Kohler AIRFOIL 37273T User manual

BEFORE YOU BEGIN
1170832-2-C 1
37273T 花洒托架带软管
安装之前
安装尺寸 ROUGH-IN DIMENSIONS
INSTALLATION INSTRUCTIONS
安装说明书
Shower Bracket With Hose
安装步骤 INSTALLATION
为使安装顺利，G1/2″内螺纹管道配件
(1)应已装好。
注意：墙孔内需作防水处理。
To perform installation, installer must
provide G1/2" female supply fitting(1).
NOTE: The hole on the wall should
make waterproof treatment.
1
Finished Wall
装修好的墙面
奥睿
AIRFOIL
Ø40~45
G1/2"
12
28
60
214
90
G1/2"
G1/2"
G1/2"
1500±20
所有的资料是按最新出版的产品资料编写而成。科
勒公司保留任何时候不经通知即可改变产品特性、
包装或产品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
注意事项：
1. 一定要先彻底冲洗供水管以清除管道中的杂质。
2. 请特别注意此产品须远离加热器，否则可能损坏
产品，甚至对使用者造成伤害。
All information is based on the latest product
information available at the time of publication. Kohler
Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time
without notice.
Please leave these instructions for the consumer.
They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove
debris.
2. Please keep this product away from heater, or it
may become damaged and cause injury to the user.

1170832-2-C 2
清洗说明 CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗
镀层表面，再以干净的软布彻底擦干整个表面，许
多清洁剂，比如氨水、去污粉及洁厕灵等，会对电
镀表面造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌
的水龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
1156389
Connector
接头
零件图 SERVICE PARTS
**订购时请说明颜色编号
**Color code must be specified when ordering
1156391
Fixed Board
底座
835157
Screw
螺钉
1248781**
Hose
软管
在接头(2)的G1/2″螺纹上缠绕足以密封
的密封胶带或涂合适的密封胶。用
8mm六角扳手将接头旋紧到G1/2″内螺
纹管道配件上，且使其低于墙面
2~12mm。用螺钉(3)将底座(4)装到接
头上，使底座紧贴墙面，且两凸起(5)
水平。将接头组件(6)装入底座。将托
架组件(7)套在接头组件上，紧贴墙壁
且保持两个螺孔铅垂向下。用六角扳
手(8)锁紧螺钉(9)，固定托架组件。
去掉软管(10)两端接头的保护套。用软
管连接接头(11)。
Apply tape or thread sealant to G1/2"
threads of the connector(2). Tighten the
connector onto the G1/2" female supply
fitting, and below the finished wall
2~12mm. Install the fixed board(4) onto
the connector with the screws(3) so that
the fixed board is against the finished
wall, and keep two bulges(5)
horizontally. Install the connector(6) into
the fixed board. Slide the bracket kit(7)
onto the connector kit against the
finished wall, and keep two screw holes
downwards. Tighten the screws(9) with
the hex wrench(8) to secure the bracket
kit.
Remove the guards on the outlet
connectors of the hose(10). Connect
the connector(11) with the hose.
1
2
3
4
5
10
11
1156388
Connector
接头
870817
O-ring
O型圈
871527
O-ring
O型圈
1177979
Screw
螺钉
1046290
Hex Wrench
六角扳手
6
7
8
9