Kohler Command PRO CH23 User manual

KOHLER® Command PRO
CH23, CH620-CH740, CH750
CV23, CV620-CV740, CV750
Owner's Manua-1
,,. . ·~·,;.,;
„ll'IPORTANT: · Read all safety precautions a11d ini.trubtions carefully before
operating equipment. Refer to op~rafing instruction of ·.
equipment that this engine powers.
Ensure engine is
stopped and level before performing any
maintenance or service.
Warranty coverage as outlined in the warranty card and on
KohlerEngines.com. Please review carefully as it provides you
specific rights and obligations.
To maintain compliance with applicable emission regulations,
exhaust system backpressure may not exceed limits which can
be found on KohlerEngines.com. Search by Model No., select
Read More, then selectSpecs tab.
3Cord engine information to reference when ordering parts or obtaining warranty coverage.
. EN
ESS '
FRC
1
Engine Model __________________ _
Specification
Serial
Number __________________ _
Purchase
Date __________________ _
1 590 31 Rev. C KnhlP.rFnninA~
~nm

Safety Precautions
A WARNING: A hazard that could result in death, serious injury, or slibstantial property damage.
A CAUTION: A hazard that could result in minor personal injury or property dainage.
NOTE: is used to notify people ofimportant installation, operation, or maintenance information.
Mt
AwARNING
Explosive Fuel
can cause fires. ·
and severe
burns.
"
Do not fill fuel
tank while
engine is hol dr
running.
Gasoline is extremely
flammable and its vapors
can explode ifignited.
Store gasoline only in
approved containers, in
weil ventilated, unoccupied
buildings,
away from sparks
or flames. Spilled fuel
could igni~ if it comes in
contact with hol parts or
sparks from ignition. Never
use gasoline as a cleaning
agent.
AwARNING
lj
Rotating Parts
can cause
severe injury.
Stay away while
engine is in
operation.
Keep hands, feet, hair,
and clothing away from all
moving parts to prevent
injury. Never operate engine
with covers, shrouds, or
guards removed.
AwARNING
Carbon
Monoxide can
cause severe
nausea, fainting
or death.
Avoid inhaling
exhaust fumes.
· Engine exhaust gases
contain poisonous
carbon
monoxide. Carbon
monoxide is odorless,
colorless, and can cause
death if inhaled.
AcAunoN
)t
Electrical Shock
can cause injury.
Do nottouch
wireswhße
engine is
running.
California Proposition 65 Warning
11
AwARNING
Accidental
Starts can cause
~
severe injury or
death.
Disconnect and
~-
ground spark
plug lead(s)
before servicing.
Before working on engine or
equipment, disable engine
as follows: 1) Disconnect
spark plug lead(s). 2)
Disconnec;t negative(-)
battery cable from battery.
AwARNING
s{
Hot Parts can
caus.e severe
b_urns.
Do not touch
engine while
operating or just
after stopping,
" .
lllever operate engine with
heat shields or guards
removed.
Eligine exhaust from this product contains chemicals known
to State of California to cause cancer, birth defects, or other
reproductive
harm.
2
Cal1fornia Proposition 65 Warning
This product contains chemicals known to State of California to
cause cancer, birth defects, or other reproductive harm.
KohlerEngines.com
24 590 31 Rev. C

r-;::=================::::--------7 EN
Dipstick
Oil Fill
Fuel Filter
Oil Cooler Oil Drain Plug Debris .Screen
Dust Ejector
Valve
Heavy-DutyAir
End Cap Element lnnl;lr Element
Cleaner
Air Cleaner lnlet
Screen
Retaining Clip Ejector Area
Housing
Air Cleaner Rubber
Seal
Air Cleaner
. Wing Nut
Knob
Cover
Element Cover Precleaner Paper
Element
Air Cleaner
Base
Low-Profile Air
Oil Fill/Dipstick
Cleaner
re-Start Checklist
·1. Check oil level. Add oil if low. Do not overfill.
:' Check
fuel level. Add fuel if low. Check fuel system components and lines for leaks.
Check and clean cooling areas, air intake areas and external surfaces of engirie (particularly
after storage
).
, Check !hat air cleaner components and all shrouds, equipment covers, and guards are in place
and securely fastened.
5. Check spark arrestor (if equipped).
: t 590 31 Rev. C
KohlerFnninP." r.nm

Starling
AwARNING
Carbon Monoxide can cause
severe nausea, fainting or death.
Avoid inhaling exhaust fumes.
Engine exhaust gases contain poisonous
carbon monoxide. Carbon monoxide is
odorless, colorless, and can cause dealh if
inhaled.
lj
AwARNING
Rotating Parts can cause severe
injury.
Stay away while engine is in
.
operation .
Keep hands, feet, hair, and clothirig away
from all moving parts to prevent injury. Never
operate engine with covers, shrouds, or
guards removed.
NOTE: Do not crank engine continuously for
more than 10 seconds. Allow a 60
second cool down period between
starting attempts. Failure to follow
lhese guidelines
can burn out starter
motor.
NOTE: Upon start-up, ametallic ticking may
occur. Run engine for 5 minutes. lf
noise continues, run engine at mid
lhrottle for 20 minutes. lf noise persists,
take engine to your local Kohler
authorized dealer.
1. Place throttle control midway between slow
and fast positions. Place choke control into
ON position.
2. Turn key switch to START position. Release
switch as soon as engine starts. lf sta rter
does not turn engine over, shut off key switch
immediately. Do not make further attempts to
start engine until condition is corrected. Do
not jump start. See your Kohler authorized
dealer
for trouble analysis.
3. Cold engine: Gradually return chqke control
to OFF position after engine starts and
warms up. Engine/equipment may be
operaled during warm-up period, but it may
be necessary to leave choke partially on until
engine warms up.
Warm engine: return choke to OFF position
as soon as engiile starts.
Cold Weather Starling Hints
1. Use proper oil for temperature expected.
2. Disengage all possible external loads.
3. Use fresh winter grade fuel. Winter grade
fuel has higher volatility to improve starting.
Stopping
1. lf possible, remove load by disengaging all
PTO driven attachments.
2. Position throttle control between half and full
throttle; stop engine.
Angle of Operation
Refer to operating instructions of equipment
this engine powers. Do not operate this engine
exceeding maximum angle of operation; see
specification table. Engine damage could result
from insufficient lubrication.
Engine Speed
NOTE: Do not tamper with governor setting to
increase maximum engine speed. ·
Overspeed is hazardous and will void
warranty.
Cold Weather Operation
Anti-icing kits can be installed to irnprove cold
wealher operation and are available through
your local Kohler authorized dealer.
High Alt1tude Operation
This engine may require a high altitude
carburetor kit to ensure correct engine
operation ataltitudes above 4000 fl.
(1219 meters). To obtain high altitude kit
information or to find a Kohler authorized dealer ·
visit
KohlerEngines.com or call 1-800-544-2444 / ,
(U.S. and Canada). · .. ,
This
engine should be operated in its original
configuration below 4000 ft. (1219 meters)'as / '
damage may occur if high altitude carburetor kil· i
is installed and operated below 4000 fl. (1219 -·
1
meters). · u
u
' '
i i
4 KohlerEngines.com
24 590 31 Rev. C

Maintenance lnstructions
1
11
AwARNING
Before working on engine or equipment, disable
~
Accidental Starts can cause engine
as follows: 1) Disconnect spark plug
severe injury or death.
lead(s). 2) Disconnect negative(-) battery cable
~
.Disconnect and ground spark
from battery.
plug lead(s) before servicing.
Normal maintenance, replacement:onepair ofemission control devices and systems may be
rierformed by any repair establishment or individual; however, warranty repairs must be performed
1y a Kahler authorized dealer found at KohlerEngines.com or 1-800-544-2444 (U.S. and Canada).
• Replace low-profile air cleaner element.
• Change oil.
• Remove cooling shrouds and clean cooling areas.
•
Chec!< oil cooler fins, cle~n as necessary (ifequipped).
• Have crankshaft spline lubricated.
1
1
Perform these procedures more frequently under severe, dusty, dirty conditions.
2
Have a Kahler authorized dealet perform this service. .
11 Recommendat,ons
••re recommend use ofKahler oils for best
3rformance. Other high-quality detergent
uds (including synthetic) of API (American
Petroleum Institute) service class SJ or higher
·e acceptable. Select viscosity based on air
mperature at time ofoperation
as shown in
table below.
Check Oll Level
NOTE: . To prevent extensive engine wear or
damage, never run engine with oil level
below or above operating range
indicator on dipstick. ·
Ensure engine
is cool. Clean oil fill/dipstick
areas of
any debris.
1. Remove dipstick; wipe oil off.
a. Press-in cap: reinsert dipstick into tube;
press completely down.
or
b. Thread-on cap: reinsert dipstick into
tube; rest cap on tube, do not thread cap
onto tube.
2. Remove dipstick; check oil level. Level
should be at top of indicator on dipstick.
3. lf oil is low on indicator, add oil up to top of
indicator mark.
4. Reinstall dipstick and tighten securely.
EN

Change Oil ancl Filter
Change oil while engine is warm.
1. Clean area around oil fill cap/dipstick, drain
plug/oil drain valve.
a. Remove drain plug and oil fill cap/
dipstick. Allow oil to drain completely.
or
b. Open oil drain valve cap; if needed
attach a length of 1/2 in. I.D. hose t'o
direct oil into appropriate conlainer; twist
valve drain body counterclockwise and
pull. Remove dipstick. Allow oil to drain
completely.
2. Clean area around oil filter. Place a container
underfilter to
catch any oil and remove filter.
Wipe off moµnting surface.
a. Reinstall drain plug. Torque to 1Olt. lb.
(13.6 N·m). or
b. Close oil draln valve body, remove hose
(II used), and replace cap.
3. Place new filter in shallow pan with open end
up. Fill wlth new oil until oll reaches bottom
of threads. Allow 2 mlnutes for oll to be
· absorbed by filter material.
4. Apply a thin film of clean oil to rubber gasket
on new filter. ·
5. Refer to instructlons on oil filter for proper
installation.
6. Fill crankcase with new oil. Level should be
at top of indicator on dipstick.
7. Reinstall oil 1111 cap/dipstick and tighten
securely. ·
8. Start engine; check for oil leaks. Stop engine;
correct leaks. Recheck oil level.
9. Dispose of used oil and filter in accordance
with local ordinances.
Oil Sentry, (if equipped)
This switch is designed to prevent engine
from starting in a low oil or no oil condition. Oil
Sentry ™ may not shut down a running engine
before damage occurs. In some applications
this switch may activate a warning siglial. Read
your equipment manuals for more information.
Fuel Recommendat1ons
*
AwARNING
Explosive Fuel can cause fires
"
and severe bums.
Do not fill fuel tank while engine is
hot or running.
Gasoline is extremely flammable and
its vapors can explode if ignlted. Store
gasoline only in approved containers, in
weil ventilated, unoccupied buildings, away
from sparks or flames. Spilled fuel could
ignite lf it comes in conlact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent. ·
NOTE: E15, E20 and E85 are NOT approved
and should NOT be used; effects of
old, stale or contamlnated fuel are not
warrantable.
Fuel must meet these requlrements:
• Clean, fresh, unleaded gasoline.
• Octane rating of 87 (R+M)/2 or higher.
• Research Octane Number (RON) 90 octane
minimum. ·
•
Gasoline up to 10% ethyl alcohol, 90%
unleaded is acceptable.
• Methyl Tertiary Butyl Ether (MTBE) and
un(eaded gasoline blend (max 15% MTBE by
volume) are approved.
• Do not add oil to gasoline.
• Do not overfill fuel tank.
• Do not use gasoline older than 30 days.
Fuel L1ne
Low permeatlon fuel line must be installed on
carbureted Kahler Co. engines to malntain EPA
and CARB regulatory compliance.
6 KohlerEngines.com
24 590 31 Rev. C
f
1'

Spark Plugs
AcAUTION
Electrical Shock can cause injury.
Do not touch wires while engine
is runhing.
< 3an out spark plug recess. Remove plug and
replace.
1 Check gap using wire feeler gauge. Adjust
gap, see specification table for adjustment.
2. lnstall plug ir:ifö cylinder head.
forque plug to 20 ft. lb. (27 N·m).
ir Cleaner
1\ ITE: Operating engine with loose or
damaged air cleaner components
could cause
premature wear and
failure. Replace all bent or damaged
components.
IIOTE: Paper element cannot be blown out
with compressed
air.
.ow-Profile/Commercial Mower
.r 1sen knob and remove air cleaner cover.
~l - cleaner:
. Remove precleaner from paper element.
!. leplace orwash precleaner in warm water
with detergent.
Rinse and allow to air dry.
:. '";aturate precleaner with new engine oil;
queeze out excess oil.
•· Reinstall precleaner over paper element.
11
,er Element:
. ..;1ean area around element. Remove wing
nut, element cover, and paper element with
recleaner.
. ,:,eparate precleaner from element; service
precleaner
and replace paper element.
. :heck condition of rubber seal' and replace if
,
,ecessary.
• 1 '1stall new paper element on base; install
redeaner over paper
element; reinstall
vlement cover
and secure with wing nut.
eiristall air cleaner cover and secure with
1 ).
eavy-Duty
··nhook retaining clips and remove end
lp(s).
Check
and clean inlet screen (ifequipped).
~II air cleaner element out of housing and
. .1place. Check condition of inner element;
replace when dirty.
4. Check all parts for wear, cracks, or damage, EN
and that ejector area is clean.
5. lnstall new element(s).
6. Reinstall end cap(s) with dust ejector valve/
screen down; secure with retaining clips. _
Br eather Tube
Ensure both ends of breather tube are properly
connected.
011 Cooler (1f equ1pped)
1. Clean fins with a brush or compressed air.
2. Remove two screws securing oil cooler, and
tilt to clean back side.
3. Reinstall oil cooler.
Arr Cool111g
AwARNING
sl
Hot Parts can cause severe
bums.
Do not touch engine while
operating orjust after stopping .
Neveroperate
engine with heat shields or
guardstemqved.
Proper
cooling is essential. To prevent over
heating, clean screens, cooling fins, and other
external surfaces of engine. Avoid spraying
water at wiring harness or any electrical -
components.
See Maintenance Schedule.
Repa1rs/Service Parts
We recommend !hat you use a Koh(er
authorized dealer for all maintenance,
service, and replacement parts for engine.
To find a Kohler authorized dealer visit
KohlerEngines.com orcall 1-800-544-2444
(U.S. and Canada) .
Storage
lf engine will be out ofservice for 2 months or
more follow procedure below.
1. Add Kohler PRO Series fuel treatment or
equivalent to fuel tank. Run engine 2-3
minutes to get stabilized fuel into fuel system
(failures due to untreated fuel are not
warrantable ).
2. Change oil while engine is still warm from
operation. Remove spark plug(s) and pour
about 1 oz. of engine oil into cylinder(s).
Replace spark plug(s) and crank engine
slowly to distribute oil.
3. Disconnect negative(-) battery cable .
4. Store engine in a clean, dry place.
i ,90 31 Rev C KohlP.rl=nnin,::ac::
r-nm

Troubleshoot1ng
Do not attempt to service or replace major engine components, or any items that require speclal
timing or adjustment procedures. This werk should be performed by a Kahler authorized dealer.
Dirt In Dirty
lmproper
Fuel
Debris lncorrect Engine
Screen Oil Level Overloaded
Dirty Air
Cleaner
Fuel Une
Will Not Start
• • • • • • •
Hard Starling • • • • • •
Stops Suddenly
• • • • • • •
Lacks Power
• • • • • • •
Operates Erratically . • • • • • •
Knacks or Pings
• • • •
Skips or Misfires • • • • •
Backfires • • • • •
Overheats • • • • • •
High Fuel
• • •
Consumption
Engine Specifications ·~
1--
Bore 1
Model Strake I
~···~~:,1~- Maximum Angle
. Oil Capacity Spark of Operation
;D1s placement (Refill) IPlug Gap (@ full oil level)*
CH621
CV621
3.03 in. 38.1 CU. in.
CH641
(77mm) (624 CC)
CV641
CH620
CV620
CH640
CV640
3.2in. 2.6in. 41 CU. in.
CH23/CH680
(80mm)
(67 mm)
(674 ce)
1.7-1.9 u.s. qt
0.03 in.
CH670
(1.6-1.8 L)
(0.76 mm)
25°
CV23/CV680
CV670
CH730
CV730
44.2 CU. in.
CH740
3.27in.
(725 cc)
CV740
(83mm)
CH750
2.72in. 45.6cu. in.
CV750
(69 mm) (747 cc)
*Exceeding maximum angle·of operation may cause engine damage from insufficient lubrication.
Additional specification information can be found in service manual at KohlerEngines.com.
Exhaust Emission Control System for models CH23, CV23, CH620-CH740, CV620-CV740,
CH750, and CV750 is EM for U.S. EPA, California, and Europe.
Any and all horsepower (hp) references by Kahler are Certified Power Ratings and per SAE J1940
& J1995 hp standards. Details on Certified Power Ratings can be found at KohlerEngines.com. '
8 KohlerEngines.com
24 590 31 Rev. C
r~
ri

Limited Warranty • Kohler Engines
Kahler Co. warrants to the original retail purchaser that each new engine will be free of manufacturing defects in materials and
workmanship for the applicable coverage period set forth below, beglnning on the date of purchase; provided the engine is operated
and maintained in accordance with Kahler Co.'s instructions and nianuals.
Type of Use .
U.S.A. Emission
Englne Series
Residential
Commercial
Refer to Seclion
Aegis®
3 Years
3 Years
Bore
Command PRO®
3 _Years
3 Years
BorC
Command PRO
0
CS
2 Years
2 Years A
Command PRO® EFI
3 Ye~_rs
3 Years
Bore
Command PRO® (Single Cylinder) 3
Years
3 Years B
Courage®
2 Years
90 days A
Courage PRO. 2
Year:s
1 Year A
Confidant. 3
Years
2 Years
B
· XTSeries. 2
Years
90 days A
2000 Series. 2
Years
90 days A
3000 Series. 2
Years
90 days A
7000 Series. 2
Years
90 days A
K-Series. 1
Year
1 Year N/A
Magnum. 2
Years
2Years
N/A
OHC/Triad® 2 Years 2Years
N/A
Kahler Co.'s obligation underthis warranty is expressly limited, at its. ppti_on, to an appropriate adjustment, repair, or replacement of
such part or parts as found tobe defective following an inspection by/Kohler Co. or an authorized servioe facility designated by Kohler
~- !
LIMITATIONS: ,. . . .
Mufflers on engines used commercially (non-residential) ane warrant~d'.for one (1) year from date of purchase, except catalytic ni~!llers,
which are warranted for two (2) years. ·- :. , .
EXCLUSIONS: ,
The following items are not covened by this warranty.- .!
• Damage caused by: (i) an accident or casualty; (ii) unreasonable t/~e or neglect; (iii) normal wear; (iv) premature wear fnom improper
maintenance; (v) impnoper storage; (vi) old or contaminated fuel leffwithin the fuel system, which includes but is not limited to tanks,
fuel lines, carburetors or fuel injection components.
• Failures caused by: (i) faulty repairs made by any party othertlian Kphler Co. or an authorized service facility·designated-.by Kobler
Co.; (ii) use of non-Kahler replaoement service parts; or (iii) an act qeyond the control of Kohler Co., which includes but is not limited to
thefl, vandaUsm, flne, lightning, earthquake, windstorm, hail, volcanic eruption, flood or tornado.
• Transportation charges in connection with lhe repalr orreplacement of defective parts.
• Engine accessories such as fuel tanks, clutches, transmissions, power drive assemblles, and batteries, unless supplied or installed by
Kahler Co.
1;\
• Rental of equipment during performance of warranty repairs. ,
•
Fuel, lubricating eil, air filters, eil filters, spark plugs or coolant/antlfr~eze.
IMPLIED OR STATUTORY WARRANTIES, INCLUDING THOSE OF [MERCHANTABILITY AND FITNESS FORA PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF Tl:US WRITTEN WARRANTY. KOHLERCO. MAKES NO OTHER
EXPRESS WARRANTY, NOR IS ANYONE AUTHORIZED TO MAKE,ANY ON KOHLER CO.'S BEHALF. KOHLER CO. AND/OR THE
SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDtNTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND.
'
Some states or countries do not allow limitations on how long an implied warranly lasts, or the exclusion or limitation of incidenlal or
consequential damages, so the above limitation or exclusion may notapply_ to you. This warranty gives you specilic legal rights, and
you may also have other rights which vary from country to country (www.KohlerEngines.com), or state to state within U.S.A.
TO OBTAIN WARRANTY SERVICE:
Original retail purchaser must bring the engine to an authorlzed serviqe facility designated by Kahler Co. found by visiting www.
KohlerEngines.com or telephone [phone] (U.S.A. and Canada).
ENGINE DIVISION, Kahler Co., Kohler Wisconsin
25 590 20 Rev. A
KohlerEngines.com
KOHLER.

Eingeschränkte Gewährleistung • Kohler Motoren
Die Kahler Co. garantiert dem Erstkäufer, dass der von ihm erworbene Motor frei von Herstellungs- und Materialfehlern ist. Diese
Garantie gilt ab dem Kaufdatum für den nachstehend genannten Zeitraum, unter der Voraussetzung, dass der Motor entsprechend den
Anweisungen und technischen Unterlagen der Kahler Co. betrieben und gewartet wurde.
Art des Gebrauchs USA
Abgasstufe
Motorbaureihe Nicht Gewerbliche Siehe
gewerbliche
Nutzung Nutzung Abschnitt
Aegis®
3 Jahre
3Jahre Boder C
Command PRO
0 3
Jahre
3Jahre Boder C
Command PRO
0
CS 2 Jahre
2Jahre A
Command PRO
0
EFI 3 Jahre
3Jahre Boder C
Command PRO
0 (Einzylinder) 3
Jahre
3Jahre B
Courage. 2
Jahre
90 Tage
A
Courage PRO. 2
Jahre
1 Jahr A
Confidant™
3 Jahre
2Jahre B
XTSeries™ 2
Jahre
90 Tage A
2000 Series™
2 Jahre
90 Tage A
3000 Series™
2 Jahre
90 Tage A
7000 Series™
2 Jahre
90 Tage
A
K~Series®
1Jahr 1 Jahr
n.zutr.
Magnum®
2 Jahre 2Jahre
n.zutr.
OHC/Triad
0 2
Jahre
2Jahre
n.zutr.
Die Verpflichtung der Kahler Co. im Rahmen dieser Gewährleistung sind ausdrücklich unq im Ermessen des Herstellers auf die
Wandlung oder Reparatur von Komponenten oder Baugruppen beschränkt, die bei einer Überprüfung durch die Kahler Co. oder ein
von ihr autorisiertes Servicezentrum offensichtliche Mängel aufweisen.
GARANTIEEINSCHRANKUNGEN:
Für die Schalldämpfer gewerblich genutzter Motoren gilt eine Garantie von einem (1) Jahr ab dem Kaufdatum. Ausgenommen von
dieser Regelung sind Abgasschalldämpfer mit Katalysator, für die eine Garantie von zwei (2) Jahren gilt.
AUSNAHMEN:
Folgende Leistungen bzw. Komponenten sind nicht durch diese Garantie gedeckt:
• Schäden durch: (i) Unfall oder höhere Gewalt; (ii) unsachgemäßen Gebrauch oder Fahrlässigkeit; (iii) normalen Verschleiß; (iv)
vorzeitigen
Verschleiß durch eine nicht vorschriftsgemäße Wartung; (v) falsche Lagerung; (vi) alten oder verschmutzten Kraftstoff in
der Kraftstoffanlage, einschließlich Tanks, Kraftstoffleitungen, Vergaser und Komponenten derKraftstoffeinspritzung.
•Funktionsstörungen
aufgrund: (u) fehlerhafter Reparaturen, die von Dritten und nicht von der Kahler Co. oder einem von Kahler
autorisierten Kundendienst vorgenommen wurden; (ii) der Nichtverwendung von Kahler-Originalersatzteilen; oder (iii) eines
·Ereignisses außerhalb der Kontrolle der Kahler Co., wie beispielsweise Diebstahl, Vandalismus, Brand, Blitzschlag, Erdbeben, Sturm,
Hagel, Vulkanausbruch, Hochwasser oder Tornados.
•Transportkosten, die für eine Reparatur oder Auswechslung von Schadenstellen anfallen.
•Motorbauteile wie Kraftstofftanks, Kupplungen, Getriebe, Antriebskomponenten und Batterien, die nicht von der Kahler Co. geliefert
oder eingebaut wurden.
• Die Vermietung von Geräten während Garantiereparaturen.
•Kraftstoff, Schmieröl, Luftfilter, Ölfilter, Zündkerzen oder Kühlmittel/Frostschutzmittel.Kraftstoff, Schmieröl, Luftfilter, Ölfilter,
Zündkerzen oder Kühlmittel/Frostschutzmittel.
SÄMTLICHE AUSDRÜCKLICHEN ODER STILLSCHWEIGENDEN ZUSAGEN EINSCHLIESSLICH DER MARKTGÄNGIGKEIT UND
EIGNUNG FÜR EINEN SPEZIFISCHEN VERWENDUNGSZWECK SIND AUSDRÜCKLICH AUF DEN GÜLTIGKEITSZEITRAUM
DIESER SCHRIFTLICHEN GARANTIE BESCHRÄNKT. DIE KOHLER eo. GEWÄHRT KEINE WEITEREN AUSDRÜCKLICHEN
GARANTIEN, NOCH HAT SIE IRGENDJEMANDEN AUTORISIERT, IRGENDWELCHE ZUSICHERUNGEN IM NAMEN DER KOHLER
eo. zu GEWÄHREN. DIE KOHLER CO. UND/ODER DEREN VERTRIEBSPARTNER HAFTEN NICHT FÜR SPEZIFISCHE,
INDIREKTE, NEBEN- ODER FOLGESCHÄDEN.
In einigen Ländern sind Einschränkungen der Dauer einer stillschweigenden Zusicherung und der Ausschluss oder die Limitierung
von Neben- und Folgeschäden nicht zulässig, daher gilt die oben genannte Beschränkung in Ihrem Land eventuell nicht. Diese
Gewährleistung räumt Ihnen bestimmte Rechte ein und besteht zusätzlich zu allen anderen Rechtsansprüchen, die Sie möglicherweise
haben und die je nach Land (www.KohlerEngines.com) bzw. Bundesstaat der USA unterschiedlich ausfallen können.
NUTZUNG DES GARANTIEANSPRUCHS:
Als privater Erstkäufer müssen Sie den Motor zu einem autorisierten Kahler-Vertriebspartner bringen; entsprechende Adressen finden
Sie auf www.KohlerEngines.com oder können Sie telefonisch unter der Rufnummer 1-800-544-2444 (USA und Canada) anfragen.
ENGi NE DIVISION, Kahler Co., Kahler Wisconsin
25 590 20 Rev. A
KohlerEngines.com
5