KOMPAN PLAY360 User manual

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
1/19
PLAY360
A-xxxxx
X-xxxxx
xxxxxx xxxxxxxxxxxx xxxxxxxxx
-------- ------------------ ----------------------------
1 xxxxxxxx xxxxxxxxxx
1 xxxxxxxx xxxx
1 xxxxxxxx xxxxxxxxxx
1 xxxxxxxx xxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxx
1 xxxxxxxx xxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx
Quantity xxxxxxxx xxxxxxxxx
-------- ------------------ ------------------------------
1
xxxxxxxx -xx xxxxxxxxxxxxxxxxxxxxxx
1
xxxxxxxx -xx xxxxxx
1
xxxxxxxx -xx xxxxxxxxxxxxxxxx
2
xxxxxxxx -xx xxxxxxxxxxxxxxxxx
4
xxxxxxxx -xx xxxxxxxxxxxxxxxxxx
1
xxxxxxxx xx xxxxx
1
xxxxxxxx xx xxxxxxx
1
xxxxxxxx xx xxxxxxxxxxxxxx
1
xxxxxxxx xx xxxxxx
1
xxxxxxxx -xx xxx
3
xxxxxxxx -xx xxxxxxxxxx
xxxxxxxx xxxxxxxxxxxxxxxxxxxx
E-xxxxx
02
1,5
1
Installation of KOMPAN ELEMENTS structures
These instructions describe installation of
KOMPAN FUNKY ELEMENTS structures.
IMPORTANT!
Please read these instructions before beginning installation.
In addition to these general instructions you will find assembly
instructions, isometric views, post layout drawing etc. in the
Instruction Manual.
All the packages are furnished with labels carrying reference numbers.
Use the list of packages to check that all the packages are present
before starting installation.
Then check the contents of each box using the list of contents, which
you will find inside the top of the box.
2 Tools
The following tools are required for installation:
Tools for digging:
Shovel
Spade
Posthole digger
Tamping bar
Other tools:
Measuring tape *)
Stepladder
Bubble level
Drill set
4" C-clamp
Socket wrench set with extension *)
Rubber mallet
Hexagon key set *)
Drilling machine
Bits set (Torx and Phillips)
Bit adaptor
Knife
Screwdriver
Torque wrench
Clamp
*) metric

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
2/19
ill. 1
ill. 2
ill. 3
ill. 5
8
88
3
How to get started
Start by locating the footings and check that the
necessary space, including the safety zone, is available.
Make sure to allow for the recommended use zones
around all play activities on the structure, please see
Safety Zone Plan Drawing (ill. 1) at the end of the
Instruction Manual.
Placing the structure on the site
Identify the exact location of the play structure on the
site by arranging the floor frames in their respective
positions. Refer to the Post and Floor Layout Drawing
(ill. 2) at the end of the Instruction Manual.
If there is a slide it should turn away from the midday
sun in order to avoid overheating (ill. 3).
Protective surfacing material
Make sure to allow for resilient surfacing according the
safety standards EN 1176 (EU) or ASTM 1487 (USA),
see ill. 5 (R = thickness of surfacing material chosen).
Surface installation
For surface installation a layer of concrete of 140 mm (5.51")
is required to fasten expansion bolts, see ill. 4. Also please
see the relevant assembly instructions for play activities in
the Instruction Manual.
Footing holes for in-ground installation
Dig holes for posts, see ill. 5., indicating which activities
require concrete.
Please note: Do not fill the holes until assembly is complete
and the entire structure is plumb and level.
ill. 4
400317
90 mm
3,54"
ø12 mm
0,47 "
140 mm
5,51"
400317 - 12 mm:
Assembly of post footing for surface installation (ill. 7)
The KOMPAN ELEMENTS surface footing consists of a steel footing profile with 3 wedge
grooves, 3 long aluminium wedges with 3 holes, 3 short aluminium wedges with 2 holes,
and a flange unit.
- Insert the footing profile into the flange, then position the 3 short wedges in the wedge
grooves so that they are flush with the upper edge of the flange and the holes in the
flange and wedges line up. Insert the 8x20 mm screws 910820 in the wedges and
tighten the uppermost and lowermost screws alternately until both are fully tightened
and the footing section has expanded so that it is properly lodged in the flange unit.
- Then insert the long wedges in the wedge grooves so that the wedge ends with 2
holes are opposite the flange. Allow the footing unit to slide into the post so that all six
threaded holes in the wedges are visible through the holes in the sides of the post.
- Then slide six 10x20 mm button head screws 601020-A2 into the wedges.
- It is now possible to adjust the footing unit by loosening the button head screws. Tap
lightly on the screw heads to loosen the wedges from the grooves, adjust the footing
unit to the required position and tighten the screws.
4 Preparing the installation
Assembly of post footing for in-ground anchoring (ill. 6)
The KOMPAN ELEMENTS in-ground footing consists of a steel footing profile with 3
wedge grooves and 3 aluminium wedges that lock in place in the wedge grooves
using set screws. The function of the set screws is to retain the wedges in the wedge
grooves until the footing profile has been installed in the post. The footing is
adjustable and is designed for in-ground anchoring from 70 to max. 90 cm. For
in-ground anchoring of up to max. 120 cm A400441-99 is available.
- Slide the footing unit into the lower end of the post (the part with 6 holes) until
the threaded holes in the wedges are visible through the corresponding holes
in the sides of the post.
- Then insert six 10x20 mm button head screws 601020-A2 into the wedges and
the set screws can now be loosened.
- It is now possible to adjust the footing unit by loosening the button head screws.
Tap lightly on the screw heads to loosen the wedges from the grooves, adjust
the footing unit to the required position and tighten the screws.
90 cm
A400470-51
A400295-128
10x12
911012
120 cm
A400471-51
A400469-51
M10x20
601020-A2
ill. 6
ill. 7
40 cm
A400477-51
A400312-128
A400306-51
A400307-51
M8x20
910820
10x20
601020-A2
A400295-128
Top of safety surface

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
3/19
Assembly of post footing for surface installation (ill. 7)
The KOMPAN ELEMENTS surface footing consists of a steel footing profile with 3 wedge
grooves, 3 long aluminium wedges with 3 holes, 3 short aluminium wedges with 2 holes,
and a flange unit.
- Insert the footing profile into the flange, then position the 3 short wedges in the wedge
grooves so that they are flush with the upper edge of the flange and the holes in the
flange and wedges line up. Insert the 8x20 mm screws 910820 in the wedges and
tighten the uppermost and lowermost screws alternately until both are fully tightened
and the footing section has expanded so that it is properly lodged in the flange unit.
- Then insert the long wedges in the wedge grooves so that the wedge ends with 2
holes are opposite the flange. Allow the footing unit to slide into the post so that all six
threaded holes in the wedges are visible through the holes in the sides of the post.
- Then slide six 10x20 mm button head screws 601020-A2 into the wedges.
- It is now possible to adjust the footing unit by loosening the button head screws. Tap
lightly on the screw heads to loosen the wedges from the grooves, adjust the footing
unit to the required position and tighten the screws.
4 Preparing the installation
Assembly of post footing for in-ground anchoring (ill. 6)
The KOMPAN ELEMENTS in-ground footing consists of a steel footing profile with 3
wedge grooves and 3 aluminium wedges that lock in place in the wedge grooves
using set screws. The function of the set screws is to retain the wedges in the wedge
grooves until the footing profile has been installed in the post. The footing is
adjustable and is designed for in-ground anchoring from 70 to max. 90 cm. For
in-ground anchoring of up to max. 120 cm A400441-99 is available.
- Slide the footing unit into the lower end of the post (the part with 6 holes) until
the threaded holes in the wedges are visible through the corresponding holes
in the sides of the post.
- Then insert six 10x20 mm button head screws 601020-A2 into the wedges and
the set screws can now be loosened.
- It is now possible to adjust the footing unit by loosening the button head screws.
Tap lightly on the screw heads to loosen the wedges from the grooves, adjust
the footing unit to the required position and tighten the screws.
90 cm
A400470-51
A400295-128
10x12
911012
120 cm
A400471-51
A400469-51
M10x20
601020-A2
ill. 6
ill. 7
40 cm
A400477-51
A400312-128
A400306-51
A400307-51
M8x20
910820
10x20
601020-A2
A400295-128
Top of safety surface

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
4/19
50 cm
A400316-51
10x20
601020-A2
10x20
601020-A2
A400295-128
A400295-128
A400115-9906
911012
ill. 8
A400115-9906
Preparing the installation (continued)
Post assembly
When installing structures with platform heights of 240 cm or more, it is necessary to combine 2 posts into
one longer post. Use A400115-9906 as extension, which is provided with 6 holes with 12 mm diameter for
assembly of the footing A400xxx and the connector unit A400316-51.
The assembly is made by sliding the 6 wedges A400295-128 into the profile A400316-51.
Then insert the profile with wedges into the post extension A400115-9906 and fix the button
head screws 601020-A2.
Now slide this unit into the post at the opposite end and fix the button head screws 601020-A2 - see ill. 8.

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
5/19
Preparing the installation (continued)
Post preparation
Straps and secondary connectors along with the rubber-coated posts and the floor frames are the fundamental
components of the KOMPAN ELEMENTS system.
To save time and effort later it is very important to install each strap in the correct location with the correct
number of secondary connectors.
The Post Preparation Sheet (ill. 9-1) at the end of Instruction Manual is used to configure each post with straps
and secondary connectors. This sheet shows the correct placement of each strap as well as the required number
of secondary connectors to be added.
Grooves (rings) are moulded into the rubber layer of the posts at 100 mm intervals. These are used when placing
straps and secondary connectors at the specified heights.
Install secondary connectors on the straps before the straps are placed on the post - see ill. 10.
ill. 10
Strap
A400208-52
Secondary
connector
A400203-52
Example from Post Preparation Sheet
indicating placement of straps as well
as the number of secondary connectors
on each strap.
Post ID no. from
Post and Floor
Layout Drawing
Post ring no. 21
Indicates that a
strap is placed at
the twelfth ring on
this post
Total number of
secondary
connectors to be
placed on the strap
at the eleventh
ring on this post
Secondary connector
A400203-52
Strap
A400208-52 P1
1
3
4
5
6
7
8
9
10
11
12
2
Height of post
ill. 9-1
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
6/19
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
POST 8 (P8) 2400 mm
Straps Loc. Qty
Ring 30
Ring 29
Ring 20 1 0
Ring 19
Ring 18
Ring 17
1 0
Ring 16 1 0
Ring 15 1 0
Ring 14 1 0
Ring 13 1 0
Ring 12 1 0
Ring 11 1 0
Ring 10 1 0
Ring 9
Ring 8
Ring 7
Ring 6
Ring 5
Ring 4
Ring 3
Ring 2
Ring 1
1 0
Sub-total
Straps
Sub-total
2nd Conn.
11 3
Ring 28
Ring 27
Ring 26
Ring 25
Ring 24 1 0
Ring 23
Ring 22
Ring 21
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
2nd Conn.
M 8x40
210100408040 M 8x30 (black)
210100408030
Secondary connectors
Strap
2.
1.
ill. 11
Post ID no. from
Post and Floor
Layout Drawing
8
ill. 9-2
Preparing the installation (continued)
The Post and Floor Layout Drawing at the end of the Instruction Manual
assigns each post with a unique identification number, for example P8,
referring to the Post Preparation Sheet (ill. 9-2).
A sheet of self-adhesive numbers has been provided with each structure
and we recommend that you place the specified number on each post to
make assembly easier.
Connections for straps and secondary connectors
Bolts for straps and secondary connectors - see ill. 11.
IMPORTANT!
Always use 8x40 mm bolts 210100408040 in the threaded part of the strap
- see ill. 11 fig. 1 - and always use this connection first.
Always use 8x30 mm bolts (black) 210100408030 in the secondary connectors
- see ill. 11 fig. 2.
Bolts must remain finger-tight only, until all connections have been installed.

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
7/19
PT 6x14
320600506014
A400502-06 (60 )
A400503-06 (90 )
A400501-06 (45 )
2
5
Assembly order
Getting started
Post / floor frame assembly (ill. 12)
Floors come in various shapes and sizes, see the diagram on the last page.
Choose a fixed starting point when you begin assembling the floors. This could be any floor, but we
recommend that you choose either the highest or the lowest floor.
- Select the floor frame with the specified shape and size - see Post and Floor Layout Drawing, and
install the specified post on the frame. The easiest way to do this is to set the floor frame on edge
and then place the post in the floor frame mounting bracket at the correct position/height, i.e. when
the chosen floor height is 1000 mm the floor frame is to be installed on rings no. 9 and 10 on the post.
- The posts are configured as described under Preparing the installation and therefore the correct number
of straps will be provided for the assembly on the specified rings of the post, ill. 12.
- Now loosely attach the bolts and washers - always starting by using 8x40 mm bolts in the threaded part
of the strap and (if there are several connections at one level/ring) use 8x30 mm bolts in the secondary
connectors. Do not tighten the bolts, otherwise it will be impossible to install the adjoining floor frames.
- All posts are connected to the floor frames as described above.
- Then put this part of the structure to an upright position and place it correctly according to the plan.
- Now the adjoining floor frames at the same level, or at other levels, are installed and then their respective
posts, etc.
- When the adjoining floor frame has been installed, the previous floor frame is re-tightened.
Before re-tightening floor frames, always remember to place a plug at the bottom of the floor frame
mounting bracket, ill. 12 (2).
When installing floor frames at the same level, a 4" C-clamp, see ill. 13, may come in handy in order to hold the
new frame in position and thus avoid gaps.
IMPORTANT! Prior to the installation of each floor frame, don't forget to check that posts are plumb and floor
frames are level. It is also possible to adjust the footing.
ill. 12
M8x40
210000408040
Post
Strap Footing
1
Floor
frame
ill. 13
M8x16
321301008016

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
8/19
1
23
M8x40
210100408040
PT 6x14
320600506014
A400503-06
ill. 14
12
3
4
5
Assembly order (continued)
Assembly order for tall FUNKY ELEMENTS structures
- First attach the two tallest posts to the floor frame in the longitudinal direction.
Then raise the assembled unit to an upright position and prop it up. Attach the next two posts to
the floor frame.
If the structure includes several floor frames, posts are now assembled with the adjacent floor frame,
and the unit is then raised to an upright position and assembled as described above.
Please note: Local regulations concerning this type of work should be observed.
M8x16
321301008016

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
9/19
ill. 15
Assembly order (continued)
- Repeat the steps above until all posts are attached to the floor frame. Make sure that all straps
remain in their correct positions on the posts.
- The assembled unit of posts and floor frame may be picked up and placed into the correct footing
holes, or, in case of surface installation, in the correct position. This unit is the starting point of the
following assembly.
Please note: Tighten all bolts in the structure when all floor frames are installed.
Installing floor step foundation (see ill. 15 ):
The lowest floor (400 mm) will often be the floor step.
In this case foundation for surface installation or for
in-ground installation is added.
Surface installation
In-ground installation
A209029-99
A209025-60
A209026-51 400315
10x65 MB
210065
702530
A400783-51
A700703-51
M8 x 30 (black)
210100408030
A400468-52 (90o)
400010-A2
A10086-18
A10085-18
10x35 BB
110035-A2
B400144-0406
1
2
3
M8x40
210100408040
PT 6x14
320600506014
A400503-06
M8x16
321301008016

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
10/19
Assembly order (continued)
Installing floors to frames
- Place the floor onto the floor frame.
- Install the floor cover that fits the size of the floor corner.
- Please note that threaded bushings are already installed in the upper part of the floor frame. The 8 mm
bolts are to be installed either in these, see ill. 16, or directly in the groove in the floorplate, see ill. 17.
ill. 16 ill. 17
M8 x 30 (black)
210100408030
M8 x 30 (black)
210100408030
A400466-52 (45o)
A400467-52 (60o)
A400468-52 (90o)

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
11/19
Assembly order (continued)
Installing infill panels
- The infill panel, which is to be installed between platforms at different levels, is crucial to the stability and
strength of the structure. Consequently it is of the utmost importance to install this component, using all
the specified fasteners and ensuring careful tightening.
- First insert T-track bolts at the top floor frame and lock them, using T-track locks. Then insert the infill
unit as shown in ill. 18 by use of the specified hardware. Finally insert T-track bolts at the bottom floor
frame - bolts should be put through the oblong hole at the bottom of the infill unit.
- Re-tighten all nuts and install Do-Nut caps.
ill. 18
A400742-51
A400743-51
400210
A10078-13
A900270-06
10x30 MB
210030
A10078-13
A10080-06
M8x20
121000608020
A400526-06
A62105-06
400108
A400278-52
A62106-52
M8x20
121000608020
1
3
2
4
A62102-06
A62105-06
400108
A400278-52
A62106-52
A62102-06

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
12/19
Assembly order (continued)
Installing wall panels
First install the wall brackets onto the posts:
Installation of wall brackets: Wall brackets may
be attached to a strap or to a secondary connector,
see ill. 19 which bolts to use.
IMPORTANT!
Do not tighten connections nor install the plastic
cover for wall bracket until all panels have been
installed.
ill. 19
321300708020
Fitting for wall panel
A400504-06
Fitting for wall panel
A400504-06
A400505-xxx
ill. 20
Installing upper wall panels (ill. 20): Four wall brackets are used to support an upper wall panel.
- Panels are attached to the wall bracket using a fitting for wall panel, a washer and an 8 mm self-locking nut.
- Some types of panels are provided with a centre mounting hole. This hole is not used for fastening
if the panel is placed as upper panel. In that case the hole is to be covered with fittings for wall panel,
washers, bolt and nut, see ill. 20 (C).
321300708020
400108
A400505-xxx
321300708020
A400505-xxx
Fitting for
wall panel
A400504-06
M8x40
210100408040
A400508-06
Wall bracket
A400207-128
A400508-06
M8x30 (black)
210100408030
For secondary connectors:
For straps:
C
M8x30
210100408030
M8x30
210100408030

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
13/19
A10086-06
A400278-52
400108
A10085-06
M8x25
121000608025
A400526-06
ill. 21
M8x55
210100408055
M8x40
210100408040
A400217-128
A400214-128
M8x30 (BLACK)
210100408030
ill. 22
Assembly order (continued)
Installing steel panels
First install the wall brackets onto the posts.
Installation of wall brackets: Wall brackets may be
attached to a strap or to a secondary connector, see ill. 21
which bolts to use.
The top of the steel panel is attached to the wall bracket
using a wall bracket fitting and an 8x50 mm bolt, see ill. 21.
The bottom of the steel panel is attached by inserting
T-track bolts in the floor frame and lock them with T-track locks.
Then fasten the steel panel with the specified hardware,
see ill. 22.
For secondary connectors:
For straps:

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
14/19
ill. 23
ill. 24
A400508-06
A400508-06
For connectors:
A400426-66
A400426-66
M8x30 (BLACK)
210100408030
For straps:
M8x40
210100408040
A10086-06
A10085-06
210100408030
A400278-52
A400872-51
Assembly order (continued)
Installing wall panels
First install the wall brackets onto the posts:
Installation of wall brackets: Wall brackets may
be attached to a strap or to a secondary connector,
see ill. 23 which bolts to use.
IMPORTANT!
Do not tighten connections nor install the plastic
cover for wall bracket until all panels have been
installed.
Installing upper wall panels (ill. 24): Four wall brackets are used to support an upper wall panel.
- Panels are attached to the wall bracket using a M8x30 bolt (210100408030), en washer (A400278-52)
and a tropic nut (A10086-06 + A10085-06), see ill. 24.

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
15/19
LE42000000
Copyright © KOMPAN A/S 1/2
VLE42000000 20031127 AB
M8x50
210100408050
M8x40
210100408040
A400217-128
A400214-128
A400283-52
A400533-9912 (YEL)
A400533-99129 (RED)
1
red
rot
rouge
rojo
rosso
rood
röd
rød
YEL: yellow
gelb
yellow
amarillo
giallo
geel
gul
gul
RED:
M8x30 (BLACK)
210100408030
black
schwarz
noir
negro
nero
zwart
svart
sort
BLACK:
LE400502-3418
1/3
VLE4005023418 20030902 AB
Copyright © KOMPAN A/S
55 cm
1'-10"
14 cm
6"
52 cm
1'-8"
52 cm (1'-8") - R = F
F
R
Variable*
Resilient
Surface
175 cm
5'-9"
ill. 25
LE416200
LE420000
LE422000
LE421900
LE422200
LE422700
LE400502
Installation of play activities
Use the installation instructions provided for each play activity in the Instruction Manual.
All play activities for the specific structure appear from the Activity Identification Drawing (ill. 25)
in the Instruction Manual.

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
16/19
6 Final procedures
Final assembly check
- The entire play structure is tightened securely and panels and play activities double-checked
for correct installation.
- Make sure that the entire structure is plumb and level.
Footing
- The footing holes for posts and activities should be back-filled with compacted soil or concrete
as specified in the play activity instructions.
Surface installation
- The footing is fastened into the concrete as specified in the play activity instructions.
ill. 26
Protective surfacing
A resilient protective surfacing must be installed in accordance with the safety standards EN 1176 (EU)
or ASTM 1487 (USA).
Installation of post caps
IMPORTANT! Post caps and all other safety covers should be installed only after the final assembly
inspection has been completed and all fasteners have been tightened securely.
Post caps (A400592-xx + A400593-xx) must be placed on all exposed post ends (ill. 25).
A400593-XXX A400592-XXX

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
17/19
A100-42
A10089-18
Final procedures (continued)
Do-Nut cap installation
Finish the installation by removing all labels and install all Do-Nut caps and protective covers.
Make sure they snap into place.
Two special marking Do-Nuts with transparent caps are supplied with the structure together with a sheet
of labels with addresses of the supplier of each country.
One of the caps is already provided with a label from the factory with information of the product ref.no. as
well as the week and year of production.
The other cap should be provided with the
address label of the specific country.
Both these Do-Nuts with labels should be placed
on the product according to the safety standards
EN 1176 (EU) and ASTM 1487 (USA).
Example of how to place a marking Do-Nut (NB!!) as shown in
the Isometric View at the back of the Instruction Manual.
IMPORTANT!
The playground must not be used until installation is complete and it has been inspected with protective
surfacing, and all concrete must be set.
NB!!
90o
NB!!
2
3
1

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
18/19
Panel 11
A400011
Panel 2
A400002
Panel 4
A400004
Panel 3
A400003
827,3 mm
7
Overview of main components
Square floor
Floor: B400007
Frame: A400464
X-large floor
Floor: B400102
Frame: A400704
Floor step
Floor: B400144
Frame: A400783
Large floor 90° arc
Floor: B400003
Frame: A400462
Large floor 90°
Floor: B400001
Frame: A400459
827,3 mm
1170 mm
827,3 mm 827,3 mm
827,3 mm

PLAY360
Copyright©KOMPAN A/S
V00050GB 20140814 RikBon/PetrJu
19/19
Overview of main components (continued)
Post (height) Product number
400 mm A400100-9906
600 mm A400101-9906
800 mm A400102-9906
1000 mm A400103-9906
1200 mm A400104-9906
1400 mm A400105-9906
1600 mm A400106-9906
1800 mm A400107-9906
2000 mm A400108-9906
2200 mm A400109-9906
2400 mm A400110-9906
2800 mm A400116-9906
3000 mm A400111-9906
1000 mm A400115-9906