Kodak PROFESSIONAL LED II 20R User manual

© Eastman Kodak Company, 2000
{SiteSpecifications}{Production}{KodakServiceSupport} Publication No. SS2616-1
23NOV99
Supersedes SS2616-1
15JUL97
SITE SPECIFICATIONS
for the
KODAK PROFESSIONAL LED II PRINTERS 20P/20R
KODAK PROFESSIONAL LED II PROCESSOR 20P
G130_1000HA

223NOV99 – SS2616-1
PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the
subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice, and
makes no warranty, express or implied, with respect to this information. Kodak shall not be
liable for any loss or damage, including consequential or special damages, resulting from any
use of this information, even if loss or damage is caused by Kodak’s negligence or other fault.
Description Page
Table of Contents
Site Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Plumbing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Venting Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Site Specifications
SS2616-1 –23NOV99 3
Section 1: Site Specifications
Space Requirements
Dimensions and Weight (Uncrated)
Site Access:
Doorways to the site should be 91centimetres (36 inches) wide, or larger. The front and rear PRINTER FRAME
DOORS, SHEET TRANSPORT MODULE DOORS, and the OPERATOR CONTROL PANEL (OCP) must be
removed to move the PRINTER through a 36 inch doorway.
Minimum acceptable door size is 71.2 centimetres (28 inches). The enclosures, covers, and subassemblies for the
PAPER SUPPLY MODULE, the KNIFE AND SHEET TRANSPORT MODULE, and the TAKE-UP MODULE†
must be removed to move the PRINTER through a 28 inch doorway.
†Roll-to-roll system only.
Operator and Service Access:
When fully assembled, the system requires a minimum of 91 cm (36 in.) on each side to allow access for service and
operator maintenance.
Floor:
The system should be installed on a smooth, hard, and level floor surface. Floor pitch should not exceed 1 inch in 5
feet.
Operating Environment
The unit to be installed is an Insulation Catagory Type II machine and operates in a Pollution Degree 2 environment
in accordance with IEC 664 ( Normal Office Environment ).
* Room temperature changes of more than 5 degrees during operation will require recalibration of the PRINTER.
**Although the PRINTER and PROCESSOR operate in normal room lighting, access to a darkroom is required for
loading paper into cassettes.
Width Length Weight
Printer:
102 cm (40 in.) 149 cm (58.5 in.) 420 kg (925 lbs) 429 kg (945 lbs) with
paper.
Processor:
87.6 cm (34.5 in.) 130 cm (51 in.) without removable print
rack.
198 cm (78 in.) with print
rack installed.
172 kg (380 lbs)
312 kg (471 lbs) with
processing chemicals.
Roll-to-roll Printer:
102 cm (40 in.) 189 cm (74.5 in.) 510 kg (1125 lbs) 519 kg (1145 lbs) with
paper.
Description Specification
Temperature* 15.5-26.6°C (60-80°F) for unplumbed
systems15.5-30°C (60-86°F) for plumbed
systems
Relative Humidity 15-76%
Altitude 0-2000 metres (6562 feet)
Lighting maximum of 325 lux **
(30.2 foot-candles)

SITE SPECIFICATIONS
423NOV99 –SS2616-1
Electrical Requirements
Power
** Phase selection must be completed by CES personnel.
*** Outside the U.S. and Canada, amperage for the PRINTER is 16A, and the amperage for the PROCESSOR is
32A.
Note
To prevent processor failures caused by power fluctuations, purchase a Square-D Buck and Boost Transformer
(Model #500SV43F) EK Catalog #869-7799. Other transformers may not provide satisfactory results.
Within the US and Canada, the PRINTER is supplied with a 2.4-metre (8-foot) POWER CORD. The power
receptacle must be located within 1.2 metres 30 cm (4 feet 1 foot) of the rear of the PRINTER. This power receptacle
should be a dedicated line with a separate CIRCUIT BREAKER. The receptacle must accept a PLUG which
conforms to NEMA N6/15 (printer plug specification). Outside the US and Canada, the region will supply the
appropriate locally approved POWER CORD and PLUG. The POWER CORD should be cretified and approved by
a national test house.
Within the US and Canada, the PROCESSOR is supplied with a 2.4-metre (8-foot)POWER CORD which enters the
cabinet from below. The power receptacle must be located within 2.4 metres 30 cm (4 feet 1 foot) of the rear of the
PROCESSOR. This power receptacle should be a dedicated line with a separate CIRCUIT BREAKER. The
receptacle must accept a PLUG which conforms to NEMA L6-30P (processor plug specification). Outside the US
and Canada, the region will supply the appropriate locally approved POWER CORD and PLUG.
A PROTECTIVE EARTH GROUND must be supplied when installing the PROCESSOR.
Voltage Range/
Frequency*** Power Consumption
Roll-to-processor Printer: 200-254V,
47-63Hz, 1phase, 15A
Processor: 208-254V,
47-63Hz, 1phase or 3
phase**, 30A
Less than 9.12kVA.
Roll-to-roll 200-254V, 47-63Hz,
1phase, 15A Less than 2.4kVA.

Site Specifications
SS2616-1 –23NOV99 5
Space requirements for a roll-to-processor system
Printer Processor
4.5 meters (179 in.)
2.9 meters
(114 in.)
30A
1.5 meters (60 in.)
.91 meters (36 in.)
minimum
.91 meters (36 in.)
.91 meters (36 in.)
.91 meters (36 in.)
minimum
minimum
minimum
G130_0600DA
3.5 meters + .3 meters (138 in. + 12 in.)
2.2 meters + .3 meters (86 in. + 12 in.)
_
__
_
*
*SCSI−2 connection from host here
15A
External modem connection here

SITE SPECIFICATIONS
623NOV99 –SS2616-1
Space requirements for a roll-to-roll system
SCSI Connection to Host Computer:
The proper configuration of the SCSI-2 connection will depend on the distance of the host computer from the
PRINTER.
A single-ended connectioncan be usedif the total distance is less than 6 metres (19.7feet). The customermust supply
a SCSI-2 data CABLE (FAST 20 type) and a SCSI-2 TERMINATOR for single-ended connection. An active FPT
type (forced perfect termination) SCSI-2 TERMINATOR is recommended.
A differential connection must be used if the distance is between 6 and 22.9 metres (19.7 and 75 feet). The customer
must supply a SCSI- 2 data CABLE and a SCSI-2 TERMINATOR for differential connection. A differential SCSI-
2 TERMINATOR is required.
Switching from a single-ended to a differential SCSI-2 connection requires a reconfiguration of the FEE BOARD.
Refer to the INSTALL INSTRUCTIONS for detailed information on how to do this.
Locate SCSI-2 CABLES away from any source of electrical interference (e.g. transformers, fluorescent light ballast).
2.2 meters + .3 meters (86 in. + 12 in.)
__
*
*
SCSI−2 connection from host here
Printer
3.8 meters (149 in.)
2.9 meters
(114 in.)
15A
1.5 meters (60 in.)
.91 meters (36 in.)
minimum
.91 meters (36 in.)
.91 meters (36 in.)
.91 meters (36 in.)
minimum
minimum
minimum
G130_0601DA
External modem connection here

Site Specifications
SS2616-1 –23NOV99 7
Plumbing Requirements
Water Supply:
Adequate water supply and drainage is the customer’s responsibility, and must be installed to specifications by the
customer before installation of the PROCESSOR begins.
A WATER SUPPLY PANEL for plumbed systems is available from Kreonite (WPS-A), and is recommended.
Kodak willinstall flexible supply lineto PROCESSOR and anelectrical connection to the SOLENOID. The WATER
SUPPLY PANEL should be wall-mounted within 4.9 metres (16 feet) of the rear of the PROCESSOR.
Technical support and warranty of WATER SUPPLY PANEL is the responsibility of Kreonite.
Water to a plumbed system must meet the following specifications:
Flow rate: 3.8-20 liters per minute (1-5 gallons per minute)
Temperature: Hot- 59 C (120 F) minimum temperature. Cold-27 C (80 F) maximum temperature. Practically, the
water temperature should be adjusted to ≥35C (95 F) to minimize the time necessary to bring the PROCESSOR to
operating temperature.
Waste Water:
A floor drain should be located convenient to the PROCESSOR.
The drain system should conform to local specifications for silver-laden bleach-fix, and stabilizer or waste water.
Kodak will install a flexible drain TUBE to the PROCESSOR. The customer will be responsible for connection of
the flexible drain TUBE to a locally approved drain system.
In unplumbed systems, the PROCESSOR is supplied with 10-litre CONTAINERS for easy transport of waste to the
site waste facilities. Waste CONTAINERS will be located under the PROCESSOR.
A sink, 61 cm (24 in.)wide or larger, located near the PROCESSOR, is recommended for use during cleanup.
Venting Requirements
For a roll-to-processor system, 10 complete changes of air in the room per hour are required.
For a roll-to-roll printer, no venting is required.
Other
Telephone: The customer must supply a telephone line (with RJ11C modular phone jack) within 3 metres (10 feet)
of the PRINTER to allow remote diagnostic support via modem. A high-grade analog service line is recommended.
Densitometer: An X-Rite DTP-36 densitometer is strongly recommended for calibration of the PRINTER and for
process control.

Printed in U.S.A. •ss2616_1_23nov99.fm
EASTMAN KODAK COMPANY
Rochester, NY 14650
Kodak is a trademark.