KoamTac SKX SmartSled SKXSLED-UHF 1.0W User manual

1 X SKXSLED-UHF 1.0W
1 X 6000mAh Lithium-Polymer Battery
1 x Companion Cushion (SKXPro or SKX5)
*SKX sold separately. Tweezers and PH0 screw driver
(notincluded) will be necessary to complete assembly.
What’s in the Box?
1.0W UHF Reader Companion Assembly
Using tweezers, carefully remove all four (4) screw caps
from the back of the SKX
™
SmartSled
®
. Then, remove all
(4) screws from the back of the SKX. (A)
1. Remove the blue protective film from the front of the
companion PCB. Next, attach the contact board to the
back of the SKX5 as shown in the image. (D)
1. Remove the blue protective film from the front of the
companion PCB. Next, attach the contact board to the
back of the SKXPro as shown below. (B)
2. Remove the transparent protective film from the back
of the companion cushion and attach it to the back of
the SKXPro as shown below. (C)
2. Remove the transparent protective film from the back
of the companion cushion and attach it to the back of
the SKX5 as shown below. (E)
1. Remove the blue protective film from the top of the
SKXSLED-UHF1.0W. (F)
8 screws + 1 extra
1x Contact PCB (SKXPro or SKX5)
SKXPro
Contact PCB
SKX5
Contact PCB
SKXPro or SKX5
Companion Cushion
SKX 1-Slot Charging Cradle
SKX 5-Slot Charging Cradle
XCover 1-Slot Charging Cradle
XCover 5-Slot Charging Cradle
SKXSLED-mPOS
SKXSLED-MSRIC
SKX™SmartSled®
1.0W UHF Reader Companion
Assembly Manual
* All pictures shown are for illustration purposes only.
* Actual product may vary.
Contact PCB Assembly - SKXPro
Contact PCB Assembly - SKX5

2. Align the screw holes of the SKXSLED-UHF 1.0W with
the screw holes of the SKX. (G)
6,000mAh Lithium-Polymer Battery
Battery Status
3. Use the eight (8) included screws to attach the
SKXSLED-UHF1.0W to the SKX as shown as below. (H) 1. Turn the battery door knob counterclockwise and open
the battery door as shown below. (I)
2. Insert the battery into the SKXSLED-UHF1.0W using the
inner guide groove. (J)
3. Close the battery door and turn the battery door knob
clockwise to lock. (K)
*The LED blinks when the battery is in use.
When the device is charging
When the battery is in use and
device is discharging
Red: Low Battery
Orange: Charging
Green: Fully Charged
Blinking Red: Low Battery
Blinking Orange: Discharging
Blinking Green: Fully Charged
Toggling Read Modes
There are two read modes in which the SCAN or Trigger
buttons work and they are toggled via hotkey command.
* Please refer to figure for location of keys 1 and 2.
• Hotkey: Input SCAN Buttons 1, 1, 2, 2, 1, 2 within 3 sec.
• Barcode Mode: When entered into this mode, 1 long and
1 short beep will be heard. Barcodes can be read with
SCAN or Trigger buttons.
• Tag Reading Mode: When entered into this mode, 1 long
and 2 short beeps will be heard. UHF tags can be read
with SCAN or Trigger buttons.
Changing Tag Read Mode
There are 3 tag read modes: Active, Single, or Multiple.
The tag read mode is changed by scanning one of the
following barcodes:
Active Read Mode
Simultaneous reading of multiple tags while pressing
SCAN or Trigger buttons.
Active Read Mode
Single Read Mode
Only one tag is read each time the SCAN or Trigger
button is pressed.
Single Read Mode
Multiple Read Mode
When pressing SCAN or Trigger buttons, multiple tags are
simultaneously read for the set duration (default: 10 seconds).
* Time setting can be changed in Settings ->Reading Timeout.
Multiple Read Mode
20211005
933321
12
Trigger
Button