Klein Tools MM6000 User manual

GRAPHICS DRAWING NAME: MM6000 Manual ENG.indd
GRAPHICS PART NUMBER: XXXXXX ECN NUMBER.: 00000
PACKAGING DWG. REF.: VENDOR SUPPLIED Revision: A 10.11.12
ENGLISH
www.kleintools.com
Instruction
Manual
For Professionals...Since 1857
®
ENGLISH
MM6000
• TRUERMS
• BACKLITDISPLAY
• BARGRAPH
• LEADSTORAGE
• MAX/MIN
• 3-5/6DIGIT
6000COUNTLCD
• AUTO/MANUAL
RANGE
• AUTOHOLD
HOLD
Apo
AUTO
RANGE
TRMS
A-HOLD
SYMBOLSUSEDONLCD
~
ACMeasurement DCMeasurement
-
NegativeDCValue
AT
AutoRangeActive
O .L.
Overload:RangeExceeded Apo AutoPower-OffActive
LowBattery
HOLD
HoldActive
MIN
MinimumReading
M AX
MaximumReading
%
DutyCycleMode FrequencyMode
V
VoltageMeasurement
A
CurrentinAmps
Ω
ResistanceinOhms DiodeTest
F
CapacitanceinFarads ContinuityTest
Relative/ZeroMode
n
Nano10
-9
µ
Micro10
-6
m
Milli10
-3
k
Kilo10
3
M
Mega10
6
°F
DegreesFahrenheit
°C
DegreesCelsius
A- HOLD
Auto-HoldActive
LOW
Z
LowImpedance
ELECTRICALSPECIFICATIONS
DCVoltageMeasurement
Range Resolution Accuracy
600mV ˜ 600V 0.1mV ˜ 0.1V ± (0.2% + 5 digits)
1000V 1V ± (0.5% + 10 digits)
OverloadProtection: 1000V InputImpedance(Nominal): >10MΩ, <100pF
InputImpedance(LOWZ): >3kΩ, <200pF, up to 600V RMS
ACVoltageMeasurement
Range Resolution Accuracy
40Hz ~ 400Hz
Accuracy
400Hz ~ 2kHz
600mV 0.1mV
± (0.75% + 5 digits)
± (2.5% +10 digits)
6V ~ 600V 1mV ~ 0.1V ± (2.0% + 8 digits)
1000V 1V ± (0.75% + 8 digits) ± (2.0% +8 digits)*
Continued on next page.
OverloadProtection: 1000V RMS InputImpedance(Nominal):>10MΩ, <100pF
InputImpedance(LOWZ): >3kΩ, <200pF, up to 600V RMS
FrequencyResponse: 40 to 2kHz Response: True RMS
*Accuracy for 400Hz ~ 1kHz range only.
DCCurrentMeasurement
Range Resolution Accuracy
600µA ~ 400mA 0.1µA ~ 0.1mA ± (1.0% + 5 digits)
6A ~ 10A 1mA ~ 10mA ± (1.5% + 5 digits)
OverloadProtection:µAmA:400mA (F440mA/1000V fuse) /AInput:10A(F11A/1000V fuse)
ACCurrentMeasurement
Range Resolution Accuracy
40Hz ~ 2kHz
600µA ~ 400mA 0.1µA ~ 0.1mA ± (1.2% + 5 digits)
6A ~ 10A 1mA ~ 10mA ± (1.8% + 5 digits)
OverloadProtection:µAmA:400mA (F440mA/1000V fuse) /AInput:10A(F11A/1000V fuse)
Frequency: 40 to 2kHz Response: True RMS
ResistanceMeasurement
Range Resolution Accuracy
600Ω˜6MΩ0.1Ω˜0.001MΩ± (1.0% + 5 digits)
50MΩ0.01MΩ± (1.5% + 10 digits)
OverloadProtection: 600V RMS
CapacitanceMeasurement
Range Resolution Accuracy
60nF 0.01nF
± (3.5% + 6 digits)
600nF ~ 6000µF 0.1nF ~ 1µF
OverloadProtection:600V RMS
FrequencyMeasurement
Range Resolution Accuracy
99.99Hz ˜399.9kHz 0.01Hz ˜0.1kHz ± (0.1% + 3 digits)
OverloadProtection: 600V RMS Sensitivity: 2.5V RMS
DutyCycleMeasurement
Range Resolution Accuracy
1.0 ˜99.0% 0.1% ± (0.2% per kHz + 0.1% + 8 digits)
OverloadProtection: 600V RMS Sensitivity: < 50V RMS
FrequencyRange: 0.5Hz to 10kHz
DiodeTest
OverloadProtection Range TestCurrent OpenCircuitVoltage
600V RMS 6.0V DC 0.25mA <1.8V DC
ContinuityTest
OverloadProtection OpenCircuitVoltage Threshold(Appx.)
600V RMS <0.44V <40Ω
TemperatureMeasurement
Range Resolution Accuracy
-58 ~ 600°F 0.1°F ± (1.0% + 5.4°F)
-50 ~ 600°C 0.1°C ± (1.0% + 3.0°C)
600 ~ 1832°F 1°F ± (1.0% + 5.4°F)
600 ~ 1000°C 1°C ± (1.0% + 3.0°C)
OverloadProtection: 600V RMS K-typeThermocoupleAccuracy: Not specified
Specifications subject to change.

WARRANTY
See www.kleintools.com, contact Klein Tools at 1-877-775-5346, or visit a
distributor for warranty information.
CLEANING
Turn instrument off and disconnect test leads. Clean the instrument by using
a damp cloth. Do not use abrasive cleaners or solvents.
STORAGE
Remove the batteries when instrument is not in use for a prolonged period
of time. Do not expose to high temperatures or humidity. After a period of
storage in extreme conditions exceeding the limits mentioned in the General
Specifications section, allow the instrument to return to normal operating
conditions before using it.
DISPOSAL/RECYCLE
Caution:This symbol indicates that equipment and its accessories
shall be subject to a separate collection and correct disposal.
CUSTOMERSERVICE
 DONOTapplyvoltagetothermocouple.
• Fahrenheit range: -58° to 1832°F (Celsius range: -50° to 1000° C).
8. Temperature:
Features:
MAX/MIN RELHOLD
TestingFuse:
• When selecting uA or mA/A functions the meter will indicate
“LEAd” if the test leads are not properly connected to the meter.
• Note: This message remaining on the screen after properly
connecting the test leads is an indication that the fuse is open.
KLEINTOOLS,INC.
450 Bond Street
Lincolnshire, IL 60069
1-877-775-5346
www.kleintools.com
Rev A 1/13 139750
7. Frequency(Hz)/DutyCycle:<400kHz
Features:
HOLD
6. LowImpedance(LOWZ):<600V
 DONOTuse(LOWZ)modeatvoltagesgreaterthan600V.
• Press SELECT to choose AC or DC Voltage.
• Use Low Impedance (LOW Z) mode to reduce ghost voltages.
• See AC/DC Voltage instruction.
Capacitance Features:
HOLD
 Safelydischargecapacitorbefore
measurement.
• Reading may take up to 60 seconds
for large capacitors.
AUTOHOLD
4007036

ENGLISH
FEATUREDETAILS
MM6000
InstructionManual
GENERALSPECIFICATIONS
The Klein Tools MM6000 is a True RMS, auto-ranging multimeter.
It measures AC/DC voltage, low impedance voltage, AC/DC current,
resistance, capacitance, frequency, duty cycle, and temperature. It can also
test diodes and continuity.
• OperatingAltitude:6562 ft / 2000 m
• RelativeHumidity:<75%
• OperatingTemperature:O°C/32°F to 45°C/113°F
• StorageTemperature:-20°C/ -4°F to 60°C/140°F <80% R.H.
• AccuracyTemperature:18°C/64°F to 28°C/82°F
• TemperatureCoefcient: 0.1*(specified accuracy)/ °C
• SamplingFrequency:3 samples per second
• Dimensions: 7” x 3.5” x 1.875”
• Weight:14 oz.
• BatteryLife:160 Hours
• Calibration:Accurate for one year
• Accuracy:± (% of reading + # of least significant digits)
• CATRating:CAT III 1000V, CAT IV 600V
• Certications:Conforms to UL Stds 61010-1 & 61010-2-030.
Certified to CAN/CSA C22.2 No.61010-1, 61010-2-030,
IEC 61010-2-030:2010 MOD, ANSI/ISA-61010-2-030 (82.02.03).
• PolutionDegree:2
• CountryofOrigin:USA (of US and imported parts)
WARNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring a known
voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from the
metal probe contacts when making measurements.
• Do not open the meter to replace batteries or fuses while the probes
are connected.
• Use caution when working with voltages above 60V DC or 25V AC
RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock, replace
batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out power
before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
SYMBOLS
~
ACAlternatingCurrent WarningorCaution
DCDirectCurrent DangerousLevels
DC/ACVoltageorCurrent DoubleInsulatedClassII
Ground ACSource
C
E
A
G
F
D
H
J
I
M
L
K
N
B
5
1
8
3
4
6
7
2
1. ACVoltage:<1000V.(LOWZ)<600V
Features:
MAX/MINRANGEHOLDREL
 DONOTattempttomeasuremorethan1000V.
 DONOTuse(LOWZ)modeatvoltagesgreaterthan600V.
• Use Low Impedance (LOW Z) mode to reduce ghost voltages.
• Rotate selector to "AC" Voltage position.
• Attach RED lead to “V” input, BLACK lead to COM.
2. DCVoltage:<1000V.(LOWZ)<600V
Features:
MAX/MINRANGEHOLDREL
4. AC/DCCurrent(small):<400mA(For<400mAusemAµAinput)
Features:
 DONOTattempttomeasuremorethan400mA.
• Attach RED lead to “µA” input, BLACK lead to COM.
• Break circuit and connect meter in series (AS ABOVE).
• Select AC or DC current source.
5. Resistance/Diode/Continuity/Capacitance
Continuity Features:
MAX/MINHOLD
• Display shows resistance.
• Buzzer sounds if less than 40Ω.
Diode Features:
MAX/MINHOLD
Display shows:
• Forward voltage drop if forward biased.
• “O.L” if reverse biased.
AUTOHOLD
AUTOHOLD
AUTOHOLD MAX/MINRANGEHOLDREL
Resistance Features:
•
DONOT measure resistance on a live
circuit.
• Ω= < 50MΩ.
AUTOHOLDHOLDREL
RANGE MAX/MIN
 DONOTattempttomeasuremorethan10A.
• Start with this setting if current level is unknown.
• Break circuit to be measured.
• Attach RED lead to "A" input, BLACK lead to COM.
• Connect RED lead to one side of break and BLACK lead to the
other (meter in series).
• Meter will automatically select "A" when RED lead is connected to
"A" input. “LEAd” will show if connected but fuse is blown.
3. AC/DCCurrent(large):<10A
Features:
MAX/MINRANGEHOLDREL
 DONOTattempttomeasuremorethan1000V.
 DONOTuse(LOWZ)modeatvoltagesgreaterthan600V.
• Use Low Impedance (LOW Z) mode to reduce ghost voltages.
• Rotate selector to "DC" Voltage position.
• Attach RED lead to “V” input, BLACK lead to COM.
AUTOHOLD
A. DONOTattempttomeasuremorethan1000V.
B. DONOTattempttomeasuremorethan600Von(LOWZ)setting.
C. DONOTattempttomeasuremorethan400mA.
D. DONOTattempttomeasuremorethan10A.
E. AutoPower-Off(Apo)
• Device will power off after 30 minutes non-use.
• Press the select button to wake.
• Disabled during Max/Min function.
• Holding Select button while turning on disables Auto Power-Off.
F. SelectFunctionalityButton
• Switch between AC and DC.
• Switch between “Ω”, “ ”, “ ”, and “ ”.
• Switch between Hz and %.
• Switch between °F and °C.
• Wake meter during Auto Power Off.
G. RelativeReadingMode
• Press to store current value.
• Display shows the difference between the stored and live readings.
• Press again to return to live reading.
H. Auto/ManualRange
• Press repeatedly to cycle through manual ranges.
• Press for 2 seconds to return to auto ranging mode.
• AT is displayed on LCD only during auto ranging mode.
I. Max/MinHold
• Press to enter Max/Min mode; the largest and smallest values will be
saved while in this mode.
• Press repeatedly to alternate between the maximum and minimum
readings.
• Press for 2 seconds to return to live reading and clear the stored
maximum and minimum values.
J. Hold/AutoHold/Backlight
• Hold captures the current displayed value.
• Auto Hold captures the first stable displayed value, until a new stable
value is measured. The meter will then capture the new value and emit
a beep (V, Ohm, Temperature and Amp functions).
• Press to hold current input on the display.
• Press again to enter Auto-Hold to capture stable values.
• Press again to return to normal operation.
• Press and hold to activate display backlight.
• Using lights drains the battery significantly.
K.L. Battery/FuseReplacement
• When indicator is displayed on the LCD, batteries must be
replaced.
• Remove rubber boot, back screw and replace 2 x AAA batteries.
• This meter uses 440mA/1000V (69192) and 11A/1000V (69191)
fast blow fuses.
M. MagneticHangerAccessory(optional, sold separately)(69190)
• Slide magnetic adapter into protective rubber boot.
• Attach instruments to metal for hands-free use.
N. BarGraph
• The bar graph shows an approximate analog representation
of a measurement.
• The bar graph responds much faster than the digital display.
• The scale of the bar graph is zero to the maximum reading of
the selected range.
FUNCTIONINSTRUCTIONS
4007036