komodo ATVSS350 User manual

Owner's Manual Owner's Manual
Congratulations on your purchase. You have purchased a dependable and sturdy seeder/spreader,
but only by proper care and operation can you expect to receive the service and long life designed
and built into it. This manual contains valuable information about your new Seeder/Spreader. It has
been carefully prepared to give you helpful suggestions for operating, adjusting, servicing and
ordering repair parts.
#ATVSS350
350lbsSeeder/Spreader
350lbsSeeder/Spreader

Keep this manual in a convenient place for quick and easy reference. Study it
carefully. If in the future your seeder may need new parts to replace those that are
worn or broken, if so, call 1 [phone] and provide the model, part number, and
proof of purchase and we will replace the part as outlined in our Limited Warranty.
WARNINGS WARNINGS
1
PartsList/Diagram PartsList/Diagram
Readandunderstandtheinformationcontainedinthismanual.
Operate, lubricate, assemble and maintain the equipment in accordance with all
instructionsandsafetyproceduresinthismanual.
Inspect the equipment and replace or repair any parts that are damaged or worn which
under continued operation would cause damage, wear to other parts, or cause a safety
hazard.
Paymentofallcostsincurredfortransportingtheequipmentorpartsforwarrantyinspection
andorclaims.
It is the purchaser and/or operator's responsibility to:
Contents Contents
Assembly
Introduction
General Information
Safety Information
Connections
Spreader Use
Maintenance / Storage
Warranty
2
5
5
5-7
8
8-10
10-11
11
The spreader comes partially assembled, the transmission and drive shafts are factory
assembled.
1
2
345
6
7

1
3
3
7
23145
2
6
3
1
ATTENTION!
PLEASE MAKE
SURE TO
TIGHTEN ALL
OFTHE BOLTS
AssemblyInstructions(Removable) AssemblyInstructions(Removable)
2
Removespreadercomponentsfrombox;checkthatyoureceivedallnecessaryparts.
Ifyouaremissingacomponentpleasecall(800)333-8889forreplacement.
1.
Attachthetowbaradjustableplank(2)
totheframeplate(1),using4ea.(M8)
Bolts(4),nuts(3),andlockwashers(5),
asshown.
2.
Assemblecoupler(2)totowbar(1),
using2ea.(M12)bolts(3),nuts(4)
andlockwasher(5).
3.
1
5
2
4
3
1
5
4
3
2
Assembletowbar(1)toadjustable
bracket(2),using1ea.(M12)main
bolt(5)andlocknut(6). Attachangle
adjustmentbolt(3)using1ea.(M8)
bolt(3)andlocknut(4).
Note:theadjustmentboltis
usedtolevelthespreaderfor
correctspread,placewhere
neededtokeepspreaderlevelto
vehicleandterrain.
4. 1
4
25
3
6
5. Assemblehopperandbottomplateassembly.
Makesurelabelonhopperandbottomplate
assemblylineup.Leaveboltslooseuntilall
areinplace,andthentighten.Fastenerheads
tobeinsidehoppersonottointerferewith
spreadermaterial.
Attachthesides(7,4,2)payingattentionto
whichsideisfront(7)using24ea.(M6)bolts(1)
andnuts(3).Nextinstallcornercapsusing
8ea. (M6)bolts(1)andnut(3).Thenfinally
attachbottomplateassembly(6)using12ea.(M6)bolts
(1)andnut(3).

LABEL SHOULD
BE UPWARDS. 2
3
1
44
5
2
3
1
4
5
6
65
2
5
6
Assemble wheels to Spreader using 2 ea.
(M8) bolts, flat washers, and lock nuts. Then
assemble hopper to spreader base using 3
ea.(M10)bolts(4),nuts(2)andlockwashers
(5). Fasten heads inside hopper as
shown.
6.
Assembly wind drift braces (3) using 3 ea.
(M8) bolts (2), nuts (4), flat washer (6), and
lockwashers(5),attachasshown.
7.
Attachwinddrift shield (2) with 3 ea. (M6) bolt
(3), nuts (4), flat washer (7) and lock washers
(6)asshown.
8.
236
5
4
7
1
4
2
1
3
6
5
4
Attachhopperauger (3) to shaft(1)using1 ea.
(M10)bolt(2),nut(4)andlockwasher(5).
Makesurelabelfacesupwardasshown.
9.
3

4
3
2
1
Assembleguideassemblyasshownusinglockknob(2),guide(3)andsquarenut(4).
9.
Attachleverstofeedadjustplatesasshown.
Attachlever(5)throughfeedscalemountusing1ea.(M10)bolt(2),flatwasher(16),spring
(3),handlewasher(4),andlocknut(6).
Place connecting rod (1) through hole at bottom of lever (5) and attach using flat washer
(15)andcotterpin(17).
Placeotherendofconnectingrod(1)intoarmoftopplateandattachusingflatwasher(15)
andcotterpin(17).
Next attach lever (7) to fixed pin (11) using flat washer (8) and cotter pin (9). Then attach
oppositeendoflever (7)tobottom platearmusingshaftpin(14), flatwasher (8)andcotter
pin(9).
11.
1216 34 5 6 7 89
10
11
12
15
17
8
14
13
15
4

Introduction Introduction
The Big Roc Spreader is a standard centrifugal spreader and is used for the distribution of
granular fertilizers, seeds, salts, etc. It can be used by most small / medium powered vehicle
(ATV,Tractor,Etc.)
Thoroughly read this manual before operation of spreader and follow all assembly and
maintenanceprocedures/recommendationsto help ensure safe and efficientoperation of the
spreader.
This manual is provided to give the customer operational information and safety rules on the
machine, as well as maintenance instructions. Please keep manual handy to refer back to for
reference.Iflostpleasecalltogetanewcopy.
GeneralInformation GeneralInformation
This manual gives important information in the care and proper use of the machine. The
dependability and longevity of the machine depends on the maintenance and attention to the
correctinformationincludedinthemanual.
Somepictures inthismanual mayshowdetailsoraccessoriesthatmaybe differentthanthose
of your machine, in order for clarity some items may be removed to allow better view or
description.Makesureyouclearlyunderstandpictures,ifnotcallforabetterexplanation.
Throughoutthismanualyouwillseesymbolslikethese:
Thesymbolontheleft,withwordsshown:
DANGER
ATTENTION
WARNING
Are used in this manual to draw your attention to the safety and
properoperationof themachine,it isnecessaryto observeallwritten
rules,asthesepointoutspecificareasthatmaycausedamagetothe
machineorpersonalinjurytooperator.
ImportantSafetyInformation ImportantSafetyInformation
THE FOLLOWING SAFETY RECOMMENDATIONS ARE TO SAFEGUARD YOU
THEREFORE IT IS NECESSARY TO READ THEM CAREFULLY, MEMORIZING AND
ALWAYS APPLYING THEM.
The warnings in this manual regard exclusively the allowed uses and reasonably
foreseeable. All below Instructions must be used with common sense and adequate
measurestopreventaccidents.
Themachinemustbeusedbyanexperienced,ofageoperator.
Allthelistedinstructionsmustbecarefullyrespected.
Possible changes to the machine, not authorized by the manufacturer (by written copy),
excludehisresponsibility.
Checkforcorrectfunctioningofthemachine,beforeeveryuse.
Carefully read this manual before proceeding to start, operate, employ or maintenance the
machine.
Watch, in addition to the warnings of this manual, all the safety, accident prevention rules of
generalnature.
The manual must always be handy, so as to consult it, in order to check working cycle and
safetyinformation.Incaseoflossordamage,itwillbenecessarytoaskforareplacementcopy.
5

ATTENTION ATTENTION
Any work of maintenance, adjustment and cleaning must be done with the machine on the
ground(stableconditions),turningofftheATVorlawntractorengineandremovingthekey.
Readcarefullythesafetylabelsappliedonthemachineandfollowtheinstructions.
ATTENTION-WARNING ATTENTION-WARNING
The operator during the period of use, maintenance, repair, handling or storing of the
machine must wear accident-prevention shoes and safety gloves. Moreover, if it is
necessary he must wear suitable protections such as earplugs, dust masks and protective
glasses.
During loading, there is the danger of powders inhalation produced by fertilizer mixing. It is
suggested to use suitable safety systems of breathing, like powder masks or masks with
filter.
The machine is designed for being used by a single operator who, during the use, must
alwaysstayinthestationingcontrolonthevehicle.
Neverworkwiththismachineifyouaretired,sickorafterdrinking,drugsormedicines.
DANGER DANGER
Itisforbiddentoclimbortotransportsomebodyonspreader.
Do not put hands inside the hopper for any reason while machine is in motion or capable of
movingunderitsownpower.
Keep hopper free from foreign bodies (bags, tools, miscellaneous), as they could damage
theoperationsortheoperator.
Generallyfertilizersarecorrosive.Forthisreason,itisimportantthatanyparticlesoffertilizer
NOTstayinthemachineforalongperiodoftime.
Cleanthehopperandthedistributoraftereachuseofthemachine.
If during cleaning operations air or water with pressure are used, it is necessary to wear
glassesandsafetymasksandkeepawaypersonsoranimalsfromthemachine.
Before connecting the machine to the vehicle check that this is in good conditions and that
brakesworkcorrectly,especiallyifyouworkonslopinggrounds..
Disconnect the spreader from vehicle only on level ground (with empty hopper), checking
thatthemachineisstable.
WARNING WARNING
During transport operations, stocking and deployment of the fertilizers. The operator must
follow all the label instructions and particularly to the content of the written risks and the
precautionsuggestions.
6

ATTENTION ATTENTION
The Manufacturer is not responsible for damages caused by an improper and unforeseen use
ofthemachine.
TheManufacturerisnotresponsiblefor:
Improperuseofthemachine,usebyuntrainedstaff;
Seriousdeficienciesintheforeseenmaintenance;
Changesornotallowedmodifications;
Useofnon-originalorspecifiedspareparts;
Failuretofullyorpartiallycomplywiththeinstructions;
Failuretocomplywiththecommonsafetyrulesduringwork;
Unusualcases.
ATTENTION ATTENTION
Thehitchpointofthevehicleandthespreadermustcoincideormustbeadapted.
Makesurethatthespreadercoupler is engaged in right way after every linkage operation of
themachineandthatitdoesnotcomeuncoupled.
Connectionofthemachinetothevehicle. Connectionofthemachinetothevehicle.
ATTENTION/DANGER ATTENTION/DANGER
The presence of the spreader can influence the maneuverability of the vehicle, in particular
duringtransport.
ATTENTION ATTENTION
Donotcome, for anyreason,betweenthevehicle and thespreaderwhenthevehicle engine is
running.
ATTENTION/DANGER ATTENTION/DANGER
Movementof thespreaderat highspeedscan causedamageto thespreaderand/orpersonal
injury.Alwaysmovespreaderatspeedssafeforcontrol.
Make a check of the vehicle and spreader before switching it on. Start to work only if the
machineisinperfectcondition.
Beforeusingthespreader,pleasebesurethatallthesafetydevicesarecorrectlyplacedand
in good condition; in case of breakdowns or damages to the protections, please replace
themimmediately.
Operation of the machine:
ATTENTION ATTENTION
During operation, please be sure that there are not any people or animals within a 50 ft. radius
ofspreader.Whenyou work in proximity of roads or publicplaces,it is absolutely necessary to
keepasafedistancefrompeopleandtoincreasetheprecautions.
ATTENTION ATTENTION
Anybody who comes up to the machine while under power is in a danger area. The operator
must prevent anybody from coming into the danger area and work under maximum caution. If
somebodycomesup,stopimmediately.
Beforeeveryuseofthecentrifugalspreader,pleasealwayscheckthewearofthevanesand
ofthespreaderdisc.Checkthatallthefastenersareinandtight.
Themachinemustneverbeunattendedwhenitismoving.
Alwayskeepthemachineingoodoperatingconditionsandprovideregularmaintenance.
ATTENTION ATTENTION
Spreaderisnotmeantfortransferoverroads.
DoNotoperate“OffroadUseOnlyVehicles”onpublicroads.
7

Forconnectionofthespreadertothevehicle,followthesesteps:
With vehicle and spreader on level ground, back vehicle in front of spreader and shut-off
engineandsetparkingbrake.
Note:itisnecessarytohavea1-7/8”ballonthebackofthetowvehicle.
Makesurehopperisempty,liftcouplingandsetontotowballofvehicle.
Note:usetwopeopleifnecessarytomakealignmenteasier.
Latchcouplerontoball,check to makes sure latching mechanism is holding tight and is fully
inlatchedposition,ifnot,adjustcouplersoattachmentiscorrect.
Hitchcouplerarmshouldbelevelwithin2°ofhitch,ifnot,correcthitchheightonvehicle.
Finally check all connections including ball mount, coupler, and for security add pin to
couplerlock.
Connection Connection
1.
2.
3.
4.
5.
ATTENTION ATTENTION
Alwaystestthekg/hathatyouwishtospreadbeforestartingwork
Use a fertilizer or other material in perfect conditions: humid material may not spread
uniformlyorcorrectly
Avoidspreadingduringwindydays,toimproveuniformdistribution.
The spread material must always be stored properly to maintain its physical properties, do
notkeepmaterialinhopperforlongperiodsoftime.
It is necessary to determine the speed of the centrifugal spreader, before starting the
operation of distribution, to stay within possible limits and try to keep consistent for the
durationofthespreadarea
Improperlevelingofspreadercancausepoorspreadingaswellaspoortrailercontrol.
SpreaderUse SpreaderUse
Recommendationsforcorrectdistribution. Recommendationsforcorrectdistribution.
NOTE:it isnotpossibletohave anexact spreadingchart forspreadersusingcentrifugal
force for spreading, given that the distribution quantity depends on the feed speed,
radius of distribution, humidity, size and weight of material, and the roughness of the
terrain.Thespreading chart containsgeneralinformation and isnotto be relieduponas
accurate settings but as a starting point for near perfect conditions, in order to
determine the quantity of spread in the field, settings must be completed by an
experiencedandcompetentoperator. 8

In order to assure equal distribution on both sides of the spreader, depending on the different
material specifications, the distributor vanes can be adjusted into varying positions by simply
removingthefrontscrewandturningvane,reinstallscrew.
When all the vanes are in the 1st position, the distribution is increased towards the left,
compared to the way the vehicle is moving. If the vanes are put in the last position the
distributionisincreasedtotheright.
Note: moving the vanes from 1st to last position, moving at the same speed, will affect
thedistributingwidthofthespreadmaterial.
Howtoadjustthespreadervanes Howtoadjustthespreadervanes
Reposition vane hole to change
spread throw.
Howtoadjustthespreading Howtoadjustthespreading
The spreading is regulated through the use of the levers that move the adjustable tray open or
closedatthebottomofthehopper,dependingontheamountofmaterialrequiredforoperation.
In order to set the regulation, after consulting the spread chart and all the manufactures
recommendation from the spread material, it is necessary to move the lever along the
graduatedscale.
WARNING WARNING
It is important that an experienced and competent operator verifies the correct amount of
spread,overuseofsomefertilizersmaydamagefields.
2
In order to spread from both sides lever (2) needs to be
positioned so both openings through hopper are open. To
spread to the left or right only, lever 2 needs to be
positionedtoallowmaterial toflow throughcorresponding
openinginhopper.
HopperLoad HopperLoad
Itisadvisedtousehelpwhenloadinghopperasbagsareheavy.
Do not set bags on top of hopper while transporting spreader to field as they may fall from
spreaderorcompressmaterialmakingitdifficulttospread.
9