klover PELLET FIRE PLACE 18 Quick start guide

ENGLISH
Pellet insert stove
PELLET FIRE PLACE
18, PELLET FIRE
PLACE 160 GLASS
INSTALLATION, USE AND MAINTENANCE,
USEFUL TIPS

SERVICE DECLARATION
Ref. Annex III EU Regulation no. 305/2011
DoP/KLOVER-035
1. Identification number
:
PFP18, FPG16
2. Model and/or lot no. and/or serial no. (Art.11-4)
:
PELLET FIRE PLACE 18, PELLET FIRE PLACE 160
GLASS
3. Intended use of the product according to the relevant
harmonised technical specification
:
Residental space heating appliance fuel by
wood pellets
4. Name or trademark of the manufacturer (Art11-5)
:
KLOVER s.r.l.
I - 37047 San Bonifacio (VR) –Via A. Volta, 8
5. Name and address of the representative (Art.12-2)
:
-
6. Assessment and verification system of the performance
constancy (Annex 5)
:
System 3
7. Notified laboratory
:
NB 1880
ACTECO s.r.l.
I - 33084 Cordenons (PN) –Via Amman, 41
Number of test report (based on System 3)
:
1880-CPR-004-17, 1880-CPR-004-001-17
8. Declared performances
HARMONISED TECHNICAL SPECIFICATION
EN 14785
PERFORMANCE FEATURES
PERFORMANCE
Fire resistance
A1
Distance from combustible material
200 mm
Fuel spillage risk
Pass
Emission of combustion products
-Nominal power
-Reduced power
CO at 13% of O20,010 %
CO at 13% of O20,052 %
Effective temperature
Pass
Electrical safety
Pass
Accessibility and cleaning
Pass
Maximum operating pressure
2,5 bar
Mechanical strength
NPD
Thermal performance
-Nominal power (reduced)
-Nominal power (reduced) yielded to the environment
-Nominal power (reduced) yielded to water
15,8 kW (4,4 kW)
3,5 kW (1,6 kW)
12,3 kW (2,8 kW)
Yield
-Nominal power
-Reduced power
ɳ 93,6 %
ɳ 96,0 %
Flue gas temperature
-Nominal power
-Reduced power
T 135,4 °C
T 58,0 °C
9. The performance of the product referred to in points 1 and 2 is compliant with the declared performance in
point 8.
This declaration is released on the sole responsibility of the manufacturer referred to in point 4.
Signed in the name and on behalf of the manufacturer by:
San Bonifacio (VR), 31/03/2017
Mario Muraro
Chairman of the Board

1
CONTENTS
CONTENTS ........................................................................................................................................................................ 1
INTRODUCTION................................................................................................................................................................. 3
IMPORTANT SAFETY INSTRUCTIONS................................................................................................................................... 3
INSTALLATION REGULATIONS ............................................................................................................................................ 4
HEALTH AND SAFETY........................................................................................................................................................ 4
THE MACHINE AND THE PELLETS ................................................................................................................................. 4
COMPONENTS OF THE APPLIANCE ..................................................................................................................................... 4
OVERALL DIMENSIONS...................................................................................................................................................... 6
CONNECTIONS DATA SHEET .............................................................................................................................................. 7
TECHNICAL SPECIFICATIONS............................................................................................................................................. 8
PELLET PROPERTIES ........................................................................................................................................................ 9
REQUIREMENTS OF THE PLACE OF INSTALLATION................................................................................................... 9
POSITIONING.................................................................................................................................................................... 9
SPACES AROUND AND ABOVE THE APPLIANCE.................................................................................................................. 11
EXTERNAL AIR INTAKE .................................................................................................................................................... 11
THE FLUE PIPE AND CONNECTION TO THE SAME ............................................................................................................... 13
CHIMNEY ....................................................................................................................................................................... 14
ELECTRICAL CONNECTION .......................................................................................................................................... 15
CONTROL OF ANY COUPLED BOILER ................................................................................................................................ 15
CONNECTION TO THE ROOM THERMOSTAT....................................................................................................................... 16
HYDRAULIC CONNECTION............................................................................................................................................ 16
THE DISPLAY .................................................................................................................................................................. 17
THE MENU ....................................................................................................................................................................... 19
INITIAL START-UP .......................................................................................................................................................... 23
FILLING THE SYSTEM FOR THE FIRST TIME........................................................................................................................ 23
PELLET LOADING AND CONNECTION TO THE MAINS POWER SUPPLY................................................................................... 24
IGNITION CYCLE ............................................................................................................................................................. 24
WORKING MODE............................................................................................................................................................. 25
SWITCH-OFF CYCLE........................................................................................................................................................ 25
CHANGING THE ROOM AND WATER TEMPERATURE ........................................................................................................... 25
PROBLEMS, ALARMS, USEFUL ADVICES ................................................................................................................... 26
USEFUL INFO….............................................................................................................................................................. 26
WHAT HAPPENS IF…...................................................................................................................................................... 27
ALARM SIGNALS ............................................................................................................................................................. 28
CLEANING AND MAINTENANCE ................................................................................................................................... 28
PRECAUTIONS BEFORE CLEANING ................................................................................................................................... 28
ROUTINE CLEANING........................................................................................................................................................ 28
NON-ROUTINE CLEANING ................................................................................................................................................ 29
MONTHLY CLEANING....................................................................................................................................................... 31
CLEANING THE CERAMIC GLASS ...................................................................................................................................... 32
CLEANING THE FLUE PIPE ............................................................................................................................................... 32
MAINTENANCE ............................................................................................................................................................... 32
PCB PARAMETERS ........................................................................................................................................................ 33
WIRING DIAGRAM........................................................................................................................................................... 35
WARRANTY CONDITIONS.............................................................................................................................................. 36

PELLET INSERT STOVE PELLET FIRE PLACE 18, PELLET FIRE PLACE 160 GLASS
2
EN - Rev. 2.2
Dear Customer,
First of all we would like to thank you for choosing a “KLOVER” product and we hope you will be satisfied with this
product.
Please read the warranty certificate carefully. This is found on the last page of this User Guide. Please contact the
authorised Technical Assistance Centre (TAC) for the initial start-up of your stove and to validate the warranty.
We would like to thank you again for trusting KLOVER products, and we would also like inform you that these models
are the result of forty years of experience in the manufacture of solid fuel products using water as heat transfer fluid.
Every single detail of the product is manufactured by qualified staff, using the most advanced equipment.
The manual contains a detailed description of the appliance and its operation, instructions for proper installation, basic
maintenance and control points, which must be periodically performed; furthermore it contains practical advice which
helps to obtain maximum performance from the appliance with minimum fuel consumption.
Stay warm with KLOVER!
Certificate number : KIWA 00007/033 B - KIWA 00007/034 B
Copyright
All rights reserved. The reproduction of any part of this manual, in any form, without the explicit written permission of
KLOVER Srl is forbidden. The content of this manual may be modified without notice. Although the documentation
contained in this manual has been carefully compiled and checked, KLOVER srl cannot be held liable for any damages
arising from the use of the same.
Copyright © 2015 KLOVER srl