Kogan KAVTBLST15B User manual

1
1500W Vitablast Blender
KAVTBLST15B
Quick Start Guide
Table of Contents
Safety & Warnings....................................................................................................................................... 2
Operation ..................................................................................................................................................... 3
Cleaning and Care....................................................................................................................................... 5
Specifications ............................................................................................................................................... 5
Troubleshooting ........................................................................................................................................... 5

2
Safety & Warnings
Safety Information
•This appliance is a high-power blender.Please use a separate high-power outlet(>5A) of
high quality. Do not share the outlet with an air conditioner,induction cooker or other
high-power appliance to avoid a fire caused by overcurrent.
•This blender is a Class-I electrical appliance. For the sake of your safety, please ensure
the availability of a good grounding circuit during use of the blender.
•When hot water is used or the work bowl is fully filled,do not exceed the highestscale
mark.
•Make sure the work bowl cover is tightly closed andgradually turn the “Speed Control
Switch” from low to high speed.After operation,take out the processed food carefully to
avoid burns.
•Do not use the work bowl if it is broken or chipped. Check to see if the rotating unit and
the blade are loosened or damaged. When the work bowl has been used for one year or
longer, it is suggested to replace it with an original one of the same specifications.
•When the appliance is running, never use your hand or any other part of your body to
touch the rotating unit, especially the blade. Take care when cleaning or replacing the
blade to avoid cuts and other dangers.
•Do not rinse the appliance directly withwater.Take care not to allow water, soup or any
other liquid to splash into the appliance.
•Do not place the appliance near a gas stove, kerosene stove or gas burner or in an
environment with naked fire or high temperature.
•To avoid possible dangers, ensure only responsible adults of sound mind use the
appliance. Do not allow children or the elderly to use the unit due to increased risk of
injury.
•Do not use the appliance on a carpet, tablecloth or thin paper to avoid blocking the air
suction and exhaust ports, which may affect heat dissipation inside the appliance.
•In order to avoid damage, start the appliance when there is no food in thework bowl.
•During use, take care to protect the appliance from insects, dust and moisture and avoid
short circuiting the unit. If the appliance is to be left unused for a long period,it is
suggested to store it in a plastic bag after cleaning.
•Prior to operation, the unit should stayabout 20cm away from the appliance. To process
liquid food, the appliance must be started at slow speed since impact can be caused by
instant start, which may result in liquid splashing out of the container.
•Put prepared food into the work bowl. The food volume should not exceed the safe scale
mark on the work bowl. Then tightly close the work bowl cover.
•The work bowl uses an open design. When food processing is finished, take out the
processed food as early as possible. If it is impossible to take out it immediately, there
might be slight water seepage at the bottom of the work bowl, which is a normal
phenomenon. Please take out the processed food immediately and clean the work bowl.
•Prior to starting; first confirm that thework bowlis fully connected with thepower
base,and that therubber coveris fully connected with thework bowl. In order to avoid
overflow of food, do not open the work bowl cover during use.
•After use, disconnect the power plug from the outlet to avoid damage to the electronic
components or even caused by long-time conduction.
•If the blender is to be left unused, remember to unplug it from the power outlet.
•Do not open the work bowl cover until the stirring blade comes to a full stop.
•For cleaning, first confirm that the power plug has been disconnected and then separate
the power base from the container.
•Never soak the motor base in water or clean it in a dishwasher.

3
•It is forbidden to start the blender near children; keep a proper distance to prevent
improper movements of children that may give rise to danger.
•Only when the motor has completely stopped are you able to remove the processed food,
otherwise there is a serious risk of injury.
Operation
Preparation
1. Confirm that the operating voltage is 110-120V/60Hz.
2. Confirm that all switches on the blender are in the “OFF” or “0” position.
3. Place the blender on a proper working surface; correctly insert plug into the power outlet.
4. Clean the work bowl, work bowl cover and stirring rod; prepare an appropriate amount of
food for further operation.
Add Food
1. Add food to the work bowl in the following sequence:
•First add soft food and then hard food, followed by liquid food.
•The total amount of food added should not exceed the highest scale mark on the work
bowl; otherwise overflow of food may occur easily during stirring.
•Cut food in to 1-2cm2pieces to make crushing easier and achieve a better effect.
2. Close the work bowl cover and confirm that it is closely mated with the work bowl.Stuff the
small transparent cover into the feed inlet of the rubber cover and turn it to the bayonet
position for fixing. If the stirring rod is needed during stirring, use the stirring rod in place of
the small transparent cover and put it into the feed inlet of the rubber cover.
3. Properly place the work bowl on the power base.
Start the Appliance
1. Prior to operation, the user should keep a safe distance of about 20cm away from the blender.
2. Low speed start: Turn the start switch to the “ON” position, the blender will start at low
speed. After starting, the user can adjust the Speed Control Switch to select an appropriate
speed.
3. Start with pulse switch, turn the pulse switch to the “ON” position, the blender will start at
full speed and the “Speed Control Switch” will not work, if you release the switch, it will
automatically return to the “OFF” position.
4. When food processing is finished, turn all switches to the “OFF” position. When the blender
comes to a full stop, remove the work bowl and take out the processed food.
Operation Skills
1. To process liquid food, the blender must be started at low speed since impact can be caused
by instant start, which may result in liquid splashing out of the container. After the blender
becomes stable, the user can select an appropriate operating speed.
2. Whenfood inside the work bowl does not stir, the pulse switch or the stirring rod can be used.
3. To process food that can foam easily(e.g. tea), the pulse switch for low speed start can be
used, select the number of instant running or operating time according to the amount of foam
desired.
4. When making smooth food, adding an appropriate amount of drinking water can help
operation and reduce difficulty and processing time.
Process Control
1. Time control: Normally, food can be crushed within 30 second.If the desired crushing effect is
not obtained within 30s, then the time can be prolonged to 2 minutes at most.

4
2. Avoid adding food during operation. (do not over-feed the work bowl to avoid overflow or
overload)
3. Stop the blender and add food.
4. When the blender becomes stable, remove the small transparent cover and add an
appropriate amount of food through the feed inlet. (for hot drinks, this operation is forbidden;
the blender must be stopped before operation in order to avoid injury caused by splashes of
hot liquid)
5. When removing the small transparent cover, press the rubber cover to facilitate removal and
prevent the rubber cover from being loosened.
6. Use of stirring rod: Generally, it is used in processing food of poor mobility. During
processing, when food does not stir or cannot move smoothly, the Pulse Switch can be turned
back and forth ~2-3 times.Then use the stirring rod to stir food. During operation, hold the
handle of the stirring rod to stir food up, down, left and right in sequence.
7. The appliance should be in a horizontal position during use and its sides and back should be
at least 20cm away from walls. Do not use the appliance in a narrow space. Take care not to
block the air suction and exhaust ports, which may affect heat dissipation. After use, confirm
that the “Power Switch” is in the “OFF” position.
8. The motor of this appliance is provided with a thermal protection unit.When the temperature
is too high, it will stop automatically. Please power off the appliance and unplug it from the
outlet. You can restart the appliance when the temperature drops to a normal level.
9. If the power cord is damaged, it must be replaced by the manufacturer or a similar
professional.
Star Switch
•The switch is preset to “OFF” before delivery;
•Turn the switch to the “ON” position to start the blender;
•Turn the switch to the “OFF” position to stop the blender.
Pulse Switch
•The switch is preset to “OFF” before delivery;
•Turn the switch to the “ON” position to run the blender at full speed;
•If you release the switch, it will automatically return to the “OFF” position.
Low/High Speed Switch
•The switch is preset to “Low Speed” before delivery;
•Turn the switch to the “Low Speed” position to run the blender at low speed;
•Turn the switch to the “High Speed” position to run the blender at high speed.

5
Cleaning & Care
1. Disconnect the power plug before cleaning the blender.
2. Clean the blender and other components immediately after use.
3. The external part of the power base can be wiped with a wet cloth.
4. After each use,if the blender is to be left idle for more than 10minutes, please clean the work
bowl immediately.
5. After each use, the rubber cover must be removed for cleaning. In order to avoid scratching
the rubber cover, do not use any sharp object for cleaning.
6. Make sure the blender is clean and dry before storage.
7. If the blender is to be left unused for a long period of time, please disconnect the power plug
from the outlet. Take care to protect the blender from dust and insects.
Specifications
Rated voltage
AC120V
Frequency
60Hz
Rated power
1500W
Troubleshooting
Symptom
Possible cause
Solution
Failure to actuate
The power plug is not inserted
Insert the power plug into an
outlet conforming to voltage
requirement
The motor protection unit trips
Place the power base in a
well-ventilated area for about
20 minutes to cool it down
Excessive vibration
The power base is not
balanced
Place the power base on a
horizontal surface
The work bowl is not
completely placed on the
main unit
Properly place the work bowl
on the power base
There is too much food
Adjust the amount of food
Water overflow from the work
bowl cover
The amount of water
exceeds the limit
Adjust the amount of water
The work bowl cover is not
properly positioned
Properly place the work bowl
cover on the work
User manual is subject to change without notice. For the latest version of your user manual, please visit
https://www.kogan.com/usermanuals/