KNIPEX 00 50 50 T LE User manual

KNIPEX Quality
EN KNIPEX Tethered Tools
Tool bags
Operating Instructions 00 50 50 T LE
00 50 51 T LE

2 Stand: 27.02.23
CONTENTS
1 General information 3
1.1 Notes on operating instructions 3
1.2 Symbols used 3
1.3 Copyright 3
1.4 Guarantee and warranty 3
2 Safety 4
2.1 Intended use 4
2.2 Safety Instructions for operation 4
2.3 Certiedsafety 5
3 Structure and function 6
3.1 Design of the Tool Bag 6
3.2 Function 7
3.3 Product Overview and Technical Data 7
3.3.1 Dimensions 7
4 Equipment of the Tool Bag 8
4.1 Transport of tools in the Tool Bag 8
4.2 Transport of bottles, spray cans or other objects in the side pockets 8
4.3 Transport of documents or tablet/PC in the front pocket 9
4.4 Labeling the Tool Bag 9
5 HowtousetheToolBag 10
5.1 TransportoftheToolBag 10
5.2 ConnectingtheToolBagtoprimaryanchoringlocations
(body, lifting device, or structure) 10
5.3 FasteningtoolsintheToolBag 11
5.3.1Tousethecarabinerend 11
5.3.2Tousetheloopend 11
5.3.3ConnectingAdapterStraps 12
5.4 Openingthetopcover 13
5.5 Useoftools 13
6 Inspection 14
7 Storage and Care 14
8 Disclaimer 14

GENEral iNfOrmaTiON
3 Stand: 27.02.23
1 General information
1.1 Notes on operating instructions
These operating instructions are for use with KNIPEX Tethered Tools
Tool Bag. The illustrations and descriptions contained in these operating
instructions may differ slightly from the Tool Bag actually delivered.
KNIPEX-Werk C. Gustav Putsch KG is not liable for damage caused by failure
to observe these operating instructions.
1.2 Symbols used
All safety instructions in this operating instructions are indicated by
corresponding symbols. The signal words at the beginning of each safety
instruction express the extent of the hazard.
Risk of serious to fatal injuries
This combination of symbol and signal word indicates an imminently
hazardous situation that will result in death or serious injury if not avoided.
Warning of potentially serious fatal injuries
This combination of symbol and signal word indicates a possibly hazardous
situation that may result in death or serious injury if not avoided.
Caution
Indicates a hazardous situation that, if not avoided, could result in minor or
moderate injury.
1.3 Copyright
These operating instructions and all documents supplied with the KNIPEX
Tethered Tools Tool Bag are protected by copyright and remain the property
of KNIPEX.
The reprinting of these instructions, even in part, is only permitted with the
written consent of KNIPEX Werk C. Gustav Putsch KG.
1.4 Guarantee and warranty
The manufacturer grants a statutory warranty in accordance with the
current sales and delivery conditions. No further warranties or assurances
are granted.
Within the warranty period, the warranty covers the rectication of all
defects that can be traced back to material faults or manufacturing errors.
Wearing parts are excluded from the warranty.
Warranty is voided if any of the conditions exist:
• Damage is caused through improper operation, use for purposes other
thanthosespeciedbythemanufacturer,orpoormaintenance.

SafETy
4 Stand: 27.02.23
2 Safety
2.1 Intended use
The products are intended for the following uses:
• AllelementsoftheKNIPEXTetheredToolsSystemaredesignedtobe
used for tool tethering only. The weight of the tool must not exceed the
permitted capacity for any tethering system component.
• OnlyconnectKNIPEXTetheredToolsLanyardsorAdapterStrapstotools
with captive tethering points that are engineered as tether points.
Any use beyond the intended purpose or any unauthorized modication
shall be considered improper. The operator shall be liable for damages
resulting from improper use.
Intended use also includes adhering to these operating instructions. They
must be read and understood in full before use.
The users must be trained regarding to tool securing and the safe use of
tools at heights. In order to reduce the hazards of working at heights
with tools, the following instructions must be followed to avoid the risk of
serious injury or death.
2.2 Safety Instructions for operation
Risk of falling from slipping, stumbling, twisting and from people
falling onto a lower surface or an object!
KNIPEX Tethered Tools Tool Bags are for tool transport only. They are not for
human or animal support, nor are they intended to be part of a human fall
protection system.
Risk of injury from moving parts!
Do not use around machinery with exposed turning or moving parts.
Risk of falling due to falling heavy tools!
Heavy, falling tools can make you loose your balance and falls can
occur.
Ifpossible,useaseparatexedanchorpointforequipmentwithweights
over 2.26 kg (5 lbs).
Risk of injury from falling objects!
Observe the following safety instructions when using KNIPEX Tethered Tools
Tool Bag.
• Never exceed the permitted capacity for any tethering system component.
• EachKNIPEXTetheredToolsToolBagMUSTbeinspectedpriortoeach
use in accordance with the Instruction Manual.
• If a KNIPEX Tethered Tools Tool Bag has been subject to fall arrest
forces, it must be immediately inspected for damage by a competent
person prior to continued use. If any doubt, it must be removed from
service.

SafETy
5Stand: 27.02.23
• DonotmakemodicationstotheKNIPEXTetheredToolsToolBag
• Never make attachments to tools or equipment in a manner that
would allow the KNIPEX Tethered Tools Tool Bag to be unintentionally
disconnected.
• Ensure the KNIPEX Tethered Tools Tool Bag is kept free from any and
all obstructions including, but not limited to, entanglement with other
workers, yourself, and surrounding objects.
• Do not use a KNIPEX Tethered Tools Tool Bag if it will interfere with
the safe working condition, or operation of the tool or equipment it is
attached to.
• OnlyconnectKNIPEXTetheredToolsToolBagtoAnchorPointsthatare
suitable and reliable for tool tethering.
• Only connect KNIPEX Tethered Tools Tool Bag to tools with captive
tethering points that are engineered as tether points.
• Ensure there is adequate clearance in the event of a tool drop. Tool
fall/swing path must not endanger yourself, other personnel, or any
surrounding equipment or materials.
• Do not use the KNIPEX Tethered Tools Tool Bag in temperatures below
-35°C/-30°Forabove45°C/113°F.
General notes
• AllproceduresshownintheseinstructionsareforKNIPEXTethered
Tools Tool Bags only.
• Allincidentsofdroppedtoolsshouldbereportedtoyoursupervisoror
safety coordinator. Involved KNIPEX Tethered Tools Tool Bags must be
inspected for damage immediately (see chapter "Inspection").
2.3 Certied safety
TESTED & CERTIFIED
IN GERMANY
fit for use
loading capacity tested
ID 7616
www.VPA-zert.de
The products are tested and conform according to
ANSI ISEA 121-2018.
The usability and loading capacity of the Tool Bags
havebeenindependentlytestedandcertied.
(VPATESTEDbyVPAPrüf-undZertizierungsGmbH,
42859RemscheidGermany)

STruCTurE aNd fuNCTiON
6 Stand: 27.02.23
3 Structure and function
3.1 Design of the Tool Bag
1
12
11
6
5
13
10
4
7
89
2
3
Figure 1: Termsanddenitions-Example005050TLE,10.0kg(22lbs)
1 Top Cover
2 Hookandloopfastener(likeVelcro)forindividuallabelingwith
badges (100 x 200 mm)
3 Carrying strap (for transport on solid ground only)
4 Side pocket (left and right side) e.g. water bottles or spray cans
5 Tool holder (left and right side)
for e.g. tape measure or cordless drills
6 2 elastic loops to keep the cover open
7 3 D-rings on the backside
toattachthebagtoclimbingequipmentoraxedpoint
-Part#005050TLE:maximumstaticload10.0kg(22lbs)
-Part#005051TLE:maximumstaticload15.0kg(33lbs)
8 Reinforcedbottomwith5rubberfeet
9 4 D-rings at the rear of the inside to attach the tools
10 Inside
2 compartments for tools, 4 D-rings at the rear (position 9),
1 D-ring each at the left and right side,
18 elastic band tool loops
11 Pocket for documents or tablet/PC,
holder for 2 pens
Max. document size:
005050TLE: DINA5(148x210mm/5.8“x8.3“)
005051TLE: DINA4(210x297mm/8.3“x11.7“)
12 Hookandloopstrapstoclosethedocumentpocket
13 1 D-ring on the left and right side
for fastening the carrying strap for transporting the Tool Bag on
solid ground
-Part#005050TLE:maximumstaticload10.0kg(22lbs)
-Part#005051TLE:maximumstaticload15.0kg(33lbs)
ORforattachingKNIPEXtetheredtools(maximumdynamicload
3.0 kg / 6.61 lbs )
Only tools weighing less than 3.0 kg / 6.61 lbs may be
attached to the 8 D-rings (6 in the inner compartment
and one each on the left and right outside of the bag).

STruCTurE aNd fuNCTiON
7 Stand: 27.02.23
3.2 Function
Tools that do not exceed the permitted capacity for any tethering system
component and have a captive tethering point engineered into them can
betetheredwiththeKNIPEXTetheredToolsLanyardsandAdapterStraps.
3.3 Product Overview and Technical Data
Product No. Type Height
(H)
Width
(W)
Depth
(D)
Load
rating
Weight
005050TLE Tool bag 300 mm
(12")
250mm
(10")
150mm
(6")
10.0 kg
(22 lbs)
1.4 kg
(3 lbs)
005051TLE Tool bag 470 mm
(18")
250mm
(10")
150mm
(6")
15.0kg
(33 lbs)
1.6 kg
(3.5lbs)
3.3.1 Dimensions
W= 250
BB
D= 150
H
Figure 2: Dimension drawing
H:HeightoftheToolBagwithcoveropen(seetable)
B: When the outer pockets are full they expand up to 60 mm / 2.36" wider

EquipmENT Of ThE TOOl BaG
8 Stand: 27.02.23
4 Equipment of the Tool Bag
Figure 3: AttachmentoftoolsandotherobjectswithLanyardsorAdapterStraps
(TOOLSNOTINCLUDED!)
4.1 Transport of tools in the Tool Bag
Tools can be transported in the two inner compartments. The total weight
ofthebagmustnotexceed10kg/22lbs(005050T)or15kg/33lbs
(005051T).
Each tool and object in the Tool Bag must be attached to one of the D-rings
withaLanyardorAdapterStrap.
Tools can be inserted into the elastic band tool loops on the inside of the
bagtofacilitateaccesstotheindividualtoolsandtoxtheminthebag.
4.2 Transport of bottles, spray cans or other objects in the side
pockets
Bottles, spray cans (e.g. grease or marking sprays) or other objects can be
transported in the side pockets of the Tool Bag.
These items must also be attached to one of the D-rings via a lanyard using
suitablefasteningmaterialforcansandbottles(seegure3).

EquipmENT Of ThE TOOl BaG
9 Stand: 27.02.23
4.3 Transport of documents or tablet/PC in the front pocket
Figure 4: Closing the document pocket
Documents and tablet/PC can be stored in the front pocket for easy
transportation.
The frontpocketmust be closedwith the twoaps with hookand loop
fastener. Documents or a tablet/PC must be additionally fastened to a D-ring
with a Lanyard using suitable fastening material.
4.4 Labeling the Tool Bag
Figure5: Labeling the Tool Bag
The hook and loop fastener on top of the bag can be used for individual
labeling of the Tool Bag with badges. Labels with hook and loop fasteners
can be attached here, e.g. to mark the contents of the bag.
Tools must not be attached to the hook and loop fastener!

hOw TO uSE ThE TOOl BaG
10 Stand: 27.02.23
5 How to use the Tool Bag
5.1 Transport of the Tool Bag
For transporting the Tool Bag on the ground, a carrying strap can be hooked
onto the two D-rings on the side.
Risk of injury from falling objects!
The carrying strap is only suitable for transport on solid ground.
The carrying strap must not be used to pull the bag up onto a scaffold.
The carrying strap must not be used to attach the bag to climbing
equipment or structures at height.
AttachasuitableliftingdevicetotheD-ringsontheoutsideofthebagif
you want to pull the bag up.
5.2 Connecting the Tool Bag to primary anchoring locations
(body, lifting device, or structure)
Figure 6: Tool Bag anchored to a structure
1. During ascent and descent, tools and bag can be attached to the
climbing equipment. Make sure that it is as close to the body as
possible and cannot get caught. If it is possible to pull up the tools and
bag separately, this option is preferable.
2. Toolsweighingmorethan2.26kg(5lbs)must,wheneverpossible,be
anchored to a structural anchorage or lifting device.
3. For best practice anchor your Lanyard to a structure other than the
users body. If the user does anchor the Lanyard to their body, select an
anchor location in the middle of your body. Be sure to have a secure
stance, because falling tools can make you lose your balance.
4. For any questions or concerns about selecting appropriate anchor
points,consultaqualiedperson.
AttachtheotherendoftheLanyardtoananchorpointthatissuitableand
reliable for tool tethering either by loop or by a carabiner.