Kistler 2519A Series User manual

Instruction
Manual
Data Evaluation and
Reference Manual
Transient Recorder
Type 2519A…
Software
TR Control
2519A_002-607e-10.12

Instruction
Manual
Data Evaluation and
Reference Manual
Transient Recorder
Type 2519A…
Software
TR Control
2519A_002-607e-10.12

Foreword
2519A_002-607e-10.12 Page 1
Foreword
Thank you for choosing a Kistler quality product
characterized by technical innovation, precision and long
life.
Information in this document is subject to change without
notice. Kistler reserves the right to change or improve its
products and make changes in the content without
obligation to notify any person or organization of such
changes or improvements.
©2012 Kistler Group. All rights reserved. Except as
expressly provided herein, no part of this manual may be
reproduced for any purpose without the express prior
written consent of Kistler Group.
Kistler Group
Eulachstrasse 22
8408 Winterthur
Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.kistler.com

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 2 2519A_002-607e-10.12
Content
1. Introduction ................................................................................................................................... 3
1.1 Disposal Instructions for Electrical and Electronic Equipment ................................................ 4
1.2 Software Upgrades and Updates.......................................................................................... 4
2. Data Evaluation.............................................................................................................................. 5
3. Reference Instructions.................................................................................................................. 21
3.1 TR 2519: Block Diagram..................................................................................................... 21
3.2 TR 2519: Technical Specifications....................................................................................... 22
3.3 TR 2519: Description of Front and Rear Panel.................................................................... 25
3.3.1 Front Panel............................................................................................................ 25
3.3.2 Rear Panel ............................................................................................................. 26
3.4 Detailed Description of All Functions of Control Program................................................... 27
3.4.1 Main TR 2519 Control Window ............................................................................ 27
Menu File............................................................................................... 283.4.1.1
Menu Edit .............................................................................................. 383.4.1.2
Menu Calibration ................................................................................... 393.4.1.3
Menu Measurement .............................................................................. 433.4.1.4
3.4.1.4.1 Target Background ................................................................................................ 48
Real Diameter of Hits and Shot Numbers in Target Picture .................... 503.4.1.5
Menu Graphs and Computing ............................................................... 513.4.1.6
Menu Select........................................................................................... 663.4.1.7
Menu Settings........................................................................................ 673.4.1.8
Menu Help............................................................................................. 723.4.1.9
3.4.2 TR 2519: Panel of Virtual TR 2519 ........................................................................ 73
Total pages 78

Introduction
2519A_002-607e-10.12 Page 3
1. Introduction
Please take the time to thoroughly read this instruction
manual. It will help you with the installation, maintenance,
and use of this product.
To the extent permitted by law Kistler does not accept any
liability if this instruction manual is not followed or
products other than those listed under Accessories are
used.
Kistler offers a wide range of products for use in measuring
technology:
Piezoelectric sensors for measuring force, torque, strain,
pressure, acceleration, shock, vibration and acoustic-
emission
Strain gage sensor systems for measuring force and
torque
Piezoresistive pressure sensors and transmitters
Signal conditioners, indicators and calibrators
Electronic control and monitoring systems as well as
software for specific measurement applications
Data transmission modules (telemetry)
Kistler also develops and produces measuring solutions for
the application fields of engines, vehicles, manufacturing,
plastics and biomechanics sectors.
Our product and application brochures will provide you
with an overview of our product range. Detailed data
sheets are available for almost all products.
If you need additional help beyond what can be found
either on-line or in this manual, please contact Kistler's
extensive support organization.

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 4 2519A_002-607e-10.12
1.1 Disposal Instructions for Electrical and Electronic Equipment
Do not discard old electronic instruments in municipal
trash. For disposal at end of life, please return this
product to an authorized local electronic waste disposal
service or contact the nearest Kistler Instrument sales
office for return instructions.
1.2 Software Upgrades and Updates
Kistler may from time to time supply upgrades or updates
for embedded software. Such upgrades or updates must
always be installed.
Kistler declines any liability whatsoever for any direct or
consequential damage caused by products running on
embedded software which has not been upgraded or
updated with the latest software supplied.

Data Evaluation
2519A_002-607e-10.12 Page 5
- measurement of time intervals (between each curves)
- measurement of velocity (by use of known base)
- independent selection of rising or falling edges
- independent setting of threshold levels
- time filter for elimination of shockwaves
(between two edges)
Time Interval & Velocity
THRESHOLD
LEVEL
t
2. Data Evaluation

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 6 2519A_002-607e-10.12
- measurement of time intervals (between each curves)
- measurement of velocity (by use of known base)
- independent selection of first zero-crossing after
crossing of the threshold level from left to right
or from right to left direction
- time filter for elimination of shockwaves
(between two zero-crossings)
Time Interval & Velocity
THRESHOLD
LEVEL
t

Data Evaluation
2519A_002-607e-10.12 Page 7
- measurement of time intervals (between each curves)
- measurement of velocity (by use of known base)
- program determines time interval between rising edges
of start integral curve and stop integral curve
- especially designed for measurement of velocity by use
of centre of gravity (pellets etc.)
()by use of integral
Time Interval & Velocity
THRESHOLD
LEVEL
t

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 8 2519A_002-607e-10.12
- measurement of curve maximum (Pmax etc.)
- measurement of time position of maximum
(time interval between accelerometer and Pmax)
- filter for noise supression
(and time position of maximum)
Maximum Value of Curve
Pmax
t

Data Evaluation
2519A_002-607e-10.12 Page 9
- measurement of integral (area) of curve between
two cursors
(between two cursors)
Integral of Curve
AREA
t

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 10 2519A_002-607e-10.12
- measurement of integral (area) of curve between
two events (see picture) : start of integration is derived
from accelerometer signal (yellow curve), stop
is derived from muzzle sensor (green curve)
- independent selection of rising or falling edges
- time filter for noise supression
(between two events)
Integral of Curve
AREA
t

Data Evaluation
2519A_002-607e-10.12 Page 11
- measurement of derivation (slope, dy/dt) of curve
between two cursors
(between two cursors)
Derivation of Curve
dy
dt

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 12 2519A_002-607e-10.12
- measurement of derivation (slope, dy/dt) of curve
between two levels (in % of curve maximum)
- each level is adjustable in range 0-100%
- designed for easy measurement of curve slew rate
(between two levels)
Derivation of Curve
10% Pmax
90% Pmax
dy
dt Pmax

Data Evaluation
2519A_002-607e-10.12 Page 13
- measurement of Rate Of Fire between all
consecutive shots
- measurement of velocity (by use of known base)
for all shots
- independent selection of rising or falling edges
- independent setting of threshold levels
- time filter for elimination of shockwaves
(between two consecutive shots)
Rate Of Fire
THRESHOLD
LEVEL
ti

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 14 2519A_002-607e-10.12
- measurement of hit position and target velocity
by use of electronic target system DTS01/02
- ratio of intervals t1 and t2 determines X (or Y)
coordinate of hit
- independent selection of rising or falling edges,
threshold levels and shockwave filters for X and
for Y coordinate
(2x DTS01/02)
Target System
THRESHOLD
LEVEL
t2
t1

Data Evaluation
2519A_002-607e-10.12 Page 15
- measurement of function value of curve Y=f(X)
for entered fixed value of X
(Y = f(X) for fixed value of X)
Function Value of Curve
Y= (X)f
X

Data Evaluation and Reference Manual Transient Recorder Type 2519A…
Page 16 2519A_002-607e-10.12
- measurement of function value of curve Y=f(X)
at event X (rising or falling edge of impulse)
(Y = f(X) )at event
Function Value of Curve
Y= (X)f
X

Data Evaluation
2519A_002-607e-10.12 Page 17
-
-
testing of shape of curve (Pass / Fail)
unlimited number of masks with save/load option
(PASS / FAIL testing)
Limit Mask
MIN
MAX