Kohler LOURE 98337T-C User manual

1268045-2A-A 1
BEFORE YOU BEGIN
1268045-2A-A 4
INSTALLATION INSTRUCTIONS
98337T-C 6219T-C Shower Column
LOURE
98337T-C 6219T-C Shower Column
LOURE
ROUGH-IN DIMENSIONS
HANDLE OPERATION
SERVICE PARTS
**Color code must be specified when ordering
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Shut off the water supplies to the fitting.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. Recommended minimum working pressure is 0.2MPa(2bar).
5. The highest working pressure for shower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60ºC. Please keep showerhead, handshower and
shower arm away from heater, or it may become damaged and cause injury to the user.
Turn the diverter handle upwards to the side with handshower logo, the handshower will work; turn it upwards
to the side without any logo, both showerhead and handshower will work; turn it upwards to the side with
showerhead logo, the showerhead will work.
1500±20
G1/2˝
G1/2˝
65
380
98337T-C: 938
6219T-C: 934
Recommended
Height
1000~1100
G1/2˝
1023
850±3
Finished Floor
G1/2˝
430
126
98337T-C: 384×384
6219T-C: 254×254
G1/2˝
2824
9220
1109613
1173737
1148976**
1137478**
3013706
1162076**
833548
42045
1167535**
3013706
1148979**
1248781**
1101257**
3010849
833730
1153546**
1158490
1148983**
1109469
1092935
1082904
3010643
1159770
42045
3013706
98337T-C:1260900**
1030624
77420
6219T-C:1261848**
1030624
77420
79680
85549

1268045-2A-A 2 1268045-2A-A 3
INSTALLATION
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION CHEKOUT
Ensure that all connections are tight.
Turn on the drain and main water supply, and check for leaks. Repair as needed.
How to Install the Shower Column
Select a location in vertical wall to install shower column according to
rough-in dimensions.
To perform installation, installer must provide G1/2˝ female supply
fitting(1).
NOTE: The supply fitting should be not beyond and below the finished
wall less than 7mm, be vertical as well.
Loosen the screw(3) with the hex wrench(2), and remove the diverter
kit(4). Apply tape or thread sealant to the diverter threads. Thread the
diverter kit onto G1/2˝ supply fitting until against the finished wall, adjust
diverter kit and make sure the connector(5) facing upwards.
Rehearse the slide bar kit(6) installation for the anchor(7) mounting
location determination. Install the slide bar kit onto the diverter kit by the
pin(8). Place the base(9) against the finished wall. Mark the square
outline of the bottom of the base with a pencil on the wall. Remove the
cap(10). Unscrew the screw(12) with the hex wrench(11)(NOTE: Don't
lose the screw.), and remove the base. Mark the center point of the
square outline with a pencil.
Drill a hole on the center point as the anchor diameter. Press the
anchor into the hole. Secure the base by the self-tapping screw(13) with
the washer(14), and make sure the slot of the base upwards, and the
bottom of the base coincides with the square outline on the wall.
Slide the slide bar kit onto the base, and connect the slide bar kit and
the diverter kit by the pin. Tighten the screw(3) with the hex wrench(2).
Install the screw(12) with the hex wrench(11) and tighten it to secure
the slide bar kit. Adjust the base vertically to install the screw, if needed.
Install the cap.
7
3
44mm
Center Point
Square Outline
44mm
2
4
5
6
8
10
11
12
13
14
9
1
16
15
17
18
19
How to Install the Showerhead
Turn the diverter handle(16) upwards to the side with showerhead logo
and run hot and cold water for about one minute to remove any debris
before the showerhead(15) is installed.
Tighten the showerhead onto the outlet(17) with strap wrench.
Before installation, install the restrictor(18) if needed. Take out the
washer(19) and install the restrictor as the figure shown, reinstall the
washer.
How to Install the Handshower and Hose
Turn the diverter handle(16) upwards to the side with handshower logo
and run hot and cold water for about one minute to remove any debris
before the handshower(20) is installed.
If needed, install the restrictor(21) and spring washer(22) into the inlet of
the handshower according to installation instruction. Connect the end A
of the hose(23) to the connector(24). Connect the end B of the hose to
the handshower.
20
21
22
23
24
A
B