Konica Minolta BIZHUB PRO 920 User manual

For detail information，Please refer to the User Manual
bizhub PRO 920
Shortcut Manual

1
PRO 920 Shortcut manual
Power ON
To power on, please turn on the Main Switch ，and then the Sub Switch
Power OFF
To power off，please turn off the Sub Switch，and then the Main Switch (Please wait 10
seconds before restart the machine)
Warm-up takes aprox. 5.5 minutes. the machine will display message ”Ready to copy”
after the warm-up process completed.
Sub Switch
Main Switch
Meter

2
Replace Toner
When Please add toner or this signal appears,
Please replace the toner

3
Place the original on the document feeder (max 100 sheets 80g/㎡
㎡㎡
㎡, face up), or using
original glass (face down)
Separate Scan
Use the original glass to scan original unsuitable for the document feeder
1. Touch Separate Scan
2. Position originals, then press Start
-Using original glass:
Place original FACE DOWN, starts scanning from the first page, then repeat for all
originals
-Using ADF:
Position original FACE UP, if number exceeding 100 sheets, divides them into blocks.
3. After scan, touch Complete scan and press start

4
Change Paper Size
The capacity of the manual feed tray is 150 sheets (80g/㎡
㎡㎡
㎡)
1. Touch Basic, and Paper
2. Choose manual feed tray, and touch Bypass Setting
3. Choose suitable paper (Thick, Thin, OHP Paper)
4. For custom size input, touch Custom
5. Input the length X and width Y
6. Touch Ok
Density Adjustment
1. Touch Basic, and Density
2. Choose Lighter or Darker to adjust

5
Zoom
1. Touch Basic, and Zoom
2. Touch desired ratio or touch XY Zoom to change the zoom ratio by input 4 digit ratio
3. Touch Ok to confirm

6
--Simplex / Duplex
Touch Simplex / Duplex
Can choose
a. Single side original to double side copy 1 2
b. Double side original to single side copy 2 1
c. Double side original to double side copy 2 2

7
Combine Originals
Lay out 2 pages (2in1)，
，，
，or 4 pages onto one sheet (4in1)
Touch Combine Originals
Choose 2in1，4in1
Special Orig.
1. Touch Combined Original
2. Touch Special Original
3. Touch Mixed Original
Bind
1. Combined Original
2. Touch Bind
Choose different binding direction
For example Left
Original Size
1. Touch Combined Original
2. Touch Original Size
3. Touch Custom Size
4. Choose different size for the original,
Or choose Full Area
Orig. Image Type
Choose different original type
Choose Dot Matrix for pencil written original

8
Application
Sheet / Cover /Chapter Insert
1. Touch Application
2. Touch Sheet /Cover /Chapter Insert
3. Touch Insert Sheet
4. Touch Front Cover
5. Touch Cover/Print for (Simplex/Duplex) or image setting
6. And choose the tray of the inserted paper
7. Touch Ok
8. Touch Start
For page insertion, please repeat step 1-3
1. Touch Insert Paper
2. Touch Page Setting to input location
of page insertion
3. Use “,(comma)” for between pages or
“-(hyphen)” for consecutive pages
4. Choose Fix after finished input
5. Choose which tray for the page
insertion
6. Touch OK
7. Touch Start

9
Insert Image
1. Touch Application
2. Touch Sheet /Cover /Chapter Insert
3. Touch Insert Image
4. Input page number, after each input,
touch Set
5. After input the insert page number, touch OK
6. Place the original on the document feeder, touch Start
7. After finished all pages, place the insert original on the document glass, touch Start
8. When finished scanning all insert image,
touch Complete Scan
9. Touch Start
Program Job
1. Touch Application
2. Touch Sheet /Cover /Chapter Insert
3. Touch Program Job
4. Touch OK
5. Choose the copy setting
6. Touch Start
7. Touch Fix
8. Finished scanning the document, touch Fix
9. Touch Separate Scan
10.Touch Start