Sealey PTB39003 User manual

3 DRAWER HANG-ON LOCKER-HEAVY DUTY
MODEL NO: PTB39003
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this locker.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
9Keep the locker clean and tidy in accordance with good workshop practice.
8DO NOT use the locker for any purpose other than that for which it is designed.
8DO NOT step on the shelves or drawers.
8DO NOT overload the locker.
8DO NOT clean the locker with any solvents which may damage the surfaces or protective coating.
2. INTRODUCTION
Hang-On locker suitable for heavy-duty Premier rollcabs. Heavy-duty welded steel construction for strength and durability. Textured
powder coat both solvent and rust resistant. Ball bearing drawer slides provide superior performance and carry heavier loads. All drawers
have full width sand blasted aluminium ‘Lift & Latch’ drawer pulls, making easy access while preventing inadvertent opening when box is
being moved. Non-slip drawer liners supplied for all drawers. Integral locking system locks all drawers in each unit with the turn of a key.
All supplied with 2 keys. Manufactured to the highest levels of construction to withstand the toughest of workshop/garage conditions.
3. SPECIFICATION
Model No. ............................................................. PTB39003
Overall size (W x D x H)........................390 x 460 x 1390mm
No. of Drawers.....................................................................3
No. of Shelves......................................................................2
Weight............................................................................ 41kg
4. CONTENTS
5. ASSEMBLY
NOTE: Heavy item - get assistance to assemble.
5.1.  Securelyattachhanger(g.1-item2)usingscrews(g.1-item1).
5.2.  Placeneoprenepadspacers(5x40x80)nearloweredgeoflocker.(seeg.2).Thespacerpadshaveadhesivebackstoenable
 xing.
5.3.  Attachconnector(g.1-item4)totheundersideofthelockerusingtheboltsandwashers(g.1-items5&6)(seeg.3andg.4).
5.4. Hang the locker onto the side of the cabinet.
5.5.  Fromtheunderside,adjustthelocationoftheconnectortofullyengageitwithmaincabinet(seeg.3andg.4).
Tighten securely when in correct position.
PTB39003 Issue 1 21/08/18
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear protective
gloves
fig.1
ITEM DESCRIPTION QTY
1 M6 x 16 C/Sunk Screw 4
2 Hanger 1
3 Magnet 3
4 Connector 1
5 Washer 2
6 M6 x 20 HHB 2
7 Slide Set 3 sets
8 Drawer liner 3
9 Shelf support 8
10 Lock 1
11 Shelf liner 3
12 Neoprene pad spacers 2

5.6.  Tosupportshelves,insertshelfsupports(g.1-item9)atthedesiredheightmakingsurethatall4areatthesamelevel(g.5).
Original Language Version
© Jack Sealey Limited
fig.2
fig.3
fig.4
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
PTB39003 Issue 1 21/08/18
fig.5