Kistler 5181A Series User manual

Instruction
Manual
Differential charge
amplifier
Type 5181A…
ä
5181A_002-748e-06.20

Foreword
5181A_002-748e-06.20 Page 1
Foreword
Thank you for choosing a Kistler quality product
characterized by technical innovation, precision and long
life.
Information in this document is subject to change without
notice. Kistler reserves the right to change or improve its
products and make changes in the content without
obligation to notify any person or organization of such
changes or improvements.
© 2015 … 2020 Kistler Group. Kistler Group products are
protected by various intellectual property rights. For more
details visit www.kistler.com. The Kistler Group includes
Kistler Holding AG and all its subsidiaries in Europe, Asia,
the Americas and Australia.
Kistler Group
Eulachstrasse 22
8408 Winterthur
Switzerland
Tel. [phone]
[e-mail]
www.kistler.com

Differential charge amplifier Type 5181A…
Page 2 5181A_002-748e-06.20
Content
1. Introduction ................................................................................................................................... 3
2. Important information.................................................................................................................... 4
2.1 Protection and standards...................................................................................................... 4
2.2 Disposal instructions for electrical and electronic equipment ................................................ 4
2.3 Precautions........................................................................................................................... 5
3. Product description ........................................................................................................................ 6
3.1 Differential charge amplifier Type 5181A… ......................................................................... 6
3.2 Technical data ...................................................................................................................... 6
3.3 Execution options ................................................................................................................. 7
3.4 Version with aluminum die-cast enclosure, Type 5181AA… ................................................ 8
3.4.1 Electrical connections............................................................................................... 9
3.4.1.1 Sensor ...................................................................................................... 9
3.4.1.2 Power/output ........................................................................................ 10
3.5 Version with DIN-rail enclosure, Type 5181AB… ............................................................... 14
3.5.1 Electrical connections............................................................................................. 14
3.6 Ordering key ...................................................................................................................... 18
4. Installation ................................................................................................................................... 19
4.1 Version with aluminum die-cast enclosure, Type 5181AA… .............................................. 19
4.2 Version with DIN-rail enclosure, Type 5181AB................................................................... 23
5. Calibration and repair .................................................................................................................. 24
5.1 Calibration.......................................................................................................................... 24
5.2 Repair................................................................................................................................. 24
6. EC Declaration of Conformity ...................................................................................................... 25
Total pages 25

Introduction
5181A_002-748e-06.20 Page 3
1. Introduction
Thank you for choosing a quality product from Kistler.
Please read through this manual thoroughly to enable you
to fully exploit the various features of your product.
These instructions describe the differential charge amplifier
Type 5181A.
Performance features at a glance:
Voltage or current output option
Wide charge conversion range
High pass / low pass filter options
Plastic DIN-rail or aluminum die-cast enclosure
To the extent permitted by law Kistler accepts no liability if
this instruction manual is not followed or products other
than those listed under accessories are used.
Our product and application brochures, in addition to our
detailed data sheets, will provide you with an overview of
our product range.
If you require additional assistance beyond what can be
located online or in this manual, please contact Kistler‘s
extensive support organization or visit us online at
www.kistler.com/thermoacoustics.

Differential charge amplifier Type 5181A…
Page 4 5181A_002-748e-06.20
2. Important information
2.1 Protection and standards
All equipment is tested and has left the factory in a
perfect, safe condition. In order to maintain this
condition and ensur
e safe operation, compliance is
requi
red with the instructions and warning notes
contained within this manual or imprinted on the
product itself.
The instruments are CE-compliant within the meaning of
ISO 9001
2011/65/EU (ROHS)
2014/30/EU (EMC)
Emmission EMC
EN 61000-6-3:2007 + A1:2011
EN 61000-6-4:2007 + A1:2011
EN 61326-1:2013 (Class A+B equipment)
Immunity EMC
EN 61000-6-1:2007
EN 61000-6-2:2005
EN 61326-1:2013 (Class A+B equipment)
Compliance with local safety regulations, which may apply
to the use of power line operated electrical and electronic
equipment, is strongly recommended.
2.2 Disposal instructions for electrical and electronic equipment
Do not discard old electronic instruments in municipal
trash. For disposal at end of
life, please return this
product to an authorized local electronic waste disposal
service or contact the nearest Kistler Instrument sales
office for return instructions.

Important information
5181A_002-748e-06.20 Page 5
2.3 Precautions
Compliance with the following precautionary measures
is vital to ensure safe and reliable operation: Check all
equipment packaging for transportation damage.
Report any damage to the freight forwarder and to
Kistler.
The equipment should be used only under the specified
operating conditions.
If there is evidence that safe operation is no longer possib-
le, the instrument must be powered off and rendered safe
against accidental start-up.
Safe operation is no longer possible when the product
shows visible signs of damage
is no longer operating
has been subjected to prolonged storage under
unsuitable conditions

Differential charge amplifier Type 5181A…
Page 6 5181A_002-748e-06.20
3. Product description
The differential charge amplifier is suitable for differential
ground isolated measuring chains.
3.1 Differential charge amplifier Type 5181A…
The differential charge amplifier converts the charge signal
of differential piezoelectric sensors into voltage or current.
The 18 … 30 VDC supply voltage is galvanically separated
which prevents ground loop issues. The internal compen-
sation electronics eliminates the drift of the amplifier and
compensates low frequency error-currents up to 5 nA.
3.2 Technical data
The technical data of the differential charge amplifier are
contained in the official data-sheet (doc. no. 003-227).

Product description
5181A_002-748e-06.20 Page 7
3.3 Execution options
Differential charge amplifier Type 5181… is the non-Ex
version out of the product family 5181/83/85 (non-Ex,
Ex-ia, Ex-nA). This product family is highly flexible. The
different execution options can be seen in the ordering
key. All configurations are pre-set at the factory.
Conversion factor
The charge amplifier has a selectable range for the
conversion factor and contains no reset-function but a
high-pass filter (time constant) in the input stage.
Signal output options
There are different voltage- or current outputs available.
Enclosure options:
1. Aluminum die-cast enclosure
Free choice of installation location, which allows shorter
connecting cables
Robust, sealed, no extra enclosure needed
Connection to charge amplifier
With connector or
Cable gland and terminals for wire connection
2. DIN-rail enclosure is suitable for high channel count.
The enclosure is made of plastic and meets IP30.
Lower cost
Low space required
Simple connection with terminal blocks

Differential charge amplifier Type 5181A…
Page 8 5181A_002-748e-06.20
3.4 Version with aluminum die-cast enclosure, Type 5181AA…
Several options which can be freely chosen are available for
the connections to the charge amplifier.
Sensor side: connector or cable gland and terminals
Power / output side: connector or cable gland and
terminals
Fig. 1: Dimensions of differential charge amplifier with
aluminum die-cast enclosure
Type 5181AA…

Product description
5181A_002-748e-06.20 Page 9
3.4.1 Electrical connections
3.4.1.1 Sensor
Sensor
Pin
Description
1
SGND
2
SGND
3
Qin+
4
Qin–
Type: 5181AA_C_ connection with connector
Sensor
Pin
Description
1
Qin–
2
SGND
3
Qin+
Type: 5181AA_P_ installation of cable with cable gland
Fig. 2: Connection of sensor cable

Differential charge amplifier Type 5181A…
Page 10 5181A_002-748e-06.20
3.4.1.2 Power/output
Power supply / signal output
Pin
Description
1
EXC+
2
EXC–
3
SGND
4
Signal+
5
Signal–
6
SGND
Type: 5181AA__C connection of cable with connector
Power supply
Pin
Description
1
EXC+
2
EXC–
3
SGND
Signal output
Pin
Description
4
Signal+
5
Signal–
6
SGND
Type: 5181AA__P
installation of cable with cable gland
Fig. 3: Connection of power/output cable
M16-device plug 6pol m
Type:

Product description
5181A_002-748e-06.20 Page 11
Bild
b
: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Differential charge amplifier Type 5181A…
Page 12 5181A_002-748e-06.20
Bild b: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Product description
5181A_002-748e-06.20 Page 13
Bild b: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Differential charge amplifier Type 5181A…
Page 14 5181A_002-748e-06.20
3.5 Version with DIN-rail enclosure, Type 5181AB…
The charge amplifier version with the DIN-Rail enclosure is
suitable for high channel count. The enclosure is made of
plastic and meets IP30.
Fig. 4: Dimensions of differential charge amplifier with
DIN-Rail enclosure
3.5.1 Electrical connections
Sensor
Pin
Description
1
Qin
+
2
Qin–
3
SGND
4
EARTH
Static sensitive
input-precautions
required!
Power supply/auxiliary
Pin
Description
5
NC
6
EARTH
7
EXC+
8
EXC–
Signal output
Pin
Description
9
Signal+
10
Signal–
11
SGND
12
EARTH
Fig. 5: Electrical connections

Product description
5181A_002-748e-06.20 Page 15
Bild b: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Differential charge amplifier Type 5181A…
Page 16 5181A_002-748e-06.20
Bild b: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Product description
5181A_002-748e-06.20 Page 17
Bild b: Anschlussschema, abhängig von der galvanischen Trennung von DAQ und Stromversorgung

Differential charge amplifier Type 5181A…
Page 18 5181A_002-748e-06.20
3.6 Ordering key