional TR537S 2-way
paging system or the TR365-series 1-way remote, you will then be able
to Arm with the Ignition ON if the Ignition Trigger is set to be Disabled.
(NOTE! Even with the optional remote, you cannot Arm with IG ON if
the Ignition Trigger is Enabled.)
CAN’T START ENGINE
• Is the included Starter Kill Relay installed? If installed and if you
also have Ignition Trigger DISABLED, the Ignition can be switched
ON even while Armed and the Siren won’t trigger; but when you try
to start the engine while the 2460 is Armed, the Starter Kill relay will
prevent starting. First Disarm the 2460, then start the engine.
• It could be low voltage. Has it been a long time (about a month) since
you started the engine? If you have an optional remote attached and
have not started your engine in several weeks, it could be that your
vehicle battery voltage is too low. Check your vehicle battery voltage
and charge if necessary. You may not be able to start your engine if
the battery voltage is lower than 22V. Even if your battery voltage is
24V you still could have a bad 24V battery or bad 12V battery pair.
The 2460 and attached sensors and remotes will continue operating if
the vehicle battery voltage falls as low as 8.5V, but any 24V relays you
may be using usually won’t work below 12.5V. If battery voltage falls
below 8.5V, 2460 sensors will stop working, and below 5.5V the 2460
CPU will stop and all security functions will shutdown.
TROUBLESHOOTING

9-183-1 Itayama-cho, Handa-shi, Aichi-Ken 475-0936 JAPAN
VISION products are engineered in Japan and manufactured in
strict accordance with Japanese QC standards at an ISO9000/
QS9000 certified factory.
Add-on sensors, remotes and installation parts can be found on our website:
www.visionsecurity.jp/en/
This manual suits for next models
1
Table of contents
Other Kiramek Security System manuals
Popular Security System manuals by other brands

Call Aid UK
Call Aid UK 1155 Series Installation & user manual

Tyco Security Products
Tyco Security Products DSC Power Series installation guide

M-system
M-system AS instruction manual

Swann
Swann SW231PC4 operating instructions

SILENTRON
SILENTRON Sil Bus Instructions and warnings for installation and use

BT Redcare
BT Redcare 3GSTU-12V User's installation guide