klover E-CONNECT 1700 User manual

E-CONNECT 1700
IT INSTRUCTIONS FOR USE
CS.ECN1700.IST-1 / Rev 1.0
Machine Translated by Google

Copyright © 2021 KLOVER
srl All rights reserved. It is forbidden to reproduce any part of this manual, in any form, without the explicit written permission of KLOVER srl. The
contents of this manual can be changed without notice. Every care has been taken in the collection and verification of the documentation contained
in this manual; however, KLOVER srl cannot assume any responsibility deriving from its use.
PUT IN ACTION............................................... .................................................. .................................................. ................................................ 18
CONFIGURATION OF THE SYSTEM ............................................... .................................................. .................................................. .............................. 18
FIRST FILLING OF THE SYSTEM .............. .................................................. .................................................. .................................................. ........ 20
PELLET LOADING AND CONNECTION TO THE ELECTRICITY NETWORK .................................. .................................................. .................................................. ........
20 IGNITION CYCLE ...................................... .................................................. .................................................. ............... ........................................ 20
SHUTDOWN CYCLE ...... .................................................. .................................................. .................................................. ................................... 21
MODIFICATION OF THE WORKING POWER AND THE BOILER WATER TEMPERATURES , BOILER OR PUFFER .................................................. ............................... 21
PROBLEMS, ALARMS, USEFUL ADVICE ............................................ .................................................. .................................................. .......... 22 YOU NEED TO
KNOW ... ................................. .................................................. .................................................. .................................................. ................. 22 WHAT
HAPPENS IF ... ............................ .................................................. .................................................. .................................................. ................ 22 ALARM
SIGNALS .............................. .................................................. .................................................. .................................................. 23
INSTALLATION SITE REQUIREMENTS ............................................. .................................................. .................................................. ............... 5
POSITIONING ................................. .................................................. .................................................. .................................................. .................. 5 SPACES
AROUND AND ABOVE THE APPLIANCE ........................ .................................................. .................................................. ....................................... 6
EXTERNAL AIR INTAKE ..... .................................................. .................................................. .................................................. ...................................... 6 FLUE
AND CONNECTION TO THE SAME ..... .................................................. .................................................. ................. .................................. 7
CHIMNEY .............. .................................................. .................................................. .................................................. ............................................. 8
CONDITIONS OF CONVENTIONAL WARRANTY .............................................. .................................................. .................................................. ........ 27
THE MACHINE AND THE PELLET ............................................. .................................................. .................................................. .......................................... 3
COMPONENTS OF THE APPLIANCE ... .................................................. .................................................. .................................................. ......................... 3
TECHNICAL CHARACTERISTICS ...................... .................................................. .................................................. .................................................. ............. 4
TECHNICAL SHEETS DIMENSIONS AND CONNECTIONS ............................... .................................................. .................................................. ...........................
4 CHARACTERISTICS OF THE PELLET ................... .................................................. .................................................. ................... ............................................. 5
WIRING DIAGRAMS AND PARAMETER TABLES ............................................. .................................................. .................................................. ........... 26
CS.ECN1700.IST-1 / Rev 1.0
HYDRAULIC CONNECTION ................................................ .................................................. .................................................. ................................ 10
ELECTRICAL CONNECTION ................................................ .................................................. .................................................. .................................. 9 CHECKING
ANY COMBINED BOILER ......... .................................................. .................................................. .............................................. 9 CONTROL OF A POSSIBLE
THREE-WAY MOTORIZED VALVE FOR DHW MANAGEMENT ......................................... .................................................. ........... 9 CONNECTION TO THE
ROOM THERMOSTAT .................................. .................................................. .................................................. ............................. 9
1
THE MENU................................................ .................................................. .................................................. .................................................. ................... 14
ITALIAN
THE DISPLAY................................................ .................................................. .................................................. .................................................. .............. 11
CLEANING AND MAINTENANCE ............................................... .................................................. .................................................. ..................................... 24
PRECAUTIONS TO BE TAKEN BEFORE CLEANING ...... .................................................. .................................................. ............................................. 24
ORDINARY CLEANING .. .................................................. .................................................. .................................................. .............................................. 24
EXTRAORDINARY CLEANING . .................................................. .................................................. .................................................. ....................................... 25
CLEANING THE CERAMIC GLASS ...... .................................................. .................................................. ....................... .................................................. .. 26
CLEANING THE CHIMNEY ........................................... .................................................. .................................................. ..................................... 26
MAINTENANCE ........... .................................................. .................................................. .................................................. ......................................... 26
INTRODUCTION................................................. .................................................. .................................................. .................................................. ....... 2
IMPORTANT SAFETY INSTRUCTIONS ...................................... .................................................. .................................................. .................................. 2
SUMMARY................................................. .................................................. .................................................. .................................................. .............. 1
SUMMARY
Machine Translated by Google

Klover declines all responsibility for accidents deriving from non-compliance with the specifications contained in this manual.
- Keep fuel and flammable materials at an adequate safety distance.
- The appliance is not suitable for installation on a shared flue system.
Important safety instructions
-
- The appliance can be used by children under the age of 8 and by people with reduced physical, sensory or mental abilities, or without experience or the
necessary knowledge, as long as they are supervised or after they have received instructions relating to the safe use of the appliance and an
understanding of the dangers inherent to it.
- NEVER open the appliance door during normal operation.
- If you are using a power strip, make sure that the total voltage of the connected devices does not exceed that supported by the socket. To check
- Do not touch the hot parts of the product (ceramic glass, smoke pipe and all the external frame) during normal operation.
- The appliance is an indoor product only and has the purpose of heating the water, so it must be connected to a system
- Connect the fumes outlet of the product to a flue having the characteristics shown in the section “Flue and connection to
- Do not use fuels other than those recommended; Do not use liquid fuels.
Extraordinary maintenance operations must only be carried out by authorized and qualified personnel.
- Authorize the use of the appliance to expert and competent persons.
- Keep children away from the appliance during normal operation as they could get burned by touching the hot parts of the appliance.
- Do not clean the appliance or its parts with easily flammable substances.
CS.ECN1700.IST-1 / Rev 1.0
-
- Prohibit the use of the appliance to children and the inexperienced; Children must not play with the appliance.
- The appliance works exclusively with wood pellets and exclusively with the firebox door closed.
- Do not use the power cord if it is damaged or frayed.
All safety standards required by the specific legislation in force in the state where it is installed must be respected.
- Do not make any unauthorized modifications to the appliance.
- Do not use the appliance as an incinerator or in any other way other than that for which it was designed.
All local regulations, including those referring to national and European standards, must be respected in the installation and use of the appliance.
- Do not use the appliance in disagreement with the instructions contained in this user manual.
- Carry out all maintenance operations constantly;
- The appliance's power cord plug must only be connected after the installation and assembly of the appliance has been completed and must remain
accessible after installation, if the appliance is not equipped with a suitable and accessible bipolar switch.
- During the ignition phase and normal operation of the appliance it is advisable to keep the necessary safety distances and not to stand
- Do not leave the packaging elements within reach of children or unassisted disabled people.
- Do not leave containers and flammable substances in the room where the appliance is installed.
ITALIAN
Failure to comply with the instructions contained in this manual automatically invalidates the guarantee.
The responsibility for the works carried out for the installation of the product is not borne by Klover, but is entirely borne by the installer who is
also responsible for carrying out the checks relating to the flue and the external air intake and the correctness of the proposed installation
solutions.
- Connect the product to grounded electrical outlets. Avoid using electrical outlets controlled by switches or automatic timers.
and the associated responsibility of the manufacturer.
- The installation and commissioning of the appliance must be carried out by competent personnel aware of compliance with the safety standards in force,
who will assume full responsibility for the final installation and consequent good operation. There will be no liability on the part of Klover srl in case of
failure to comply with these precautions.
-
- Cleaning and maintenance intended to be carried out by the user must not be carried out by unsupervised children.
- Switch off the electrical panel using the appropriate button. Do not unplug the power cord while the appliance is running.
also that the total voltage of all devices connected to the wall socket does not exceed the maximum allowed level.
Use the appliance within the limits of its use;
sunburn.
itself ”of this User Guide.
This user manual is an integral part of the appliance. If the product is sold, the user is obliged to deliver this manual to the new purchaser as well.
Furthermore, Klover declines any responsibility deriving from improper use of the product by the user, from unauthorized modifications and /
or repairs, from the use of non-original or non-specific spare parts for this product model.
Use only original spare parts recommended by the manufacturer.
In the event of a fire in the flue, use suitable systems to suffocate the flames or request the intervention of the fire brigade.
Read these instructions before installing and using the product.
2
in front of the same.
- Do not touch the appliance if you are barefoot and / or with wet or damp parts of the body.
-
- The use of poor quality pellets or any other material damages the functions of the appliance and can lead to the termination of the guarantee
For the warranty to be valid, the user must observe the provisions contained in this manual and in particular:
hydraulic (radiators, puffers, etc.) that is suitably designed and sized to dispose of the power developed.
- The appliance, especially the external surfaces, when in operation reaches high temperatures to the touch; maneuver carefully to avoid
-
INTRODUCTION
Machine Translated by Google

Optional
Safety valve drain.
TA terminal for
room thermostat
connection.
Delivery pipe.
Suction tube.
Pressure gauge 0 - 4 bar
Nr. 1 power cable
Interference filter.
Serial connection
The images below show some details of the appliance:
Automatic air vent valve
CS.ECN1700.IST-1 / Rev 1.0
Yup
Manual reset safety
thermostat .
Yes. Mod. 25/70
ITALIAN
Components of the appliance
Heating system pump
-
CE label with
technical data, serial number
and model.
3
for possible connection of
boiler / puffer probe.
Optional
8 lt
Expansion vessel
In addition, the device is delivered with the following material:
Remote control
Nr. 1 use, installation and maintenance manual;
Safety valve 2.5 bar
-
Smoke exhaust.
Main switch, connection for
power cable and 2 built-in
fuses (4A 250V).
for WiFi module connection
and / or for Service Center
connection.
NoNon-return valve
Nr. 1 conventional guarantee certificate.
Return pipe.
-
Electric predisposition for boiler / puffer probe
WiFi management module
Yup
The table below shows the standard features of the appliance:
Clamp
THE MACHINE AND THE PELLET
Machine Translated by Google

16.4
Watt
230
25
kcal / h
CO measured at 13% oxygen at nominal heat output
ITALIAN
Nominal heat output
92.1
Minimum chimney draft at nominal heat output
Power absorbed only during the ignition cycle.
10
° C
kcal / h
%
Smoke outlet pipe diameter
Maximum electrical absorption
Ventilated pellet tank capacity (ducted)
g /
sg /
s
kg ° C
4.2
3,600
mm
kW
Efficiency at reduced thermal power
0.013
Mass of combustion gases with reduced thermal power
All the technical data sheets of dimensions and connections are visible by scanning the following QR Code from your smartphone:
*
kcal / h
Watt
40
9.7
kW
%
Nominal frequency
Minimum safety distance from flammable materials (side / rear / front)
15.1
12.980
mm
50
200
Efficiency at nominal heat output
0.003
Mass of combustion gases at nominal heat output
Dimensions and connections data sheets
4.5
3,870
kW
%
400 *
9.6
Average flue gas temperature at reduced heat output
CS.ECN1700.IST-1 / Rev 1.0
Reduced heat output
Pa
Air intake pipe diameter
Hz
80
60
kcal / h
%
Nominal tension
14.100
V.
50
100
Technical features
Reduced heat output
93.5
Minimum draft to the chimney at reduced heat output
The heat output produced by the appliance may vary according to the type of pellet used.
Nominal heat output
Pa
10
mm
kW
CO measured at 13% oxygen at reduced heat output
Electric absorption in operation
Average flue gas temperature at nominal heat output
4
https://docs.klover.it/it/guide/help/cs-ecn1700-tds-1
E-CONNECT 1700
Machine Translated by Google

INSTALLATION SITE REQUIREMENTS
- Code of the country of manufacture
(example "IT")
Possibility of creating an external air intake;
Appropriate measures must be taken (eg load distribution plate).
Possibility of creating a straight flue and possibly coaxial to the appliance's smoke outlet;
- Proximity or ease of connection to the hydraulic network;
- 100% wood. Total absence of additives.
- The packages are intact as the pellet tends to absorb moisture. Humidity not only reduces the calorific value and increases the fumes emitted but swells the
product which could create problems for the appliance.
The use of poor quality pellets or any other material damages the functions of the appliance and can lead to the termination of the guarantee and the
associated liability of the manufacturer.
The minimum safety distance from flammable materials must be at least 200 mm from the sides, 200 mm from the back, 800 from the front and 750 mm
from the top of the appliance.
Once the best arrangement has been established, proceed with positioning the appliance by carefully following the indications given below.
To ensure trouble-free combustion, the pellets must be stored in a dry place.
It is advisable to use good quality pellets to have a good efficiency of the appliance. The pellets must be poured into the tank with a shovel and not directly
from the bag.
CS.ECN1700.IST-1 / Rev 1.0
Indication of the standard,
basic reference for the ENplus
quality classes
-
Indication of the quality
class of the certified pellet
To recognize quality pellets, it is necessary that:
The appliance has been tested with all types of pellets on the market. The pellets used must have the following characteristics:
ITALIAN
-
5
The appliance must be installed on a floor with adequate load capacity. If the existing construction does not meet this requirement,
Certified company code
consisting of two elements:
- The details of quality certifications and in particular compliance with international standards such as EN14961-2, DIN are indicated on the packaging
- Maximum length 35 mm.
- Progressive number assigned
- There is not a lot of powdered wood inside the packages;
upon the acquisition of certification
(example "xxx")
- Maximum moisture content 8 - 9%.
51731 and O-NORM M7135;
The initial phase for the best installation of the appliance is to identify its optimal location; in this regard, the following elements should be considered:
- Proximity to the main hydraulic manifold and / or to the boiler (if one already exists);
The installation must guarantee easy access for cleaning the appliance, the flue gas ducts and the flue and any subsequent maintenance by the Authorized
Technical Assistance Center.
It is forbidden to install the appliance in small rooms, bedrooms, bathrooms and in environments with an explosive atmosphere (e.g. garages).
For the production of pellets, international standards must be respected (for example EN14961-2, DIN 51731 and O-NORM M7135) which establish minimum
values to verify the quality of the pellets. To facilitate the right choice of fuel, we list below one of the most common certification marks that identify the quality of the
pellets:
- Maximum ash residue 1.1%.
Easy access for cleaning the appliance, the flue gas pipes and the flue.
Positioning
Characteristics of the pellets
- Taking a handful of pellets and pouring it into a bowl full of water, the quality pellets will sink, if not, they will tend to float;
- It is built from cylinders of constant diameter and has a smooth and shiny surface;
(A1 preferable)
- Diameter 6 mm.
-
IT xxx
Machine Translated by Google

If there are other heating or suction appliances in the room, the air intakes must guarantee the necessary volume of air for the correct operation of all devices.
Protect all structures that could catch fire from hot radiation from the fire.
In the room where the pellet appliance is installed, only appliances operating in a sealed manner with respect to the room may pre-exist or be installed (e.g. type C
gas appliances, as defined by UNI 7129) or which in any case do not depress the room with respect to the external environment.
Any extra intervention by the Authorized Technical Assistance Center, in which it is necessary to disconnect the appliance from the system, will not be
recognized under the warranty as indicated in the chapter “Conventional Warranty Conditions”.
Extraction fans can cause the appliance to malfunction if used in the same room.
External air intake
6
CS.ECN1700.IST-1 / Rev 1.0
During the functioning of the appliance, combustion air is taken from the environment in which it is installed; it is therefore essential that this air is reintegrated
through an external air intake. Failure to make the air intake affects the draft in the flue and therefore the combustion and safety of the appliance.
ITALIAN
It is therefore mandatory to create an external air intake that has a minimum completely free passage of at least 80 cm2 (round hole with a minimum diameter
of 15 cm protected with a special fixed grid with large meshes).
Spaces around and above the appliance
If it is not possible to make the external air intake in the same room where it is installed, this hole can be made in another adjacent room as long as it is permanently
communicating with a transit hole (minimum diameter 15 cm).
The figure below shows the minimum measurements to be respected when positioning the appliance with respect to walls or furniture that is not easily removable.
The hole must be protected externally with a fixed grid. The protection grid must be checked periodically to verify that it is not obstructed, thus preventing the
passage of air. Therefore, keep the air intakes free from obstructions.
Any shelves or false ceilings mounted above the appliance must be spaced at least 75 cm from the top of the appliance.
The UNI 10683 standard PROHIBITS the withdrawal of combustion air from garages, from warehouses of combustible material or from activities with a fire hazard.
Cabinets and movable objects made of flammable material must be positioned at least 20 cm from the side walls of the appliance; these objects must be moved in
case of maintenance of the same.
Machine Translated by Google

-
The pipes must be double-walled (insulated) or adequately insulated with rock wool. The maximum temperature of the pipe
-
smoke inside the room must not exceed 70 ° C.
-
any condensation;
- It is forbidden to use fiber cement pipes to connect the appliances to the flue;
-
7
ADDITIONAL SPECIFICATIONS TO CONSIDER
- Have a preferably circular internal section: square or rectangular sections must have rounded corners with a radius of not less than
CS.ECN1700.IST-1 / Rev 1.0
The assembly of the smoke channels must be carried out in such a way as to guarantee the seal against fumes for the operating conditions of the appliance in
depression;
-
- The assembly of horizontal sections is prohibited;
ITALIAN
20 mm;
The flue is a fundamental element for the good functioning of the appliance. The minimum section of the flue must be that indicated in the technical characteristics
of the appliance (SL140 80 mm, SL180 / SL220 100 mm). Each product must have its own flue, with no other inputs (boilers, fireplaces, stoves, etc…). The
dimensions of the flue are closely related to its height, to be measured from the mouth of the appliance to the base of the chimney pot. To guarantee draft, the
smoke outlet surface of the chimney pot must be double the section of the flue. The combustion products evacuation duct generated by the forced draft appliance
must meet the following requirements:
- The appliance works with the combustion chamber in depression and the smoke pipe under pressure; it is essential that the fume exhaust is airtight
- Any change of direction must be made with a T-fitting with inspection cap. The pipes must guarantee smoke tightness via
IT IS STRICTLY FORBIDDEN TO INSTALL DRAFT REGULATION VALVES (BUTTERFLY VALVES).
- Have rectangular sections with a maximum ratio between the sides of 1.5;
- For the assembly of the smoke ducts (section that goes from the appliance to the entrance to the flue), elements of
The smoke channel must allow the recovery of the soot or be brushless and must have a constant section;
-
UNI 9615);
- It is forbidden to allow other air supply channels and pipes to be used inside the smoke ducts, even if they are oversized.
- Be made of materials suitable to withstand normal mechanical stress, heat, the action of combustion products and
non-combustible materials suitable for resisting combustion products and their possible condensation (the use of aluminum flue pipes is absolutely
forbidden);
The smoke pipes inside the installation room must be made of suitable material (see current regulations) and equipped with sealing gaskets, with a
minimum diameter of 80 mm.
IT IS COMPULSORY TO MAKE A FIRST VERTICAL SECTION OF AT LEAST 0.5 MT TO GUARANTEE THE CORRECT EXPULSION OF FUMES.
The smoke channels must not cross rooms where the installation of combustion appliances is prohibited;
- Having, after the vertical section, for the entire remaining route, an upward trend, with a minimum gradient of 5%. The sub-horizontal part must not have a
length greater than ¼ of the effective height H of the chimney or flue, and in any case it must not have a length greater than 2,000 mm;
plant engineering.
-
hermetic.
Chimney and connection to it
- Have a constant, free and independent internal section;
- The use of counter-slope elements is prohibited;
- Be insulated to avoid the cooling of the fumes and the formation of condensation;
- Be sealed against combustion products, impermeable and adequately insulated and insulated according to the conditions of use (cf.
special seals resistant to 250 ° C. Fix the pipes to the wall with special collars to avoid any vibrations.
Machine Translated by Google

theridge
15 °
0.5mover
1mminimum
Distance> 5 m Distance <5 m
Volume
technician
0.5m 0.5m
Distance> 1.85 m
Distance <1.85 m
Reflux
area
Chimney
If the flue is old or too large (internal diameter greater than 15 cm), pipe the flue with a suitably insulated stainless steel pipe (using rock wool or vermiculite)
and sized according to the route. The connection to the flue must be properly sealed.
- Have a useful outlet section no less than double that of the flue on which it is inserted;
When making the flue, no more than 4 changes of direction must be made.
ITALIAN
The outlet height (where by height is meant that which corresponds to the top of the flue, regardless of any chimney pots) must be outside the so-called reflux
area, in order to avoid the formation of back pressures, which prevent free discharge in the atmosphere of the products of combustion.
It must meet the following requirements:
It is therefore necessary that the minimum heights indicated in the following figures are respected:
CS.ECN1700.IST-1 / Rev 1.0
- Be constructed in such a way that, even in the event of winds of any direction and inclination, combustion exhaust is still ensured.
The chimney pot is a device placed on top of the flue to facilitate the dispersion of the combustion products.
8
- Be shaped in such a way as to prevent rain and snow from entering the flue;
Machine Translated by Google

CN16
-
- The appliance switches off with a delay set on Pr44.
-
When constructing the system, bear in mind that the cables must be laid immovably and away from parts subject to high temperatures.
The pellet appliance is equipped with a control for a possible three-way motorized valve to be installed on the DHW circuit according to the type of
system chosen (see “System configuration”). In the right inside of the appliance there are four wires with faston protected by a red sheath, which can
be used to control this valve (see also “Wiring diagram”). The four threads are of different color and precisely:
Connection to the room thermostat
The OPEN CONTACT operating principle is listed below :
KLOVER srl declines all responsibility for damage to persons, animals or things deriving from failure to connect the appliance to the earth
network and from non-compliance with CEI standards.
CS.ECN1700.IST-1 / Rev 1.0
Black wire = SANITARY SIDE (230 V phase when DHW on request)
Brown wire = HEATING SIDE (Phase 230 V when DHW is not in demand)
ITALIAN
Control of any combined boiler
- The appliance goes directly into "T-AMB ECONOMY" operating economy
The electrical connection must be carried out exclusively by qualified personnel, in compliance with all general and local safety regulations in force.
The two wires arranged on the left technical compartment of the appliance (blue wire and brown wire), at the output will have a voltage of
230 V when the pellet appliance circulator operates, no voltage when the circulator stops.
-
-
The safety of the appliance is obtained when it is correctly connected to an effective grounding system.
The appliance's heating circulator switches off.
-
Provide, in the electrical connection to the power supply network, a differential magnetothermic switch at 6 A - Id 30 mA with suitable breaking load.
The electrical connections, including earthing, must be made after removing the voltage from the electrical system.
Control of a possible three-way motorized valve for DHW management
9
Blue wire = COMMON 3-WAY VALVE (Neutral 230 V)
In the final wiring of the circuit, use only components with an adequate degree of electrical protection. Take care not to run electric cables in the
immediate vicinity of the flue pipe unless they are insulated with suitable materials.
Behind the appliance there is a jumpered terminal which is used to connect any room thermostat that will control its operation. The operation of the
room thermostat is enabled with type of system 1, 2 and 3 (see “System configuration”).
- thus reducing the working power to a minimum.
If you want to combine the pellet appliance with another boiler already installed on the system (e.g. wall-mounted gas boiler), make sure that when the
latter works for system heating, the combined boiler stops. The electrical predisposition, accessible from the right inside of the appliance, intervenes
on the combined boiler when the pellet appliance heating circulator starts, so as to avoid having two boilers operating at the same time on the same
system. However, the combined boiler will always be usable for the production of domestic hot water.
Yellow / green wire = GROUND
Check that the power supply voltage and frequency correspond to 230V - 50 Hz.
It is therefore necessary to connect the 2 wires to a relay that will control the Room Thermostat (TA) input of the combined boiler (see example below).
ELECTRICAL CONNECTION
Machine Translated by Google

When installing the appliance it is recommended to insert an anti-condensation mixing valve between the flow and return of the heating
system of the appliance itself. The anti-condensation valve must be calibrated at 55 ° C and with a Kv value equal to or greater than 8 m3 / h.
NB: If the water temperature exceeds the threshold of 80 ° C (safety temperature), the system circulator is forced to switch on to ensure the disposal of
excessive heat, thus avoiding the achievement of high temperatures of the water in the boiler. For this reason it is advisable that the heating system is
not completely closed.
When connecting the appliance to the system, it is advisable to provide an area that is always open (e.g. bathroom area) to ensure the
dissipation of excess heat from the water in the boiler body.
In the “System type 3” configuration, the appliance goes into economy with subsequent shutdown only if the temperature set in the “SET BOILER” has
also been satisfied.
The maximum inlet pressure of the mains water must never exceed 2.5 bar; the recommended operating pressure is 1.5 bar
ATTENTION: If the room probe in the “Remote control” is also enabled, the appliance goes into economy if the temperature set in the “ROOM SET” has
also been satisfied.
(with appliance running).
CS.ECN1700.IST-1 / Rev 1.0
In the case of water with a hardness higher than 28 ° f, it is essential to install an anti-limescale device, to be chosen based on the
characteristics of the water.
The hydraulic connections must be made rationally using the connections on the template of the appliance.
ITALIAN
IN ORDER NOT TO COMPROMISE THE OPERATION AND LIFE OF THE HEATING CIRCULATOR, IT IS RECOMMENDED TO INSTALL A
MAGNETIC FILTER AND SEALER DOWNSTREAM OF THE APPLIANCE RETURN HOSE.
The automatic restart of the appliance occurs if all the following conditions exist:
The appliance can be combined with any other boiler already installed in the system; naturally it is essential to insert the necessary safety devices and
interceptions depending on the system and use. It is also necessary to take into consideration all the national, regional, provincial and municipal laws
and regulations present in the country where the appliance is installed.
The assembly of the appliance must only be carried out by qualified personnel. Scrupulously observe the contents of this booklet.
- If the contact of the room thermostat closes.
The appliance can be installed with the expansion vessel closed as it is equipped with a fuel load stop device, a thermostat with manual safety reset
and an acoustic alarm which intervene in the event of excessively high temperatures.
We decline all responsibility for damage caused by incorrect assembly.
- If it goes below the temperature differential (SET H2O - Pr43).
The appliance can be installed in the same room as another boiler only if this is a sealed chamber; the installation must be carried out in
compliance with the regulations in force.
10
- After a possible cooling cycle.
HYDRAULIC CONNECTION
Machine Translated by Google

EFFECTIVE WORKING POWER
MENU LEVEL
CLOCK
(Displayed flashing only when different from the
one actually set)
The INPUT area displays the entered programming values.
WATER TEMPERATURE
The figure below shows the display in the programming or operating parameters setting phase.
The MENU LEVEL area displays the current Menu / Parameter level.
17:19
INPUT
The DIALOG area displays the meaning of the current Menu / Parameter.
CS.ECN1700.IST-1 / Rev 1.0
60 ° C
Hon
11
ITALIAN
WORK 3
M - 2 - 2 - 01
- - - -
CHRONO
The console displays information on the operating status of the device. By accessing the menu it is possible to obtain various types of display and make the
available settings according to the selected menu.
2
DAY
DIALOGUE
The figure below shows the display when the device is switched on.
DIALOGUE
AMBIENT TEMPERATURE (optional)
THE DISPLAY
Machine Translated by Google

On the menu ..
(3) The first press allows you to select:
In work / off ..
Pressed for 2 seconds turns the appliance on and / or off.
REFERENCE
"Centralized puffer temperature set - PUFFER SET" (System type 4)
Access the selected menu.
Move to the next menu item.
1
4
(3)
In programming ..
On the menu ..
Go to the next submenu item and save the changes made.
(2) The first press allows you to select:
On the menu ..
(1) The first press allows you to select:
CS.ECN1700.IST-1 / Rev 1.0
(2)
"DHW boiler temperature set - BOILER SET" (System type 3)
The table describes the operation of the keys on the display.
Decreases the temperature value of the water / room
thermostat.
Decreases the working / ventilation power of the appliance.
(1)
12
Outlet
Increase power
OPERATION
Set
5
-
Decrease temperature
In work / off ..
In programming ..
It moves to the previous menu level, saving the changes
made.
"Boiler water temperature set - SET H2O" (System type 1, 2)
ITALIAN
2
-
Increase temperature
ON / OFF
METHOD
3
Go to the previous menu item.
(3)
-
Modify / decrease the selected menu value.
In menu / programming ..
Go to the previous submenu item and save the changes made.
In work ..
In work / off ..
-
In programming ..
Increases the working / ventilation power of the appliance.
“Working power set - POWER SET”.
Modify / increase the selected menu value.
Unlock the alarm.
KEY DESCRIPTION
-
Decrease power
Increases the temperature value of the water / room
thermostat.
In alarm block ..
-
6
Enters the next submenu level.
In programming ..
In work / off ..
"Boiler water temperature set - SET H2O" (System type 1, 2, 3)
Machine Translated by Google

Not used
Weekly Chrono
Call Acs
Winter mode
19
15
8
LED DESCRIPTION
12
Lit when the Week-End Chrono Programming is active.
On with Pellet Loading Gear Motor powered.
18
21
Menu 01-CHOOSE SEASON = SUMMER
On in alarm conditions.
On with room thermostat contact input open (satisfied).
CS.ECN1700.IST-1 / Rev 1.0
Menu 01-CHOOSE SEASON = WINTER
14
Ignition Plug Ignited with Ignition Plug powered.
REFERENCE
Not used
or with T.BOILER (System Type 3) / T.PUFFER (System Type 4) on call.
Pellet loading
Lit when Weekly Chrono Programming is active.
On when the DHW only mode (Summer) is activated.
Room thermostat
On with System Circulator powered.
Summer mode
13
Chrono Programming On with at least one Chrono Programming active.
ITALIAN
On when the Heating + Domestic hot water mode (Winter) is activated.
13
Week-End Chrono
The table describes the meaning of the LEDs on the display.
10
On with closed DHW flow switch contact input (DHW on request)
20
Lit when Chrono Day programming is active.
Active alarm
7
On when cleaning turbulators running.
22
Fume extractor
16
17
On with powered fume extractor.
Not used
Turbulator cleaner
9
Chrono Day
OPERATION
System circulator
Flashing as much as turbulator cleaning reserved at the next start-up.
Not used
11
11
7
15 16 17 18
12
10 19 20 21 22
14
9
13
8
Machine Translated by Google

POSSIBLE VALUES
Switch-on time of the second program
Allows you to enable, disable and set the daily chronothermostat functions.
ÿ SUMMER = DHW only operation = Summer mode.
Press key 3 (Set) to access the Menu. This is divided into various items and levels that allow access to the settings and programming of the appliance.
The weekly programmer has 4 independent on / off programs; it is not essential to use them all at the same time.
M03-3-01
STOP 1 DAY
SELECTION
Menu M03 - CHRONO SET
M03-2-02 Enable / disable the daily schedule
Menu M01 - SYSTEM MODE
MEANING
Now - OFF
Enable / disable the weekly program
- Sub-menu M03-3 - WEEKLY PROGRAM
SELECTION
when at least one on / off program is enabled (daily program, weekly program or weekend program).
CS.ECN1700.IST-1 / Rev 1.0
MENU LEVEL
START 1 DAY
M03-1-01
Allows you to set the current time and date.
ON - OFF
M03-2-01
ON - OFF
The list of menus available is listed below.
MEANING
Now - OFF
It allows you to globally enable and disable all the chronothermostat functions. For correct operation it is advisable to enable it ("ON")
M03-2-05
MEANING
CHRONO DAY
MENU LEVEL
ITALIAN
Allows you to enable, disable and set the weekly chronothermostat functions.
14
POSSIBLE VALUES
Menu M02 - CLOCK SET
POSSIBLE VALUES
Use keys 1 and 2 to modify the value set in the selected menu.
MENU LEVEL
WEEK CHRONO
STOP 2 DAY
M03-2-04
- Sub-menu M03-1 - ENABLE CHRONO
Now - OFF
ON - OFF
- Sub-menu M03-2 - DAILY PROGRAM
Allows you to set how to use the appliance:
Time to switch off the first program
Time to switch off the second program
It is possible to set two operating bands delimited by the times set according to the following table where the OFF setting instructs the clock to ignore the
command:
ÿ WINTER = Heating + DHW operation = Winter mode.
Use keys 5 and 6 to select the menu to be modified.
By setting OFF in the time field, the clock ignores the corresponding command.
SELECTION
ENABLE CHRONO
START 2 DAY
Allows you to set any scheduled operating times.
M03-2-03 Now - OFF
Start-up time of the first program
Enable / disable the set programs
It can only be used with System Type 3 (see paragraph “System configuration”).
THE MENU
Machine Translated by Google

M03-3-26
On / off
WEDNESDAY PROG 4
M03-3-37
M03-3-04
MEANING
On / off
Allows you to enable, disable and set the weekend chronothermostat functions (Saturday and Sunday).
Now - OFF
SATURDAY PROG 3
M03-3-30
SELECTION ON - OFF
MONDAY PROG 2
M03-3-17
Time to switch off the third program
On / off
Time to switch off the first program
THURSDAY PROG 1
MENU LEVEL MEANING
On / off
SELECTION
M03-3-05
On / off
STOP 2 WEEK-END
POSSIBLE VALUES
FRIDAY PROG 1
M03-3-31
CS.ECN1700.IST-1 / Rev 1.0
On / off
WEEK-END CHRONO
THURSDAY PROG 4
POSSIBLE VALUES
Reference days of the third program
On / off
START PROG 3
M03-3-24
M03-3-11 Switch-on time of the second program
On / off
TUESDAY PROG 2
M03-3-18
On / off
THURSDAY PROG 3
MENU LEVEL
M03-4-04
On / off
Switch-on time of the third program
Now - OFF
Now - OFF
SUNDAY PROG 2
M03-3-22
Reference days of the fourth program
MEANING
TUESDAY PROG 1
M03-3-09
Reference days of the first program
On / off
MONDAY PROG 4
M03-3-35
M03-3-02
Start-up time of the first program
On / off
M03-3-29
M03-4-05
Now - OFF
On / off
TUESDAY PROG 4
M03-3-36
SELECTION
M03-3-23
- Sub-menu M03-4 - WEEK-END PROGRAM
POSSIBLE VALUES
FRIDAY PROG 3
PROGRAM 2
On / off
STOP PROG 2
M03-3-16
M03-3-03
On / off
Enable / disable the weekend program
Start-up time of the first program
WEDNESDAY PROG 1
M03-3-10
POSSIBLE VALUES
FRIDAY PROG 2
M03-3-20
Switch-on time of the fourth program
On / off
On / off
SELECTION
M03-3-14
PROGRAM 3
START PROG 4
M03-3-33
PROGRAM 1
STOP 1 WEEK-END
Now - OFF
Switch-on time of the second program
SATURDAY PROG 4
On / off
TUESDAY PROG 3
M03-3-27
M03-4-02
On / off
Now - OFF
M03-3-21
Time of shutdown of the fourth program
On / off
WEDNESDAY PROG 3
M03-3-28
START PROG 2
M03-3-15
MEANING
Now - OFF
SATURDAY PROG 2
MENU LEVEL
START 2 WEEK-END
Now - OFF
SUNDAY PROG 4
Time to switch off the first program
MONDAY PROG 1
M03-3-08
M03-4-03 Now - OFF
On / off
STOP PROG 4
M03-3-34
On / off
Now - OFF
SATURDAY PROG 1
M03-3-12 Time to switch off the second program
Time to switch off the second program
POSSIBLE VALUES
FRIDAY PROG 4
START PROG 1
M03-3-06
STOP PROG 3
M03-3-25
MENU LEVEL
Now - OFF
SUNDAY PROG 3
On / off
WEDNESDAY PROG 2
M03-3-19
PROGRAM 4
On / off
M03-3-13
Reference days of the second program
On / off
THURSDAY PROG 2
STOP PROG 1
M03-3-07
On / off
Now - OFF
SUNDAY PROG 1
M03-4-01
15
On / off
SELECTION
M03-3-32
ITALIAN
MENU LEVEL
START 1 WEEK-END
MEANING
On / off
MONDAY PROG 3
Machine Translated by Google

Allows you to set how to manage the activation of the Vacuum:
16
Menu M05 - ACOUSTIC ALARM
Menu M09 - SYSTEM TYPE
ÿ TIME = activation with established time (possibility to switch it on at one or two times a day)
- Sub-menu M10-2 - TIME 1
Menu M06 - INITIAL LOAD
CS.ECN1700.IST-1 / Rev 1.0
The menu is reserved for expert users only; access by non-expert users can cause serious damage to the equipment, people, property and the environment. Klover
declines any responsibility deriving from an improper calibration of these values.
Menu M10 - VACUUM MANAGEMENT
ITALIAN
It allows to carry out, with the appliance off and cold, a pellet pre-charge for a time equal to 180 ”. Start with key 1 and stop with key 4. It can be useful if the appliance is
switched on after the tank has been completely emptied or is the first time it is filled.
Deactivate the Daily Chrono if you want to use the Weekly one. Always keep the Week-End Chrono disabled if you use the Weekly Chrono in programs 1, 2, 3
and 4.
With M10-1 - MANAGEMENT TYPE = TIME, it allows you to set the first daily vacuum activation time.
Menu M07 - STOVE STATUS
Menu M08 - TECHNICIAN SETTINGS
ÿ SENS = activation with pellet reserve sensor.
- Sub-menu M10-1 - MANAGEMENT TYPE
Menu M04 - CHOOSE LANGUAGE
Whenever the pellets in the primary tank go below the minimum sensor, the Vacuum is activated, regardless of the time.
Allows you to select the dialogue language from those available (Italian, English, French, German and Spanish).
It allows you to access everything reserved for the Technical Assistance Center. Access is protected by an access key. Unauthorized access can cause serious damage
to the equipment, people, property and the environment.
With M10-1 - MANAGEMENT TYPE = TIME, it allows you to set the second daily vacuum activation time.
It allows you to configure the appliance according to the type of system to which it has been connected (see “System configuration”).
Allows you to enable or disable the acoustic signal in the event of an alarm. The acoustic signal is present only on the board on the machine and not on the external
“remote control” .
Each time the clock detects the set time, the Vacuum is activated.
- Sub-menu M10-3 - TIME 2
TIP: in order to avoid unwanted switching on and off operations, activate only one program at a time (Daily, Weekly or Week-End Chrono).
Attention: when the operation is completed, before switching on the appliance it is advisable to empty the accumulation of pellets deposited inside the brazier.
Allows you to enable the pellet reserve sensor in the tank and to configure the operation of any automatic loading system with auxiliary tank.
Activate the Week-End Chrono only after having deactivated the Weekly Chrono.
Allows you to view the instantaneous status of the appliance by reporting the status of the various devices connected to it. There are several pages displayed in
succession. The data shown is reserved for the Technical Assistance Center.
Machine Translated by Google

Allows you to set how to manage the activation of the smoke pass cleaner:
With Submenu M12-1 - MANAGEMENT TYPE = TIME, it allows you to set the daily end time of the band within which automatic cleaning is allowed.
ÿ ON = cleaner always active.
17
MENU
Allows you to perform a limited calibration of the pellet load (PELLET TYPE) in the manner indicated in the table below:
*
ÿ TIME = cleaner active with established time band.
liability deriving from improper calibration of these values.
TIME OFF TURB), the automatic cleaning of the smoke circuit is carried out. If ignition always occurs outside the set time band, automatic
cleaning is performed at the first available ignition after the time set in Pr144 has elapsed.
CS.ECN1700.IST-1 / Rev 1.0
VALUES THAT CAN BE SET
MEANING
- Sub-menu M12-2 - TIME ON TURB
ITALIAN
By increasing the value of a single unit, the speed of the fume extractor (and therefore the intake
of combustion air) is increased by approximately 3%.
By increasing the value of a single unit, the pellet load is increased by about 2%.
Menu dedicated to expert users only; it allows to carry out a limited calibration of the pellet load (PELLET LOAD) and the speed of the fume extractor
Menu M12 - CLEANING MANAGEMENT
GUY
VALUES THAT CAN BE SET
- TYPE OF FIREPLACE
-4 / +4
PELLET
- Sub-menu M12-1 - MANAGEMENT TYPE
Allows you to perform a limited calibration of the speed of the fume extractor (CHIMNEY TYPE) in the manner indicated in the table below:
- PELLET TYPE
-4 / +4
Each time the appliance is switched on, the automatic cleaning of the smoke pass is carried out, regardless of the time.
- Sub-menu M12-3 - OFF TURB TIME
MENU
Access by non-expert users can cause serious damage to the equipment, people, things and the environment. Klover declines every
Each time the appliance is switched on within the set time band (see Submenu M12-2 - TIME ON TURB / M12-3 -
MEANING
Menu M11 - USER SETTINGS
By decreasing the value of a single unit, the speed of the fume extractor (and therefore the
intake of combustion air) is reduced by about 3%.
By decreasing the value of a single unit, the pellet load is reduced by about 2%.
(ASP-FUMI CAMINO) in the manner indicated in the table below:
FIREPLACE
Allows you to configure the operation of the automatic flue gas cleaner.
With Submenu M12-1 - MANAGEMENT TYPE = TIME, it allows you to set the daily start time of the band within which automatic cleaning is allowed.
GUY
Machine Translated by Google

Before putting the appliance into operation, it is advisable to choose the type of system to which it has been connected, by accessing the “M09 - SYSTEM
TYPE” menu.
ÿ 2 = Boiler with integrated instantaneous DHW, connected to a heating system combined with an alternative DHW generator.
The SYSTEM TYPE configurations available are shown below:
CS.ECN1700.IST-1 / Rev 1.0
System Type “2” provides for the connection of the boiler with integrated instantaneous DHW (pre-set model) to the heating system managed with one or
more room thermostats, connected to the terminal set up inside the technical compartment of the appliance. The production of DHW is obtained by means
of a mini-accumulation integrated in the appliance. To always guarantee DHW, in this system configuration it is necessary to combine an alternative DHW
generator. The combination with the alternative DHW generator is managed by means of a three-way motorized valve connected to the pellet appliance: in
this way, the DHW produced by the pellet appliance can be used only when the latter is in operation and therefore at temperature.
ÿ 1 = Boiler connected to a heating system and possible external plate exchanger for the production of DHW.
ITALIAN
18
The System Type "1" provides for the connection of the boiler to the heating system (also centralized puffer) managed with one or more room thermostats,
connected to the terminal inside the technical compartment of the appliance. The possible production of DHW is obtained by means of a plate exchanger
mounted externally to the appliance and managed with a flow switch, also connected to a terminal predisposed in the boiler, which will have the function of
immediately bringing the appliance to domestic power and thus switching a three-way motorized valve to give priority.
System configuration
PUT IN ACTION
Machine Translated by Google

ITALIAN
With “Menu 01 - CHOOSE SEASON = SUMMER” only the storage tank is managed in the summer period, keeping the heating system off.
CS.ECN1700.IST-1 / Rev 1.0
The three-way motorized valve, controlled by the pellet appliance, allows you to manage the heating of the system or the boiler, giving the latter priority.
19
The System Type "3" provides for the connection of the boiler to the heating system managed with one or more room thermostats, connected to the
terminal inside the technical compartment of the appliance. DHW production is obtained by means of a storage tank mounted externally to the
appliance and managed with a temperature probe connected to it.
The System Type "4" provides for the connection of the boiler to a centralized puffer managed with a temperature probe connected to the terminal
inside the technical compartment of the appliance. The appliance works with only the centralized puffer temperature (“SET PUFFER” which can be set
with keys 1 and 2). This system configuration does not require any connection to the appliance of any room thermostats or three-way valves, which
must therefore be managed separately as needed.
ÿ 3 = Boiler connected to the heating system and DHW storage tank.
ÿ 4 = Boiler connected to a centralized puffer managed with H2O probe connected to it.
Machine Translated by Google