Kohler 8881T-VC01-BN User manual

18 E 201206 2012
2012
PSD
PSD URINAL SENSOR W/PSD TECHNOLOGY
INSTALLATION INSTRUCTIONS
8881T-VC01-BN/AF(0.5L&1L可调式/DC/ )
8881T-VC03-BN/AF(0.5L&1L可调式/AC/ )
8881T-UC01-BN/AF(3L/DC/ )
8881T-UC03-BN/AF(3L/AC/ )
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is base upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-please leave instructions for the
consumer.
Open end/adjustable wrenches
Tape measure
Basin Wrench
Pipe wrench
Square
Level
Pliers
Socket wrench with sockets
Screw driver
Seal tape
安装之前
BEFORE YOU BEGIN
REQUIRED TOOLS AND MATERIALS 所需工具及材料
请仔细阅读本说明书，以便了解所需工具、材料及安装
程序。请遵照相关章节进行安装，以避免由于安装不当
而导致不必要的损失。除了有关部门正确的安装方法之
外，还务请阅读所有操作安全说明。
本说明书所含一切材料，均以印刷时所有的最新产品为
准。科勒中国公司保留随时更改产品特性、包装或供应
情况的权利，恕不另行通知。
本说明书也包含了有关护理、清洁及保养等重要资料－
请交予用户保存。
开口/活动板钳
卷尺
梅花板钳
管扳手
直角尺
水平尺
老虎钳
管钳子
十字螺丝刀
生料带
小便器感应器
1206437-T01-A

Flushing mode
2 " AA" size alkaline batteries
Model
Power
Liter per flushing
Temperature Environmental temperature: 1 to 55
Starting pressure 0.05~1.0MPa
Sensing distance About 60cm away from sensing window
Testing time About 2 seconds to 5 seconds
0.05~1.0MPa
Flushing after used (0.5L)
Sensing technology PSD ( Position Sensitive Device)
8881T-VC01-BN/AF(0.5L/DC)
8881T-VC03-BN/AF(0.5L/AC)
When water pressure is 0.18~0.55MPa.,
average flushing is no more than 1L
When water pressure is 0.10MPa.,
no more than 1L
0.18~0.55MPa.
1L
0.1MPa 1L
8881T-VC01-BN/AF(1L/DC)
8881T-VC03-BN/AF(1L/AC)
0.18 0.55MPa
0.5L
0.1MPa 0.5L
Water pressure at 0.18~0.55 MPa:
average flushing is no more than 0.5L
Water pressure at 0.1 MPa:
no more than 0.5L
SENSOR SPECIFICATION 感应器规格
8881T-VC01-BN/AF(1L/直流型)
8881T-VC03-BN/AF(1L/交流型)
8881T-VC01-BN/AF(0.5L/直流型)
8881T-VC03-BN/AF(0.5L/交流型)
冲洗方式
感应技术 光电位置敏感探测技术
型 号
电 源
冲洗水量
使用温度
启动压力
感应范围
检测时间
使用后冲洗(0.5L)
约2秒至5秒
距感应窗口约60cm
2节5号碱性电池（AA x 2）
环境温度：1～55℃
8881T-UC01-BN/AF(3L/DC)
8881T-UC03-BN/AF(3L/AC)
8881T-UC01-BN/AF(3L/直流型)
8881T-UC03-BN/AF(3L/交流型)
220V AC 50/60Hz
Water pressure at 0.18~0.55 MPa:
average flushing is no more than 3L
Water pressure at 0.1 MPa:
no more than 3L
0.18 0.55MPa
3L
0.1MPa 3L
220V AC 50/60Hz
Dual flushing (1L/3L) 两段冲洗(1L/3L)
2
1206437-T01-A

1100331-SP-BN 1196535-SP-AF 1115769-SP 16306T-NA
8881T-VC01-BN
8881T-VC03-BN
8881T-UC01-BN
8881T-UC03-BN
8881T-VC01-AF
8881T-VC03-AF
8881T-UC01-AF
8881T-UC03-AF
8881T-VC01-BN
8881T-VC01-AF
8881T-UC01-BN
8881T-UC01-AF
8881T-VC03-BN
8881T-VC03-AF
8881T-UC03-BN
8881T-UC03-AF
PRODUCT PAGE 产品图
Slurry Mold
灰浆模套
Flushing Control Stick
冲洗控制棒 Hex Pan
2.5mm内六角扳手
1100331-SP-BN
1196535-SP-AF
Panel
面板 1092297-SP
Senosor Lens
透明条
Gasket
垫圈
1205586-SP
1205587-SP
Electronic Unit Assy.
电控盒组件
Control
box bracket
电控盒支架
1115769-SP
Battery Box,Assy
电池盒组件
Valve Body
主体
Inlet Connection
进水接头
Anti-Rotating Sheet
防转片
Nut
螺母
Gasket
橡胶垫圈
Screw M4X50
螺钉 M4X50
Screw, M3X8
螺钉 M3X8
1100691-SP
Assy, Filter
滤网组件
O-ring
O型圈
1088695-SP
Valver Cover
阀盖 O-ring
O型圈 1056081-SP
Solenoid Valve
电磁阀
ACL-219G202-SP
Pressing Board
压片
1100658-SP
Bracket Assy
固定架底板组件
Screw M3X8
螺钉M3X8
O-ring
O型圈
Valve Cover
止水阀盖
Pressing Board
压片
Screw M3X8
螺钉 M3X8
Screw M2.5X6
螺丝 M2.5X6
Screw M3X12
螺钉 M3X12
Screw M3X22
螺钉 M3X22
Lock Nut
吊紧螺母
Valve Box
暗盒
1100693-SP
Diaphragms Assy
膜片组件
Adjustment Bolt Assy
调节螺栓组件
Connector
连接件
Outlet Connection
出水接头
Screw M3X8
螺钉M3X8
Restrictor
节流器
O-ring
O型圈
Valve Body Assy
主体组件
O-ring
O型圈
16306T-NA
AC交流电源盒
1145332-SP
Connector
接插件组件
1205586-SP
8881T-VC01-BN
8881T-VC01-AF
8881T-VC03-BN
8881T-VC03-AF
1205587-SP
8881T-UC01-BN
8881T-UC01-AF
8881T-UC03-BN
8881T-UC03-AF
1206437-T01-A
3

UNIT：mm
单位：毫米
K-4904T-ER K-4904T-ET
420±40
370
K-4986T-ER
83 126
149
320±40
523
83 126
149
320±40
150
83 126
149
K-5016T-YER K-5016T-YET
320±40
486
83 126
149
150
83 126
149
358
320±40
486 358
83 126
149
K-18645T-Y-0
420±40
455
K-4960T-ETK-4960T-ER
320±40
523
83 126
149
320±40
150
83 126
149
ROUGHING-IN 尺寸图
4
1206437-T01-A

8881T-VC01
8881T-VC03
K-4904T-ER、K-4904T-ET、K-4986T-ER、K-5016T-YER、
K-5016T-YET、K-18645T-Y-0
8881T-UC01
8881T-UC03
K-4960T-ER、K-4960T-ET、K-18645T-Y-0、K-5016T-YER、K-5016T-YET
K-4978T-ER、K-4978T-ET
≈
320±40
≈
150
K-4978T-ET
523
≈
320±40
K-4978T-ER
126
149
83 83 126
149
523
Note: 注意：
a. 以上尺寸仅供参考。
b. 出水配件需另行选配。
上进水配管选配K-2464T-NA,后进水配管请选用不
锈钢编织软管。
c. 为保证有效冲洗，需配相应冲量要求的小便斗，小
便斗本身需符合ASME A112.19.2-2003要求，不推荐
用虹吸式小便斗。
d.为了保证您能放心使用感应器，当配后进水小便器
时，建议用户自行选配内径不小于9mm的不锈钢编织
软管，其接口尺寸分别如图所示。
e.为保证有效冲洗，推荐供水管路（包括水表、阀等）
内径不小于25mm，推荐供水水压（冲洗器进水口流动
水压）：0.18MPa～0.55MPa。
a. The dimensions above are just for reference.
b. The connection take between the outlet connection
and urinal is not supplied in this package.
Please use K-2464T-NA as top inlet, use stainless
steel hose as rear inlet
c. To ensure an effective flush performance, an urinal
with corresponding flush volume is required. And
the urinal should comply with ASME A112.19.2-2003.
Siphon urinal is not recommended.
d. To insure you can use the sensor with ease, when
used with rear inlet urinal, recommended inner diameter
of stainless steel hose chose by customer is no less
than 9mm.The connection dimensions are shown in the
figures.
e. TO ensure an effective flush performance strongly
recommended inner diameter of water supply (including
water meter, valve, etc.) is no less than 25mm, and
supplied water pressure(sensor inlet dynamic pressure)
is 0.18Mpa~0.55Mpa.
1206437-T01-A
5

1 . Determine the installation location per rough-in dimensions.
Chisel out a slot and install the supply tubing . Turn off the
water supply. The depth of the slot is no less than 90mm,
see the figure right for rough-in dimension requirement.
NOTE:
Installation location: No strong ultraviolet radiation or
electromagnetic field nearby.
2 . Put the flush valve into the slot. Then connect the water
supply and make the outlet aligned with the center of the
urinal stall. Secure the flush valve with supporting block to
make it flat and straight. Then connect the inlet pipe .
According to the dimensions of the urinal stall, the outlet
fitting are connected and installed as shown in the
rough-in. (See “ROUGHING-IN”)
NOTE:
a. Don’t mistake the direction of inlet and outlet.
b. Please clean the inside of water supply pipe before
connecting to the product.
INSTALLATION 安装步骤
1.根据安装尺寸图确定安装位置，凿出槽坑，埋设供水管，
暂不供水。（槽深不小于90mm），尺寸参考右图。
安装交流型时，添加右图虚线内槽坑用于安装电工套管。
注意：安装位置:
a. 不能靠近强烈紫外线或电磁场。
b. 不能有光源直射或反射进感应窗口。
c. 不能在感应器正对面有易反射的物品（如镜子、
光亮不锈钢板及其他镜面物体）。
Nut
Outlet Connection
Water Supply (Recommended Inner
Diameter Is More Than 25mm)
Battens
垫紧块
出水连接 螺母
供水管（推荐内径大于25mm）
Installation Site
90
安装区
90
90
75
Install bushing
适合安装
电工套管
≈28
≥90
Connect control box while
installing AC
安装交流型时接面板上的电控盒
Outer diameter of Bushing
is No More Than 25mm
电工套管外径≤25mm
AC Power Unit
交流电源盒
2.将冲洗阀放入槽坑内，然后连接进水口，出水口对准小
便器中心。用垫紧块将其固定平整、端正，接好进水管道。
出水配管的连接根据小便器的不同选择安装如尺寸图所示。
（参见”尺寸图”）
注意：
a. 不要将进出水方向弄错。
b. 将本产品连接上供水管前，建议先冲洗干净供水管。
6
1206437-T01-A

Please directly reference to Step 3 when installinig DC.
Please match 16306T-NA AC power unit when installing
AC. The way of installation is as below.
CAUTION:
a. Outlet of AC power unit upward prohibited.
b. Do not connect 220V C power supply to DC wiring
terminal.
c. Do not damage the covering of AC power unit or
remove screws to avoid leakage.
A. Fig.#1: AC power unit connection way 1:
AC power unit is directly connected to electric control box.
Fig.#2: AC power unit connection way 2:
AC power unit is connected to electric control box by
connection wire.
安装直流型请直接参考第3步。
安装交流型请选配16306T-NA交流电源盒，安装方式如下：
警告：
a. 禁止将交流电源盒出线朝上安装。
b. 禁止将220V交流电源接入直流接线端。
c. 安装时严禁损伤交流电源盒外壳或移开电源盒盖螺
钉，以防止受潮漏电。
Outlet downwards
出线朝下安装 Outlet upwards
出线朝上安装
Connect to
sensor
接感应器
Connect AC
Power Supply
接交流电源
Connect to
sensor
接感应器
Connect AC
Power Supply
接交流电源
A. 图1：交流电源盒连接方式一：
交流电源盒与电控盒直接相连。
图2：交流电源盒连接方式二：
交流电源盒通过连接线与电控盒相连。 AC
交流电源
Connector
接插件 Wire prepared
by customer
连接线用户自备
Connector
接插件
16306T-NA
AC Power Unit
交流电源盒 Connect with the same color wire,
and protect connect area by insulation tape.
请按电线颜色对接
连接处用绝缘胶布包好
16306T-NA
AC Power Unit
交流电源盒
AC
交流电源
Connector
接插件
Fig.#1
图1
Fig.#2
图2
B. When installing the AC power unit in cassette, please
layout the bushing according to Fig.#3, and thread the
wire through the bushing.
Fig #3:connection sketch AC power unit install in cassette.
CAUTION: One AC power unit can supply two sensors at
most.
B. 将电源盒放在阀盒中时，如图示安装电工套管，管内装
入电线。
图3：交流电源盒安装在阀盒内的连接示意图。
警告：一个交流电源盒最多可连接两个感应器。
Bushing
电工套管
Fig.#3
图3
Connect 220V AC
接220V交流电
1206437-T01-A
7

C. When installing the power unit on the ceiling, please
layout bushing according to Fig.#4 and thread wire through
the bushing.
Fig.#4: Connection sketch while installing power uint on the
ceiling.
CAUTION: One AC power unit can supply two sensors
at most.
NOTICE:
a. Keep the connector away from water.
b. Don’t mistake the direction of inlet and outlet.
c. Do not connect the DC output of AC power unit to AC
power supply.
d. Do not connect to power supply while installing. Connection
line is not supplied. AC connection wire with insulating
sleeving is recommended. Wire of which the nominal section
area of conductor is not less than 0.5mm2is also recommend.
DC connection line use wire of which the nominal section area
is not less than 0.3mm2. It is cut according to acted installation
requirements (The length of cut wire is recommended less than
10m).
e. The head AC power supply must be protected with
appropriate fuse.
f. Please confirm the AC power supply and water supply should
be shut off before maintaining the products with AC power
related.
C. 将电源盒放在天花板上，如图示安装电工套管，管
内装入电线。
图4:交流电源盒安装在天花板上的连接示意图。
警告：一个交流电源盒最多可连接两个感应器。
Bushing
电工套管
Ceiling
天花板
AC Power Unit
交流电源盒
Fig.#4
图4
注意:
a. 不要让电线接插件接触水。
b. 不要将进出水方向弄错。
c. 不可将交流电源盒的直流输出端与交流电连接。
d. 安装时不要向电源盒供电。连接线请用户自备，建
议交流电源线采用导体标称截面积≥0.5mm2的电线，
直流连接线采用导体标称截面积≥0.3mm2的电线，
电线长度根据实际安装需要自行裁剪（建议连接线
长度小于10m）。
e. 交流电的总电源必须有合适的熔断丝加以保护。
f. 维修时必须断开交流电源并关闭水源。
3. When the slurry turns solid, remove the short screws, pull
out slurry mold, mount the bracket assy., and secure with
long screws.
Short Screw M4 x 10
M4 x 10
Slurry Mold
Long Screw M4 x 50
M4 x 50
3. 灰浆固化后，取下短螺钉，揭去灰浆模套，并用长螺钉
固定安装架。
8
1206437-T01-A

Note:
Don't mistake the polar of the batteries
and don't mix new and used batteries
together. When out of power, the indicator
will flash every 2 seconds and the sensor
will not work until new batteries are supplied.
When replacing the batteries, open the cover
of battery box and put in the new batteries.
Put on clean gloves when install sensor
cover to avoid surface damage by cement
or sand.
b
a
Battery box Assy
Indicator
Fig.#5
5
注意:
电池极性不能装反，新旧电池不能混用。电池
耗尽时，感应指示灯每隔2秒闪烁一次，感应
器停止工作，直至更换电池。更换电池时只需
打开电池盒盖装入新电池即可。
安装面板时应戴上干净的手套，以防水泥或沙
粒损伤表面。
4. Tighten the slurry mold and valve box with short screws and
then apply slurry into the service around the valve box. Lay
the tiles.
40
Valve Box
Tiles
Slurry Mold
4. 用短螺钉将灰浆模套与阀盒旋紧后,用灰浆填埋冲洗阀盒体
四周槽道，张贴瓷砖。
5. While using DC power, take out the battery box from the back
side of cover. Loose the screws of the battery box assy. with a
screw driver. Put 2 "AA" size alkaline batteries and
tighten the battery box's cover with the screws. Replace
the battery box . After connecting solenoid valve with
control box assy., install the cover as shown in theFig.#5:
a. Buckle the sensor cover into the wall slightly above
bracket assy.
b. Press the sensor cover down along the wall and fit
tightly into the bracket assy.
c. Push upward with hex wrench and rotate anticlockwise
to lock the sensor cover.
Screws
Batteries cover of Batteries Box
Battery Box
5. 用于使用直流电源时，十字螺丝刀旋开电池盒盖螺丝，装入
2节5号碱性电池，拧紧电池盒盖的螺丝后，将电池盒组件放
到图5所示位置。连接电磁阀和控制盒组件的接插件,如图5
安装面板：
a. 将面板在固定板稍偏上方的位置扣向墙面；
b. 紧贴墙面向下扣紧面板，使面板和安装架卡牢；
c. 用六角扳手上顶后，逆时针旋转，锁定面板。（顺时针旋转
即可取下面板）
1206437-T01-A
9

USER S GUIDE
Working Status Flushing
Deodorizing Flushing
Flushing Volume
When the water pressure or flush amount exceeds a certain
limit, take off the cover and turn the adjusting bolt clockwise
with hex pan to a proper place.
Manual Flushing
Normal working status, approach the supplied special magnetic
stick (flushing control stick) to the right part of the sensor lens.
The system is now at a manual status and the indicator will flash
every 1 seconds. Approach the flushing control stick to the right
part of the sensor lens once, it ll flush once. The maximum flush
time is approximately 30 seconds. This status will last for
about 8 minutes until turns to the normal working status.
If the flushing control stick keeps near to the
sensing window for 30 seconds, the manual
status will be terminated automatically and
reassume the normal working status.
NOTE:
Adjustment Bolt
调节栓
Flushing Control Stick
,
,
在正常工作模式下，用配备的专用磁棒（冲洗控制棒）靠近
感应窗口右侧位置，此时系统进入手控状态，感应指示灯每
1秒闪烁一次。用冲洗控制棒每靠近感应窗口右侧一次，小
便器即放水冲洗一次，冲水最长时间约为30秒。此状态维持
约8分钟。结束后转为正常工作状态。
当水压过大或冲水量偏大时,取下面板,使用六角扳手顺时
针方向调节水量调节栓至适量即可改善冲水量。
接通电源10秒后即可进入工作状态。
当连续有人使用时，小便器每2分钟自动冲洗一次。
If the urinal is used continuously, the urinal will flush every
2 minutes automatically.
The urinal enters into working status after the power is
connected for 10 seconds.
使用说明
工作状态
防臭冲洗
水流量
手控冲洗
注意：冲洗控制棒如持续超过30秒一直不离开感应窗口，
将自动解除手控冲洗状态回复到正常工作状态。
冲洗控制棒
PSD ECO 0.5&1L flush mode change
The default flush mode of sensor is 0.5L , you can switch to
the 1L flush mode with flushing control stick. Operate as
follow: after initial power on, during the time of the indicator
flashing, you can switch the flush mode by putting the flushing
control stick near the right part of the sensor lens. There will
be twice quick rinse after you complete the 1L flush mode
setting. If you need to reset the 0.5L flush mode, you can cut
off the power completely and restart the sensor, during the
time of the indicator flashing, you're able to switch flush mode
with flushing control stick, there will be once quick rinse after
you complete the 0.5L flush mode setting.
NOTE: just for 8881T-VC01-BN/AF(PSD ECO 0.5&1L /DC)、
8881T-VC03-BN/AF(PSD ECO 0.5&1L /AC)
0.5L和1L可调式冲洗模式切换:
产品出厂默认设置为0.5L冲洗模式，可以使用冲洗控制棒将产品
设置为1L冲洗模式。具体操作方法如下：产品初始上电，在指示
灯显示长亮的时间内，用配备的专用磁棒（冲洗控制棒）靠近感
应窗口右侧位置切换冲洗模式。设置1L冲洗模式成功后，会有连
续2次快速冲洗。若需切换回0.5L冲洗模式，可侧底断电后重新上
电，在指示灯显示长亮的时间内使用磁棒设置，设置0.5L冲洗模
式成功后，会有一次快速冲洗。
注：仅适用于8881T-VC01-BN/AF(0.5L&1L可调式/直流型)、
8881T-VC03-BN/AF(0.5L&1L可调式/交流型)
10
1206437-T01-A