Kogan SMARTERHOME KABLENTLHTA User manual

KOGAN SMARTERHOME™
NIGHT LIGHT
WITH MOTION SENSOR
(KABLENTLHTA)

2
Safety & Warnings
3
Components
4
Overview
5
Installation
7
SmarterHome™ App
9
Operation
16
Specifications
23

3
• Read all instructions carefully before using the product and retain this guide for future
reference.
• The sensing area of this product should not be obstructed or covered by objects.
• When installed, this product should be kept away from direct sunlight and other
sources of heat.
• Do not use this product in humid environments.
• This product is not a toy. Ensure it is kept out of reach of children.
• When charging the product, ensure the voltage of the charger conforms to the
charging voltage of the product (5V 1A). If a charger with improper voltage is used to
charge the product, it may damage the product and cause a potential safety hazard.
• When cleaning the product, wipe it with soft cotton cloth. Do not use any liquid, spray
cleaners or wet clothes when cleaning.
• Do not disassemble, attempt to repair or modify this product in any way.
SAFETY & WARNINGS

4
USB Charging Cable
Hanging Mount
Magnetic Mount
COMPONENTS

5
Top:
Underside:
OVERVIEW
Magnet
Light body
Charging indicator
Sensor
(Light & PIR)

6
Side:
Switch
Charging input
Mounting hole

7
Magnetic Mount
For best results, we recommend that the installation height be greater than 0.4m and less
than 1.2m. The product will still operate but the detection range may be reduced if installed
outside of this range.
Attaching the magnetic mount:
• Clean the surface and ensure it is thoroughly dry before proceeding.
• Remove the adhesive backing from the magnetic mount.
• Adhere the magnetic mount to the cleaned surface and hold it firmly in place for at
least 20 seconds.
Installing the light:
Attach the night light to the magnetic mount, ensuring the magnet is correctly aligned with
the magnetic mount.
INSTALLTION
Notes:
The chosen location must be flat and smooth to ensure a strong bond.
Magnetic mount
Magnet

8
Hanging Mount
• Attach the hanging mount to the mounting hole on the side of the night light.
• The night light can now be safely mounted in a variety of locations: door handles,
clothes hangers, hooks etc.

9
Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification
code sent by SMS.
To R e g i s t e r
1. Ta p t o e n t e r registration page.
2. The system automatically recognises your country/area. You can also select your
country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number' and enter the verification
code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
CONNECT TO SMARTERHOME™ APP

10
Set Device in Pairing Mode
1. Connect the night light to a power supply using the supplied USB cable.
2. Slide the switch to the "MESH" position, the night lamp should now be in pairing
mode.
Notes:
Before connecting the device, please enable Bluetooth on your mobile phone.

11
Bluetooth Connection
This method has a limited range and once the device is outside of the smartphone’s
Bluetooth range, the device will lose its connection and appear offline.
1. Ensure that the device is in pairing mode (switch in “Mesh” position).
2. Open the “Kogan SmarterHome” app.
3. Ensure that Bluetooth is enabled on your smart phone.
4. Tap “+” in the upper right corner of the app’s home page to add a new device
through the network.
5. The app will automatically detect the device, tap “Go to add”.
6. The device will commence the pairing process. Ensure your phone, and the
SmarterHome™ device are kept close until connection is complete.

12
7. During connection, the “ ”flashes continuously in the pop-up window. Please
click "Done" after you have successfully paired the device.
Note: If the networking of the device needs to be reset, please continuously slide
the switch between the “OFF” and “MESH” positions three times. (OFF-MESH-
OFF-MESH-OFF-MESH), with an interval of approximately 2 seconds.

13
Connect the Device Through Gateway
1. Ensure that the device is in pairing mode.
2. Connect your smart phone to your 2.4GHz Wi-Fi network.
3. Open the “Kogan SmarterHome” app.
4. Select “Bluetooth Gateway” from the list of connected devices.
5. Ta p “ s e a r c h n e w d e v i c e ” i n t h e b o t t o m r i g h t c o r n e r o f t h e a p p t o s e a r c h f o r a n y
sub-devices.
6. Ensure that Bluetooth is enabled on your smart phone. If not, you will be prompted
to turn it on.
7. Confirm that the sub-device is in pairing mode then tap “Lights is in a flash” to
begin pairing to the gateway.

14
8. The device will commence the pairing process and connect to the gateway and
app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are
kept close until connection is complete.
9. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.

15
Adding a Connected Device to Gateway
1. Ensure that the device is in pairing mode.
2. Connect your smart phone to your 2.4GHz Wi-Fi network.
3. Ensure that Bluetooth is enabled on your smart phone. If not, you will be prompted
to turn it on.
4. Open the “Kogan SmarterHome” app.
5. Select “Bluetooth Gateway” from the list of connected devices.
6. Ta p “ a d d d e v i c e f r o m l i s t ” i n t h e b o t t o m l e f t c o r n e r o f t h e a p p t o s e a r c h f o r a n y s u b -
devices.
7. Select the device(s) from the list you wish to add to the gateway then tap “confirm”.

16
Power On/Off
To q u i c k l y turn the night light on or off, tap the power icon to the right of the device name.
Settings
Click " " in the upper right corner to view the device information, share the device and
remove device etc.
OPERATION

17
Schedule
1. Ta p o n t h e “ S c h e d u l e” t a b a t t h e b o t t o m r i g h t o f t h e s c r e e n .
2. Ta p o n t h e “A d d S c h e d u l e” button.
3. Choose a start time (on) or end time (off).
4. To setup a repeat on certain days of the week, tap “Repeat” or the schedule will
only occur once.

18
White Adjustment
1. Ta p o n t h e “ W h i t e” t a b a t t h e t o p o f t h e s c r e e n t o e n t e r t h e w h i t e c o n t r o l m e n u .
2. Slide the horizontal bar left or right to set the desired brightness level.

19
Colour Adjustment
1. Ta p o n t h e " C o l o u r ” t a b a t t h e t o p o f t h e s c r e e n .
2. Ta p o n a n y p a r t o f t h e c o l o u r p i c k e r t o s e l e c t a d e s i r e d c o l o u r .
3. Slide the horizontal bars left or right to adjust the colour saturation and brightness.

20
Scene
1. Ta p o n t h e “ S c e n e” t a b a t t h e t o p o f t h e s c r e e n .
2. Ta p o n a n y o f t h e s c e n e i c o n s t o s e l e c t t h e d e s i r e d s c e n e .