Kohler FAIRFAX 12177T-B User manual

1230979-2A-B 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, assemble the faucet and drain to sink before installing.
3. The highest working pressure for handspray & shower head is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handspray,
shower head and the shower arm away from heater, or it may become damaged and cause injury to the user.
HANDLE OPERATION
Lift the handle gently. Turn clockwise for hot water, turn counter-clockwise for cold water.
1230979-2A-B 4
INSTALLATION INSTRUCTIONS
12177T-B Single Hole Kitchen Faucet12177T-B Single Hole Kitchen Faucet
FAIRFAXFAIRFAX
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering
Min.37
G1/2˝
185
Max.30
152
208
440
230
1500
19º
871128
871635
78148**
834554
834793
78064**
836530
865201
3017864**
865112
836009
865271**
77806
1000191**
836669
836583**
832940
871634
77420
1000194
1024405
3002357**
3005433
832687

1230979-2A-B 2 1230979-2A-B 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How To Install The Faucet
Slide the washer(2) into the groove of the body. Put the hoses into the
mounting hole of the sink. Let the bottom of the body against the deck.
From underside of the sink, place the bracket(3) and nut(4) onto the
mounting stud(1). Position the faucet so that mounting stud is toward the
back and the two hoses is symmetrical. Tighten the nut to secure faucet
to sink.
Attach the hoses to water supplies. When facing the front of the faucet,
the left hose is hot water, the right is cold water.
Put the fiber washer(6) into the connector(7) and thread it to the shank
(5). Lock the hose connector(8). Do not over tighten it.
Put the weight(9) onto the hose. Adjust the weight. The distance from the
faucet base to the weight will be 600~650mm. Tighten the screws to fix
up the weight.
Ensure that all coupling nuts are tight. Ensure that the lever handle is in
the off position. Turn on the main water supply and drain, and check for
leaks. Repair as needed.
Remove the hand spray(11), filter washer(10) and aerator(12). Run hot
and cold water about one minute to remove any debris. Remove any
debris from the filter washer and the aerator. Shut off the faucet. Reinstall
the filter washer, aerator and hand spray.
How To Use Spray
If you want to use the hand spray by hand, take the hand spray and pull
out the hose.
Press the button A as shown for the water flow.
NOTE: Please pull it gently and do not draw out the spray hose too long,
or you may damage the hose, connector and lossen the lead weight.
A
10
11
12
1
2
3
4
5
6
7
8
9
600~650mm
"LEAD FREE" is marked on the back of the faucet signifying its compliance with the United States AB1953