Koer C35CBMS User manual

Devices
Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 1 of 6

INTRODUCTION
Learn how to add remote device ID in order to control it from C35CBMS
Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 2 of 6

Step 1 — Enter Advanded Menu
ONLY AUTHORIZED MAINTENANCE PERSONNEL SHOULD ENTER ADVANCED MENU AND
MAKE CHANGES

Picture 1. Press Menu Button

Picture 2. Press Advanced to enter Advanced menu

Picture 3. Enter Admin Password Menu appears

Use the numbers to enter 4 digit factory preset password. Number is being displayed in the blue
ribbon

Press DEL button to delete incorrect number

Press OK to confirm input

Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 3 of 6

Step 2 — Select Submenu
Picture 1. Press Devices button to enter Devices Menu

Picture 2. Shows Devices Menu

Picture 2. Use Home button to return to Home Screen

Picture 2. Use Up button to return to Advanced Menu

Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 4 of 6

Step 3 — Devices settings: Device Address
Under Devices settings, the User can register up to 8, 16, 24 or 32 devices (C35‐FC or C35‐VAV),
depending of the C35‐CBMS device model type. The Devices screen allows 4 devices to be
registered at the time

To register maximum of 8, 16, 24 or 32 devices, navigate with Previous and Next button through
pages

NOTE: In order to operate in defined conditions a C35‐‐FC or C35‐‐VAV device have to be
controlled by just one C35‐‐CBMS device

Device Address: The Device Address (also known as Device ID) is a unique BACnet device
number of a targeted device which can have a value between 1 and 127, inclusive. Please, make
sure that all targeted devices have properly set Device IDs

NOTE: Device ID can be found in Home > Menu > Advanced > Network screen of the
targeted C35 device

To register a C35‐VAV or C35‐FC device within the C35‐CBMS, press the Device Address button
at desired position. A Device ID adjustment screen will open (shown in Picture 2 )

Picture 2. Enter the remote device’s ID and click OK button. Make sure that the entered Device ID
is the same as theDevice ID of the targeted device

If you want to remove registered device just enter 0 as the Device ID

Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 5 of 6

Step 4 — Device Settings: Remote Controlled
Remote controlled: In the Devices
screen, press the Remote Controlled
button next to a Device Address to
activate or deactivate Remote
Controlled feature for that device

When activated, YES text will
appear on the Remote Controlled
button, otherwise the button will be
blank and feature will be disabled
for chosen device. Once a Remote
controlled feature is active, the
device’s working mode can only be
managed through the C35‐CBMS
device

Press Save to confirm changes

Devices Draft: 2017-05-11Guide ID: 83 -
This document was generated on 2019-10-03 01:19:01 PM (MST).
© 2019 products.koer.com/ Page 6 of 6