Kobo MT-101 User manual

1

WARNING
SAFETY PRECAUTIONS
Thank you purchasing our product. Even though we go efforts to ensure the quality of each product we
produce, occasional errors and/or omissions do occur. In. any event should you find this product to
have either a defective or a missing part please contact us for a replacement.
This product has been designed for home use only. Product liability and guarantee conditions will not
be applicable to products being subjected to professional use or products being used in a gym center.
This exercise equipment was designed and built for optimum safety. However, certain precautions
apply whenever you operate piece of exercise equipment. Be sure to read the entire manual before
assembly and operation of this machine. .Also, please note the following safety precautions:
CAUTION : Before starting any exercise program, it is recommended that you consult you Physician.
IMPORTANT SAFETY INFORMATION
1. Locking knob must be fully inserted in upper hole of left support frame, when in fold up or storage
position, to secure treadmill frame and avoid possible injury form treadmill frame unintentionally
folding down.
2. Locking knob must be fully inserted in lower hole of left support frame and treadmill frame, when in
fold down or operating position, to secure support frame and avoid possible injure from support
frame unintentionally folding down.
3. Do not allow children on or around treadmill.
4. Handle append individuals should have medical approval and close supervision when using this
appliance.
5. Always keep hands and legs off of the treadmill while other are using it.
6. Use the treadmill only for it’s intended use as described in this manual.
7. Always use treadmill on a level surface.
8. Do not insert any object into any opening.
9. Start your program slowly and very gradually increase your speed and distance.
10. Do not walk or jog barefoot or in stocking fee.
11. Do not walk or jog in loose fitting shoes or slippers.
12. Never walk or jog while wearing loose fitting, long garments such as slacks, pajamas, dresses or
floppy bell bottoms.
13. Read all instructions carefully before assembly and operation.
14. Always hold onto HANDRAIL while mounting, during use and dismounting treadmill.
2

PARTS AND EXPLODED VIEW
3

ON DESRIPTION QT'Y ON DESRIPTION QT'Y
1 MAIN FRAME 1PC 26 BOLT M8*80L 3PCS
2 BASE FRAME 1PC 27 HEX-HEAD BOLT M10*70L 2PCS
3 UPRIGHT PILLAR 1PC 28 BOLT M8*40L 4PCS
4 SIDE HAND POST(L+R) 2PCS 29 BOLT M8*20L 4PCS
5 FRONT HANDLEBAR 1PC 30 BOLT M8*50L 1PC
6 HANDLEBAR 2PCS 31 SPEACIAL BOLT M8*60L 1SET
7 HANDRAIL BAR 2PCS 32 SCREW M5*10L 2PCS
8 HANDRAIL FOT TEISTER 1PC 33 SCREW M5*10L 2PCS
9 UP FOLDING CONNECT-1 1SET 34 SCREW M5*15L 1PC
10 WAIST TWIST TRAY 1PC 35 WASHER φ28*φ10.5 5PCS
11 PEDAL TUBE(L+R) 2PCS 36 WASHER φ22*φ8.3 25PCS
12 CYLINDER 2PCS 37 ARC WASHER φ25*φ10.5 2PCS
13 BOLT PIN 1PC 38 WRENCH S13-14-15 1PCS
14 PULLEY 1SET 39 WRENDH S5 1PC
15 COMPUTER 1PC 40 ARC WASHER φ22*φ8.3 6PCS
16 WHEEL PLASTIC COVER 1PC 41 NUT M8 16PCS
17L PUSH-UP PIPE-L 1PCS 42 KONB 1PC
17R PUSH-UP PIPE-R 1PCS 43 UNDER FOLDING CONNECT -2 1PC
18 COMPUTER WIRE 1SET 44 SHORT PIN 2PCS
19 SENSORWIRE CONNECTOR 1SET
20 NYLON BELT 1PC
21 HEX-HEAD BOLT M10*60L 2PCS
22 HEX-HEAD BOLT M10*50L 1PCS
23 BOLT M8*45L 3PCS
24 HEX-HEAD BOLT M10*15L 2PCS
25 CARRIAGE BOLT M8*50L 6PCS
PARTS LIST
4

5

Step 1
*Attach the left and right upright(4L / 4R) to the base
frame(2). Secure using two bolts 8*50mm(25). Two
washers 8mm(36) and two Nuts(41).
*Attach the upright pillar(3) to base frame using two bolts
8*50mm(25). Two washers 8mm(36) and two
Nuts(41).
Tighten with hand to leave room for adjust in Step 1
Step 2
*Attach the main frame(1) to the left and right upright
(4L / 4R). Using two washers 10mm(35) and two bolts
10*60mm (21).
*Attach the plastic cover(16) on main frame(1) using
screws 5mm(32).
*Connect upright extension wire(18) and speed pickup(18).
Tighten with hand to leave room for adjust in Step 2
6
STEP 1.
STEP
2
.

Step 3
*Attach waist twist tray(10) to upright pillar(3). Secure
using bolts 8*80mm(26) and washer(36) ,secure using
nuts (41).
*Attach bolt(31) to upright pillar(3),using
washers(36) and nuts(41).then secure using bolt(42)
*When fold the waist twist tray(10) to upright(3) position, you
must insert the waist twist tray to the Bolt (31) and fixed through
the bolt hole located in twist tray with bolt(42).
Tighten with hand to leave room for adjust in Step3
Step 4
*Attach pedal(11L / 11R) to upright pillar(3). Using
washer(36). Secure using two bolts 8*20mm(29).
*Attach adjustment(12) to upright pillar(3). To
washer(36). Secure using two bolts 8*20mm(29).
*Attach two Hydraulic cylinder (12) to two pedal(11L / 11R)
Using washers(36) and two bolts 8*45mm(23).
Secure using two nuts(41).
* Insert Pulley(14) to upright pillar(3) .
*Attach wire of Pully(14) to pedal(11L / 11R) by using
washers(35) and two bolts 10*15mm(24).
Tighten with hand to leave room for adjust in Step4
7
STEP 3.
STEP
4
.

Step 5
*Attach the front handlebar(5) to upright pillar(3) using
washer(35) and two bolts 10*50mm(22).
*Attach the handlebar(6) to the front handlebar(5) using
washer(40) and two bolts 8*40mm(28). Attach the hand-
lebar(6)to the left and right upright (4L / 4R)using washer(37)
and two bolt(27).
*Connect the upper extension wire(18) of handlebar(5) to the
back wire of the Computer(15). Connect the upper extension wire(19)
of handlebar(5)to the sensor wire connector(19).
Tighten with hand to leave room for adjust in Step5
Step 6
*Insert two “AA” batteries into the back of the computer (15).
*Connect the upper extension wire(18) of handlebar to the back
wire of the computer (18). Connect the upper extension wire(19)
to the back wire of the computer(19).
*Attach the computer(15) toupright pillar(3), secure with two
bolts 5*10mm(33).
*Attach handrail (8) to upright pillar(3). Using washer(40)
and two bolts 8*80mm(26). Secure using nut(41).
*Put unders folding connect tube(43) in up connect tube(9).
And connect folding tube(43) to left upright tube of main
frame(1) using bolt(23), 2 washers(36) and nut(41). Attach up
connect tube( 09 ) to base frame(2) using bolt(30), 2
washers(36) and nut(41).
*when storing the treadmill lift up the end of treadmill as
shown, and Open BOLT PIN lock (13) , move the treadmill
frame pop BOLT PIN in place (13) can be adjusted by turning
the knob.
Tighten all nuts and bolts after finish Step 6 8
STEP
5
.
STEP
6
.

Step 7
*Insert push-up bar(17L / 17R) to waist twist
Tray(10) using washers(36) and bolt
(28) and nuts(41)
9
STEP
7
.

IT IS EASY FOR STORAGE
①
CAUTION
You must Close up the pedal making it
Folding then using the fixed rope in upright
Pillar(3).
See diagram left.
2
CAUTION
When storing the treadmill, you must secure the
main frame with the locking bolt (13) by pulling
it out through the bolt hole located near the
bottom of your treadmill.
See diagram right.
10