KONDO KAGAKU Co., Ltd.
Service department
TEL : 03-3807-7648 (service)
Hours of operation:9:00-12:00 & 13:00-17:00 M-F except national holidays Saturday
and Sunday closed
ADDRESS : 4-17-7 Higashi-Nippori, Arakawa-ku Tokyo Japan 116-0014 Japan
Latest information can be accessed here. >> http://www.kopropo.co.jp
The Servo Model Selector for 4S cannot be used with models earlier than the RSx3/ BSx3series.
※Some models, such as Grasper 2, cannot change the model memory if they are set to IDs 5-8.
Remove connector of servo from the receiver that you want to change the memory
for.
Connect servo connector to (1)Servo connect pin in the Servo model Selector.
Note) Be careful of the direction of the connector.
Connect (2)Receiver (or Power) to Connector of receiver.
This is to get a power supply for Servo Model Selector .
The Channel of the receiver to be used does not matter.
You can use an Electrical Switch or other power supply(6 to 7.4V)
When the power source of the receiver
is turned ON,
the (3)LED will blinks fast at 3 seconds.
After 1 second, the (3)LED will go out
and starts blinking at a low speed.
The Numbers of blinks is the model
number that is currently selected.
If you push (4)push switch, the number of times the LED is blinking is increasing
each time it is pressed. Please select number of blinks.
* Model number of servo is changed when you change the number of
blinks.
Please turn off receiver’ s power and disconnect all connectors in “Servo Model
Selector” .
Servo lead is inserted in the connector of the receiver.
*Be careful not to make a mistake in the connecting channel.
The Servo Model Selector for 4S is a product that changes the model memory selection of KO PROPO 4S series servos easily.
(1) Servo connect pin
Servo
(3) LED
(4) Push switch
(2) Receiver
（ or Power）
■
Thank you for purchasing this product. Please refer often to this manual before using the
product. Also please keep this manual for future references and refer to it at anytime.
Ver.1.0.0
Servo Model Selector for 4S
●The prerequisite condition of this product is that it is used in combination
with other KO PROPO products. We cannot assume any responsibility for
the use of other company’ s products with this product.
●Vibration during usage can damage the servo. Use the rubber grommets
included to prevent the servo from coming in contact with mechanical
plates. Over tightening the grommets reduces the effect of preventing
vibration.
●Check any linkage connected to the servo for free movement. Loose or
bound linkage will increase power consumption, which may shorten the
operational life of the servo.
●When using dry cells as a power supply, the correct performance may not
be shown.
●Modification of the unit by the customer may render the product
un-repairable.
* Specifications may change without notice due to performance
improvements.
Noted regarding the servo product. Note on usage
This display shows the content to which a possibility and/or a disadvantageous accident
may occur causing injury.
•The connection of a servo should only be used with our company’ s products for the
best result .
Our company does not assume the responsibility of damage, etc. that may occur
because of the use of this product in combination with other manufacture’ s products.
•Confirm the connector direction and make sure it is securely inserted. If the connector
becomes loose due to vibration during a run, it will drive recklessly.
•Do not use in a place where there are puddles or rain. *Water may enter the equipment
and cause damage internally.
•Resolve any problems before proceeding and do not remodel the product.
Attention
Danger
The following displays the content of danger that can cause serious injury, death and etc.
While operating this product, do not carelessly touch, put it to your face or etc.
*There is danger of fracturing or cutting your finger or other parts of your body from the
strong torque output of the output axis. There is also the danger of being burned due to
the heat generated if the servo is over-loaded.
■ Read me First
Name of each part and Usage product.
Contact us
■Because the product has exposed components, please pay
attention to the short circuit of the product from metal and
other conductive materials.
■Servo operation will become abnormal when you mistake the
procedure of the connection.
■If LED is fast blinking again after fast blinking when powered
ON, it is a sign of communication error. Please turn of the
power and check servo wire connections.
■Please use the voltage with a power source of 6~7.4v.
■This unit can not be use when you drive a car. Please remove
after settings are done.
■When there is a strange smell or hot temperature, please stop
using and turn off power.
Attention
If you need repair or you have any question.
First, please contact to shop or distributor that you bought this product.
If you can not contact them, please contact us directly.
Instruction Manual
*＜Compatible products＞4S serial servos with Model memory function.
1.
2.
3.
4.
5.
6.
7.
8.
※5 different model memories can be installed. Please install different settings to each model memory beforehand.
※For write of setting to 4S serial servos, please use EX-NEXT or LCD Xpansion unit EXP-201.
Receiver
2
3
1.
off off
blinks
Pattern of Model Number
5.
