KitchenAid KRWS 9010 User manual

KRWS 9010
Assembly instructions
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 1

5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 2

Installation kit supplied 4
Wine drawer overall dimension 5
Installation kit 6
Preparation of the cabinet for inserting the wine drawer 8
Fitting the two brackets supplied in the installation kit 9, 10
Inserting the wine drawer in the cabinet 13
Inserting the corrugated plastic sheet covering 16
Installation completed 17
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 3

The wine drawer is designed for built-in installation and must not be used as a free-standing unit.
Installation and maintenance must be carried out by at least two qualified technicians.
INSTALL THE WINE DRAWER ONLY IN POSITION UNDER THE KITCHEN WORKTOP.
Make sure the wine drawer is fixed to the adjacent cabinet with the brackets supplied.
DO NOT INSTALL THE WINE DRAWER IN A COLUMN.
DO NOT INSTALL THE WINE DRAWER ON ITS OWN OR IN A SINGLE CABINET.
Otherwise the wine drawer will be unstable, with risk of tipping over and consequent injury or damage.
Do not start this electrical appliance if it is damaged, does not work properly, is partially disassembled or if
there are broken or missing components, including damaged cable or power socket.
Make sure the power cable is in a position where it cannot be trodden on, tripped over, damaged or
undergo strain.
Do not install or store the appliance in places where it can be exposed to bad weather or temperatures
below freezing.
The min. area in the base board for the passage of air must be at least 200 cm2.
Installation kit supplied
4
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 4

5
Wine drawer overall dimension
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 5

6
SCALE 1:1
N°2 BRACKET
SCALE 1:5
SCALE 1:2
SCALE 1:2 SCALE 1:5 SCALE 1:1
N°1 COVERING IN CORRUGATED PLASTIC SHEE
T
N°2 SIDE ADHESIVE
N°1 TEMPLATE
N°6 SCREW 4.2x13 UNI 6954-71 B
N°14 SCREW 4.8x15 UNI 6955-71 AB
Installation kit
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 6

7
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 7

8
VERT.
VERT.
16 MIN.
CHAMFER 014x3.6
16 MIN.
50 MIN.
550 MIN.
VERT.-VERT. SECTION
SECTION F-F SCALE 1:1
680 MIN.
316 MIN.
100 100 100 100
F
F
81.5
Preparation of the cabinet for inserting the wine drawer
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 8

Fitting the two brackets supplied in the installation kit
9
316 MIN.
340 MAX.
60
VERT.-VERT SECTION
VERT.
VERT.
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 9

10
BRACKET
N°10 SELF-TAPPING SCREWS 4.8x 15 UNI 6955-71B
Fitting the two brackets supplied in the installation kit
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 10

11
N°2 SIDE ADHESIVE
SCALE 29:200
SCALE 29:200
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 11

12
VERT.
VERT.-VERT. SECTION
SEE DETAIL X
VERT.
SEE DETAIL Y
DETAIL X
SCALE 1:1
354 MIN.
DETAIL Y
SCALE 1:1
897
897
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 12

Inserting the wine drawer in the cabinet
13
N°6 SCREWS UNI 6954-7IB 4.2x13
MIN. 200 Cm2
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 13

14
SEE DETAIL X
DETAIL X SCALE 1:2
TEMPLATE
1. INSERT THE WINE DRAWER IN THE CABINET
POSITIONING IT SO THAT THE DRAWER SEAL EDGE IS 44 mm. FROM THE FRONT SIDE OF THE CABINET USING THE SPECIAL TEMPLATE SUPPLIED.
2. THEN FIX THE WINE DRAWER TO THE CABINET WITH THE SCREWS SUPPLIED.
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 14

15
CUT AND BEND
SCALE 33:200
SCALE 33:200
REPARATION OF THE CORRUGATED PLASTIC SHEET COVERING SUPPLIED IN THE INSTALLATION KIT
B1 B2 B3 B4
AB
704
716
717
720
722
728
850
1 2 2 2 2 3 4
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 15

4 SCREWS 4.8x 15 UNI 6955-71 AB
Inserting the corrugated plastic sheet covering
16
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 16

17
Installation completed
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 17

5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 18

5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 19

5019 102 00270
Printed in Italy n
11/07
GB
5019_102_00270_INSTAL_GB 6-11-2007 10:45 Pagina 20