Kokido Racer Wizz RC30 User manual

AUTONOMOUS POOL ROBOT
USER MANUAL
ROBOT DE PISCINE AUTONOME
MANUEL D’UTILISATION
ROBOT DE PISCINA AUTOMÁTICO
MANUAL DE USUARIO
RC30

1
Table Of Contents
SAFETY WARNINGS & INSTRUCTIONS P.4
HOW THE ROBOT WORKS P.7
GETTING STARTED P.8
Charging The Battery P.8
Set-Up Before Use P.9
Floor Squeegee assembly P.9
Adjustment of Trajectory P.9
Locking pin P.9
Bumper P.10
Pool Preparation P.10
OPERATION P.10
EMPTYING THE DEBRIS COMPARTMENT P.12
MAINTENANCE & STORAGE P.13
BATTERY DISPOSAL P.13
How to remove the battery pack P.14
TROUBLESHOOTING P.15
Remark: Product/parts photos/drawings in this manual are for demonstration only.
Product/parts in photos/drawings may vary with the model purchased.

2
Table des matières
AVERTISSEMENTS ET INSTRUCTIONS P.17
FONCTIONNEMENT DU ROBOT P.20
POUR COMMENCER P.21
Chargement de la batterie P.21
Assemblage avant utilisation P.22
Installation des nervures de capture P.22
Ajustement de la trajectoire P.22
Goupille de verrouillage P.22
Pare-chocs P.23
Préparation de la piscine P.23
FONCTIONNEMENT P.23
VIDER LE COMPARTIMENT A DEBRIS P.25
ENTRETIEN & STOCKAGE P.26
RECYCLAGE DE LA BATTERIE P.26
Comment retirer la batterie P.27
DEPANNAGE P.28
Remarque: Les photos / dessins de produits / pièces de ce manuel sont uniquement
à titre de démonstration. Le produit / les pièces dans les photos / dessins peuvent
varier en fonction du modèle acheté.

3
Índice de contenidos
AVISOS E INSTRUCCIONES DE
SEGURIDAD P.30
FUNCIONAMIENTO DEL LIMPIAFONDOS P.33
PRIMEROS PASOS P.34
Carga de la batería P.34
Montaje previo al uso P.35
Instalación de la escobilla del suelo P.35
Ajuste de la trayectoria P.35
Pasador de seguridad P.35
Parachoques P.36
Preparación de la piscina P.36
FUNCIONAMIENTO P.36
VACIADO DEL COMPARTIMENTO DEL
FILTRO P.38
MANTENIMIENTO Y ALMACENAMIENTO P.39
ELIMINACIÓN DE LA BATERÍA P.40
Cómo retirar el paquete de baterías P.40
RESOLUCIÓN DE PROBLEMAS P.41
Observación: Las fotografías/ilustraciones del producto o de sus piezas que
aparecen en este manual solo se incluyen a modo de muestra. El producto o las
piezas que aparecen en las fotografías/ilustraciones pueden variar respecto al
modelo adquirido.

4
SAFETY WARNINGS & INSTRUCTIONS
Read and follow all instructions in this manual and on the equipment. Failure to do so
could result in severe or fatal injuries.
SAVE THESE INSTRUCTIONS
WARNING!
-This is not a TOY. Children should be kept out of reach from this robot and its
accessories.
-Never allow children to operate this product.
-You should not operate this electric vacuum when people/pets are present in the
water.
-This robot is not intended for use by someone with reduced physical, sensory or
mental capabilities or a lack of experience and knowledge unless they have been
given instructions concerning the appliance and are under supervision of the
person responsible for their safety.
-Make sure the robot is fully immersed in the water before operation. The minimum
water level required to operate the robot must reach above the swivel head of the
robot. Operating the robot when it is not immersed in the water correctly could
damage the unit and void the warranty as a result.
-Maximum operating depth in water is 3 meters (10 ft).
-Maximum water temperature: 5˚C(41˚F) –35˚C(95˚F)
-For the purposes of recharging the battery, only use the detachable supply unit
(external adaptor) provided with this robot.
-Detachable supply unit (external adaptor)
-Connect the external adaptor to a power source through a residential current
device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt, consult a
qualified professional electrician.
-Do not use this robot if any damage is detected.
-Replace damaged parts as soon as possible. Only use parts certified by the
distributor or manufacturer.
-Turn off the power, disconnect the external adaptor from the power source, and
unplug the external adaptor from the charging cable before detaching the robot
from the charging cable.
-Disconnect the robot from the supply mains and make sure the robot is power
OFF prior to servicing the product like cleaning the filter and swivel
smoothing-ring.
-Battery installed is a rechargeable Li-ion battery pack. Never attempt to replace
the battery pack.
-The robot is only to be recharged with external adaptor and charging cable
delivered with this product.
-DO NOT handle the robot, external adaptor and charging cable while it is charging
with wet limbs and without shoes.
-You should not operate this robot when people/pets are present in the water.
- DO NOT use this robot without an intact filter in place, as your warranty will be
voided as a result.
-Suction entrapment hazard: This robot generates suction. Do not allow hair, body,
or any loose parts of your clothing to make contact with the suction hole of the

5
robot during its operation.
-Never insert body parts, clothing or other objects into the openings and moving
parts of the robot.
-DO NOT use this robot to pick up any toxic substance, flammable or combustible
liquids such as gasoline, or in the presence of explosive or flammable fumes.
-Under no circumstances should you attempt to disassemble the robot and replace
the impeller, motor, and battery by yourself.
-Never insert fingers and any object to touch the impeller.
-This electric vacuum shall not be used by children.
-The battery must be removed from the electric vacuum before it is scrapped.
-This electric vacuum contains battery that are only removed by skilled persons.
-The electric vacuum must be disconnected from the supply mains when the
battery is being removed.
-For the battery disposal detail, refer to the section "Battery Disposal” in this
manual
-The battery is to be disposed safely in accordance with local ordinances or
regulations.
-Robot’s battery is a maintenance-free, rechargeable lithium-ion battery pack,
which must be disposed properly. Recycling is required; please contact your local
authorities for more information.
- External adaptor and charging cable:
Never use the external adaptor and charging cable for anything other than
charging the battery of the robot that is supplied in the same pack.
The external adaptor and charging cable should not be used outdoors, nor
exposed to rain, humidity, any liquid or heat.
The transformer ( or external adaptor) is to be located outside zone 1
Keep the external adaptor and charging cable out of reach of children.
Never use the external adaptor and charging cable if any damage is
detected.
DO NOT handle the external adaptor and charging cable with wet hands.
Keep the external adaptor disconnected from power when it is not in use.
Never attempt to open the external adaptor.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or an equally-qualified person in order to prevent hazards of
any kind.
Make sure the robot is completely dry before charging.
CAUTION!
- This robot is designed for underwater use only; it is not an all-purpose vacuum
cleaner. DO NOT attempt to use it to clean anything other than your pool.
- Use only original accessories delivered with this product.
- DO NOT use this robot right after pool-shocking. It is recommended to leave the
pool circulating for at least 24-48 hours.
- If you are using saltwater pool, make sure all salt are dissolved before placing the
robot into the water.
- It is not recommended to use this robot with another automatic cleaner/cleaner
simultaneously.

6
- Avoid picking up hard, sharp objects with this product. They may damage the
robot and filter.
- To avoid damaging the external adaptor and charging cable, do not carry the robot
by the cord of external adaptor / charging cable or pull the cord to disconnect it
from the power source and charging cable.
- Charge the robot indoor in a clean, dry area with good ventilation away from
sunlight.
- DO NOT leave the robot charged for over 10 hours.
- If the robot will not be used for an extended period, detach it from the charging
cable and use a damp cloth to clean and dry the robot and accessories. Make sure
to charge the robot to about 30% to 50% of the battery capacity before it is stored.
Store in a well-ventilated area away from sunlight, heat, ignition sources, pool
chemicals, and children. Recharge the robot every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.

7
HOW THE ROBOT WORKS
1 Swivel head
2 Sliding switch
3 Power indicating
light
4 Water sensors
5 Charging port
6 Side flap
7 Swivel
smoothing-ring
8 Top cover
9 Filter cover
10 Draining filter
plate
11 Suction mouth
flapper
12 Bumper x 2
13 Locking pin x 2 (1
pin is fixed)
14 Grip (under
Orange triangle
pattern)
15 Floor Squeegee
16 Float cover
17 Float
18 Hook (for
Telescopic pole)
19 Charging cable
The robot has a water propelling nozzle at the bottom of the top swivel head. Water is first
sucked in from the suction mouth on at the bottom of the robot, goes through the filter
and then discharged from the propelling nozzle. Water jetting from the nozzle propels the
robot forward. Once the robot stops against an obstacle like pool wall, its side flap rotates
and its swivel head turns 180o. The robot will start moving in the opposite direction. The
robot moves in a generally straight pattern in one direction and in an arc pattern in the
other direction. While moving, the robot vacuums pool bottom capturing the debris inside
the debris compartment.

8
GETTING STARTED
Charging The Battery
IMPORTANT NOTE: Fully charge the robot (about 5-6 hrs) before using it for the first
time.
WARNING!
Use only the original external adaptor and charging cable provided.
Make sure the robot and the charger port are clean and dry before set-up.
Make sure that the robot is turned off by sliding the switch to OFF position prior to
charging.
1. Place the unit on a flat surface. Sliding the switch to the OFF position.
2. Connect the adaptor cable to the charging cable. Align and insert the plug of charging
cable into the charging port on the top of the unit.
3. Connect the external adaptor to the power source. Once the robot begins charging,
the indicator light on the external adaptor will turn red. Normally, it takes about 4.5-5
hours to reach a full charge. The indicator light will turn green when the robot is
almost fully charged.
Immediately disconnect the external adaptor from the power source if you detect any
of the following conditions:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
4. When charging is complete, disconnect the external adaptor from the power source
and unplug the charging cable from the unit and external adaptor.
Normally the robot can be operated up to 90 minutes on a full charge.
Note: Clean the debris compartment regularly. Excessive debris inside the debris
compartment will increase the burden to the motor operation and shorten the operating
duration as a result.
NOTE: Rechargeable lithium-ion battery is classified as a consumable item. It has a
limited life and will gradually lose its capacity to hold a charge. Therefore, the running
time of the robot will gradually reduce after repeated charging and discharging
throughout its product life.

9
NOTE: Let the robot rest for around 30 to 40 minutes before charging it again.
Set-Up Before Use
FloorSqueegee Assembly
Align and insert all squeegees into the notches on the underside of the robot
Adjustment of Trajectory
Locking Pin
The position of the pin locking the axle will affect the trajectory. There are two locking
pins: locking pin on left is fixed and should remain untouched. Chang the right pin
location.
Factory setting of the pin
for all types of pool.
If the robot trajectory is too
curved, pull outthe pin and
insert it in this hole. Make
sure the wheel axle is
positioned below the axle.
To increase the curve of
the trajectory, remove the
pin from the hole and insert
it in the hole which is
located above the pin hole
as shown

10
Bumper
The bumper is optional and will be used in the following situations:
If the robot tends to follow the perimeter of
the round pool, clipping a bumper on each
side of the robot will eliminate this pattern.
If the robot tends to stay longer in some
areas of square or narrow rectangular
pool, placing a bumper at the front and
end of the robot will eliminate this pattern.
Pool Preparation
- If there are stones, roots or metal corrosion in contact with the underside of the liner,
discard them prior to using the robot. If necessary, seek assistance from a qualified
professional.
- If the liner is brittle, damaged or wrinkled, contact a qualified professional to perform
the necessary repairs or perform a liner replacement prior to using the robot.
- It maybe advisable to turn off the filtration system as water circulation in pool may
affect the robot movement pattern.
- Move pool ladder, surface skimmer and other floating objects from the pool as it may
obstruct the movement of the robot’s float and, consequently, also the movement of
the robot.
- If you are using saltwater pool, make sure all salt are dissolved before placing the
robot into the water.
OPERATION
WARNING! Make sure to switch off the robot at first.
1. Bring your robot to the side of your pool. NOTE: Do not place the robot in the pool
corner and against the pool wall as starting location. Attach the hook of the float to the
handle of swivel head. Pry to detach the float cover and release the rope from the
float to the length equivalent to the depth of pool water plus about 0.5 meters (1.6
feet). Put the rope inside the notch and roll the rope around the post until the cover
almost reaches the post. Put the rope inside the notch and close the cover as shown.

11
2. Hold the handle of swivel head and move the robot to the water surface and slide the
switch to ON position. Power indicator light will turn on.
3. Immerse the robot into the water. Robot will start the operation automatically as soon
as the water covers the water sensors on top of swivel head. Let the robot sink to the pool
floor. Orient the robot with its front/back facing the pool wall with help of the rope.
Observe the cleaner's first forward and reversed movements over the pool bottom. If the
robot runs along the pool wall instead of running perpendicular to it, reposition it making
sure that its front/back faces the pool wall.
Power indicator light starts to blink when remaining power is down to 10 minutes.
Power indicator light :
No light -
Power off / no power
Light - Power on
Blinking light -
Battery power will be exhausted within 10 minutes.
NOTE:
- Never attempt to make contact with both water sensors with anything other than water.
4. To retrieve the robot from the pool, catch the float and pull the rope to retrieve the
robot. If float is so far to be caught by hand, use the hook provided. Place the hook on
the telescopic pole (not provided) and then use the hook to catch the float. Once robot
is coming to water surface, catch and hold the grip located at the end of cleaner’s
bottom (underneath “blue triangle pattern”) and lift the cleaner to drain out the
water from the robot.

12
5. Slide the switch to OFF position. Rinse the robot with fresh water after every use. DO
NOT use any detergent.
NOTE: To ensure the most efficient cleaning, in the case your pool is quite dirty, it is
recommended to empty the debris compartment (inside the robot) after the first 30min of
operation, or whenever the robot’s movement has slowed down noticeably. Then place
the robot (with the debris compartment already emptied) back into the pool, and let it run
through the remaining of its cycle.
EMPTYING THE DEBRIS COMPARTMENT
WARNING! Using the robot without its filter cover in place will VOID your
warranty.
In order to maximize the cleaning efficiency, clean the debris compartment and the filter
cover before and after each use.
CAUTION! Before cleaning the debris compartment, make sure to turn off the robot by
sliding the switch to OFF position.
1. Place the cleaner on a stable and flat surface. Pull one side clip outward and lift up
the cover to release the top cover at first and then release another clip by same way.
Remove the top cover and detach both filter cover and draining filter plate.
2. Clean out the debris out of the compartment. It is recommended to clean the filter
cover net and draining filter plate with splashing water. If brushing is deemed necessary,
use only a soft brush to clean it carefully and gently. DO NOT apply any pressure to the
net.
3. After cleaning, make sure that both draining filter plate and the filter cover are in place
and the body top cover is secured by the side clips. Side clips should clip completely
into the cleaner by pressing them inward.

13
CAUTION! Replace a damaged filter cover immediately with a new one before the next
operation.
MAINTENANCE & STORAGE
NOTE:
1. Battery discharges on its own during storage. Make sure to fully-charge the robot
before storage.
2. You must re-charge the battery at least once every three months when it is not in use.
Unplug the external adaptor from the socket and then unplug the charging cable from
the external adaptor and robot.
Detach accessories from the robot. If necessary, rinse the robot and accessories with
fresh water. DO NOT use detergent.
Be sure to drain the water from the robot before storing it.
Use a damp cloth to clean and dry the robot and its accessories.
Store them in a well-ventilated area away from sunlight, heat, ignition sources, pool
chemicals and from children. Ambient temperature for storage should be 10˚C – 25˚C
(50˚F – 77˚F). NOTE: A higher storage temperature may reduce the battery life.
WARNING!
-Under no circumstances should you attempt to disassemble the robot swivel head
and replace the impeller, motor and battery by yourself.
-To replace a damaged squeegee, push it out of the cavity and replace it with a
new one.
CAUTION!
Excessive heat can damage the battery and reduce the lifespan of your robot as a
result.
Consult your dealer regarding battery replacement if the following happens:
-Battery appears damaged or will not charge fully.
-Battery operation time is noticeably reduced. Observe and record the run times
of the first few operations (on a full charge). Use these run times as a reference
point to compare with run times of older batteries.
The battery must be removed from the robot before it is scrapped.
The robot must be disconnected from the supply mains when the battery is being
removed.
The battery is to be disposed safely in accordance with local ordinances or regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a
result.
BATTERY DISPOSAL
Your robot is equipped with a maintenance-free rechargeable lithium-ion battery pack,
which must be disposed of properly. Recycling is required; please contact your local
authority for more information.
WARNING! Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces and watches when the
battery pack is unwired from the robot.
A battery can produce a short circuit current high enough to weld a ring (or similar item)
to metal, causing a severe burn in the process.

14
Wear complete eye protection, gloves and protective clothing when the battery pack is
being removed.
Avoid touching the wires altogether and avoid allowing them to make contact with any
metal items, which could cause sparking and/or short circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the robot.
Do not expose the battery to fire or intense heat as this may result in an explosion.
CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with plenty
of soap and water.
-If leaking fluids come in contact with eyes, do not rub eyes, immediately flush eyes
with cool running water for at least 15 minutes and do not rub them. Seek medical
attention as soon as possible.
How to remove the battery pack
Recommended tools (not included): Screwdriver.
1. Follow section “EMPTYING THE DEBRIS COMPARTMENT” to release the top
cover (preassembled with the swivel head). Up side down the cover and release the
swivel head by turning its bottom locking plate anticlockwise. Remove the swivel
smoothing-ring.
2. Use the screwdriver to unscrew the 4 screws located on the bottom of the head to
release the bottom plate at first. Use the screwdriver to unscrew all the screws on the
base as shown. Remove the impeller and then pry up the base and remove it to
expose head inside.
3. Move out the battery pack to expose the PCBA. To detach the battery connection
wire, press the clip on the connector and then pull it out. NOTE: Wrap the connector
immediately with insulating tape in order to avoid short circuit caused by contact of
both wire terminals.

15
TROUBLESHOOTING
Problem Possible Cause Solution
Battery is running out Charge the robot again.
Impeller is jammed Power off the robot and visually check the hole under the
swivel head to see if the impeller is jammed by larger
debris. If necessary, contact your dealer for further
instructions.
WARNING! Make sure the robot is powered off
when the unit is being serviced.
Impeller is broken Contact your dealer for replacement.
Robot does not capture the debris
Debris compartment is full Clean both debris compartment and filter cover.
Robot stopped by obstacle Check to see that if there is nothing obstructing the
cleaner. Remove the obstacle.
Robot stopped moving in the middle of
pool but swivel head is still turning
Robot is stopped by suction
force from pool floor main drain
Turn off the filtration system as instructed in manual.
Debris compartment is full Clean the debris cleaner
Operation time is shorter as
expected
Clean the filter compartment and recharge the robot
again for 4.5- 5 hrs
Moving direction is interrupted
by water circulation generated
by filtration system
Turn off the filtration system as instructed in manual.
Wheel is jammed Check and clean out debris from the wheel.
Locking pin position is not
correct / bumper is required
Follow instruction to set up the locking pin position
properly and apply bumper .
Robot does not cover the entire pool /
move along the pool wall
Robot moves along the pool
wall of round pool
Make sure the bumpers have been installed as instructed
in manual.
Robot trapped in the narrow place of
the in-ground pool
No enough space for robot
turning in other direction
Follow instruction to put bumper on both end of robot.
Robot moves slowly Debris compartment is full Clean both debris compartment and filter cover.
Swivel head does not turn or turn
noticeably slowly
Swivel head bottom is jammed Check and remove any debris that may be trapped under
the swivel head.
Side flap is jammed Check and remove any debris that hinders the
movement of the flap.
Swivel smoothing- ring is
broken
Replace with a new swivel smoothing-ring. Contact your
dealer for replacement parts.
Debris escapes from the robot Suction mouth’s flap (on Suction mouth’s flap works like a door to prevent the

16
cleaner bottom) is broken debris from escaping from the debris compartment.
Contact dealer for replacement parts and instruction.
Draining filter plate is broken or
not in place
Make sure the draining filter plate is in place and replace
a new one if necessary before next use.
Debris goes outside the filter cover Filter cover net is damaged Replace with a new filter cover. Contact your dealer for
replacement parts.
seogretawdnanekorbsitaolFsknistaolF
in
Replace with a new float. Contact your dealer for
replacement parts.
Battery is damaged Contact dealer for battery replacement.
WARNING! DO NOT open the robot and
replace the battery by yourself. This could result in
severe or fatal injuries and the warranty will be voided as
a result.
Charging cable is not
completely connected with
external adaptor and robot.
Make sure that the charger cable is connected with
external adaptor and robot properly and completely.
Refer to instruction manual.
Robot cannot be charged / recharged
External adaptor is out of order Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the robot / battery and voiding the
warranty as a result.
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that
properly recycles electrical and electronic equipment. Do not dispose them in unsorted waste
bins. For items containing removable batteries, remove batteries before disposing of the
product.
© 2018 Kokido Development Ltd. 18001025
All rights reserved. No part of this document may be reproduced or transmitted in anyform or
by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior
written permission of Kokido Development Ltd. (V1)
If soft copy of this instruction manual is required, please contact our customer service by email:
[e-mail]
SAVE THESE INSTRUCTIONS
Manufacturer: Kokido Development Limited.Unit 1319, Sunbeam Centre, 27 Shing Yip Street, Kwun Tong, Kowloon, HK

17
AVERTISSEMENT & INSTRUCTIONS
Lire et respecter toutes les instructions de ce manuel. Ne pas le faire pourrait
entraîner des blessures graves ou mortelles.
CONSERVER CE MANUEL
AVERTISSEMENT!
-Ce produit n'est pas un jouet. Les enfants doivent être gardés hors de portée de
ce robot et de ses accessoires.
-Ne jamais laisser les enfants utiliser ce produit.
-Ne pas utiliser ce produit lorsque des personnes/animaux sont dans l’eau.
-This robot is not intended for use by someone with reduced physical, sensory or
mental capabilities or a lack of experience and knowledge unless they have been
given instructions concerning the appliance and are under supervision of the
person responsible for their safety.
-Ce robot n'est pas destiné à être utilisé par une personne ayant des capacités
physiques, sensorielles ou mentales réduites, ou ayant un manque d'expérience
et de connaissances, à moins d'avoir reçu des instructions concernant l'appareil et
d’être sous la surveillance d’une personne responsable de leur sécurité.
-Assurez-vous que l’aspirateur électrique est complètement immergé dans l'eau
avant de commencer l'opération. Le niveau d'eau minimum requis pour faire
fonctionner l'appareil doit être au-dessus de la tête rotative du robot. Le produit est
uniquement destiné à être utilisé sous l'eau dans une piscine; Toute autre
utilisation annulera la garantie.
-Profondeur maximale d’utilisation : 3 mètres (10 ft).
-Température de l’eau maximum: 5˚C(41˚F) –35˚C(95˚F)
-Pour recharger la batterie, utiliser uniquement l'unité d'alimentation détachable
(adaptateur externe) fournie avec ce robot.
-Unité d'alimentation détachable (adaptateur externe).
-Connecter l'adaptateur externe à une source d'alimentation par l'intermédiaire
d'un dispositif de courant résidentiel (RCD) ou d'un disjoncteur de fuite à la terre
(GFCI). En cas de doute, consultez un électricien professionnel qualifié.
Ne pas utiliser cet aspirateur électrique si des dommages sont détectés.
-Remplacer les pièces endommagées dès que possible. N'utiliser que des pièces
certifiées par le distributeur ou le fabricant.
-Mettre l'appareil hors tension, débrancher l'adaptateur externe de la source
d'alimentation, et débrancher l'adaptateur externe du câble d’alimentation avant
de débrancher le robot du câble d’alimentation.
-Débrancher l’aspirateur électrique du réseau d'alimentation et s’assurer que le
robot est éteint avant d'effectuer tout entretien, tel que le nettoyage du filtre.
-La batterie installée est une batterie rechargeable Li-ion. Ne jamais essayer de la
remplacer.
-Recharger ce robot uniquement à l’aide de l’adaptateur externe et du câble de
d’alimentation livré avec ce produit.
-Durant la charge, NE PAS manipuler le robot, l’adaptateur externe ou le câble
d’alimentation en condition d’humidité ou sans chaussures.
-NE PAS utiliser ce robot sans un filtre en bon état, la garantie serait annulée.

18
-Risque d'entrave par aspiration: ce robot génère de l'aspiration. Ne pas laisser les
cheveux, le corps ou les parties flottantes de vos vêtements dans la plage
d'aspiration du produit pendant son fonctionnement.
-Ne jamais introduire une partie du corps, vêtements ou autres objets dans les
ouvertures ou les parties mobiles du robot.
-NE PAS utiliser ce robot pour ramasser des substances toxiques, inflammables
ou combustibles comme l'essence, ni en présence de vapeurs explosives ou
inflammables.
-Ne jamais tenter de démanteler les pièces de ce robot, remplacer la turbine, le
moteur ou la batterie par vous-même.
-Ne jamais insérer les doigts ou quelconque objet dans la turbine.
-Ne doit pas être utilisé par des enfants.
-La batterie doit être retirée de l'aspirateur électrique avant d'être mis au rebut.
-Cet aspirateur électrique contient une batterie qui ne peut être retirée que par des
personnes qualifiées.
-L'aspirateur électrique doit être déconnecté du réseau d'alimentation lorsque la
batterie est retirée.
-Pour plus de détails sur la mise au rebut de la batterie, se reporter à la section
"Mise au rebut de la batterie" de ce manuel.
-La batterie doit être détruite en toute sécurité conformément aux réglementations
locales.
-La batterie du robot est une batterie rechargeable au lithium-ion qui ne nécessite
pas d’entretien, et qui doit être détruite correctement. Le recyclage est obligatoire,
veuillez contacter les autorités locales pour plus d'informations.
- Adaptateur externe et câble d’alimentation:
Utiliser l'adaptateur externe et le câble d’alimentation uniquement pour
recharger la batterie du robot fourni dans le même pack.
L'adaptateur externe et le câble d’alimentation ne doivent pas être utilisés à
l'extérieur, ni exposés à la pluie, à l'humidité, à des liquides ou à la chaleur.
Le transformateur (ou l'adaptateur externe) doit être situé à l'extérieur de la
zone 1
Garder l’adaptateur externe et le câble d’alimentation hors de portée des
enfants.
Ne jamais utiliser l’adaptateur externe ou le câble d’alimentation s’ils sont
endommagés.
NE PAS manipuler l’adaptateur externe ou le câble d’alimentation avec les
mains humides.
Conserver l'adaptateur externe hors tension lorsqu'il n'est pas en usage.
Ne jamais essayer d'ouvrir l'adaptateur externe.
Si le cordon d'alimentation est endommagé, il doit être remplacé par le
fabricant, son agent de service ou une personne également qualifiée afin
d'éviter tout danger.
S’assurer que le robot est complètement sec avant de le recharger.
MISE EN GARDE!
- Ce robot est conçu pour une utilisation sous l'eau uniquement; ce n'est pas un
aspirateur tout usage. NE PAS essayer d'utiliser l’aspirateur électrique pour nettoyer
autre chose que votre piscine.

19
- N'utilisez que des accessoires d'origine fournis avec ce produit.
- NE PAS utiliser ce robot juste après la mise en service de la piscine. Il est
recommandé de laisser d'abord la piscine fonctionner pendant au moins 24 à 48
heures.
- Ne pas utiliser cet aspirateur électrique avec un autre aspirateur / nettoyeur
électrique simultanément.
- NE PAS utiliser cet aspirateur électrique juste après la mise en service de la piscine.
Il est recommandé de laisser d'abord la piscine fonctionner pendant au moins 24 à 48
heures.
- Pour les piscines d'eau salée, s’assurer que tout le sel est dissous avant de placer
le robot dans l'eau.
- Il n'est pas recommandé d'utiliser ce robot simultanément avec un autre aspirateur
électrique.
- Éviter de ramasser des objets durs et tranchants avec ce produit. Cela peut
endommager le robot et le filtre.
- Pour ne pas endommager l'adaptateur externe ou le câble d’alimentation, ne pas
porter le robot par le cordon de l'adaptateur externe ou par le câble d’alimentation,
ne pas tirer sur le câble pour le débrancher de la source d'alimentation.
- Charger le robot à l'intérieur, dans un endroit propre et sec, avec une bonne
ventilation et à l'abri du soleil.
- NE PAS laisser l’aspirateur électrique branché sur le chargeur pendant plus de 10
heures.
- Si le robot n'est pas utilisé pendant une période prolongée, s’assurer qu'il est éteint
et utiliser un chiffon humide pour le nettoyer et le sécher, faire de même pour les
accessoires. S’assurer de recharger l’aspirateur électrique à 30%- 50% avant de le
stocker. L’entreposer dans un endroit bien ventilé, à l'abri de la lumière du soleil, de la
chaleur, des sources d'ignitions, des produits chimiques de la piscine et des enfants.
Recharger l’aspirateur électrique tous les trois mois
Les avertissements et mises en garde ci-dessus ne sont pas destinés à lister
tous les cas possibles de risques et / ou de blessures graves. Les Propriétaires
de piscine doivent toujours faire preuve de prudence et de bon sens lors de
l'utilisation du produit.