Konica Minolta Accurio Label 190 Original instructions

Accurio Label 190/bizhub PRESS C71cf Contents-1
Contents
1Introduction
1.1 Welcome .......................................................................................................................................... 1-2
1.1.1 Configuration and Usage of User’s Guides ....................................................................................... 1-2
1.2 Environmental Information............................................................................................................. 1-3
1.3 Legal Restrictions on Reproduction ............................................................................................. 1-4
2 Safety Information
2.1 Warnings and Precautions for Main Body.................................................................................... 2-2
2.1.1 Power Source Connection................................................................................................................. 2-3
2.1.2 Installation.......................................................................................................................................... 2-4
2.1.3 Using the Product .............................................................................................................................. 2-5
2.1.4 Consumables ..................................................................................................................................... 2-6
2.2 Warnings and Precautions for Roll Winder RW-101/Roll Winder RW-201 ................................ 2-8
2.2.1 General Information on Safety ........................................................................................................... 2-8
2.2.2 Warning Classification ....................................................................................................................... 2-8
2.2.3 Classification of Other Indications ..................................................................................................... 2-9
2.2.4 Safety Precautions............................................................................................................................. 2-9
2.2.5 Guidelines for Safety Usage (General) ............................................................................................. 2-10
2.2.6 Guidelines for Safety Usage (Paper Feeding/Winding).................................................................... 2-10
2.2.7 Guidelines for Safety Usage (Safety and Maintenance)................................................................... 2-10
2.2.8 Inspections before Power-on........................................................................................................... 2-10
2.3 Regulation Notices for Main Body............................................................................................... 2-11
2.3.1 Laser Safety ..................................................................................................................................... 2-11
2.3.2 Ozone Release................................................................................................................................. 2-12
2.3.3 Electromagnetic Interference and Safety Approvals ....................................................................... 2-12
2.3.4 Volatile Organic Compounds (VOC)................................................................................................. 2-13
2.4 Warning and Caution Labels on Main Body ............................................................................... 2-14
2.4.1 Caution Labels on Fusing Part of Fixing Conveyance Unit ............................................................. 2-14
2.4.2 Warning Label on Waste Toner Box ................................................................................................ 2-15
2.4.3 Warning Label for Generation of Volatile Organic Compounds....................................................... 2-15
2.4.4 Warning and Caution Labels on Paper Feed Section of Main Body ............................................... 2-16
2.4.5 Warning and Caution Labels on Paper Exit Section of Main Body ................................................. 2-18
2.5 Warning and Caution Labels on Roll Winder RW-101 ............................................................... 2-19
2.5.1 Warning Labels on the External Front of Roll Winder RW-101........................................................ 2-19
2.5.2 Caution Label on the Internal Front of Roll Winder RW-101 ........................................................... 2-23
2.5.3 Caution Label on the Inside of Paper Roll Cover of Roll Winder RW-101....................................... 2-24
2.5.4 Warning Label on the Internal Rear of Roll Winder RW-101............................................................ 2-25
2.6 Warning and Caution Labels on Roll Winder RW-201 ............................................................... 2-26
2.6.1 Warning Labels on the Exterior of Roll Winder RW-201.................................................................. 2-26
2.6.2 Warning and Caution Labels on the Internal Front of Roll Winder RW-201 .................................... 2-28
2.6.3 Caution Label on the Inside of Paper Roll Cover of Roll Winder RW-201....................................... 2-30
2.6.4 Warning Label on the Internal Rear of Roll Winder RW-201............................................................ 2-31
2.7 Operation Precautions for the Machine...................................................................................... 2-32
2.7.1 Power Source .................................................................................................................................. 2-32
2.7.2 Operating Environment .................................................................................................................... 2-32
2.7.3 Clothes for Operating the Machine.................................................................................................. 2-32
2.7.4 Storage of Printed Materials ............................................................................................................ 2-32
2.7.5 Ozone Release................................................................................................................................. 2-32
2.7.6 Direct Sunlight.................................................................................................................................. 2-32
2.7.7 Data Stored in This Machine............................................................................................................ 2-33

Contents-2 Accurio Label 190/bizhub PRESS C71cf

1Introduction

Welcome
1
1-2 Accurio Label 190/bizhub PRESS C71cf
1.1
1Introduction
1.1 Welcome
Thank you for purchasing this machine.
This User’s Guide provides precautions and requests that should be followed to ensure safe usage of this
machine. Please be sure to read this guide before using the machine.
Please keep this guide in a safe place where you can access them easily.
1.1.1 Configuration and Usage of User’s Guides
The following configuration of User’s Guides is provided for this machine.
When you want to learn about detailed functions or operation procedures, refer to the HTML User's Guide.
*: To obtain the Quick Guide and the HTML User's Guide, contact your service representative.
Note that basic technical knowledge about the machine is required to enable users to perform maintenance
work or troubleshooting operations. Maintenance and troubleshooting operations should be carried out as
instructed in these User’s Guides.
Should you experience any problems, contact your service representative.
Title of booklet manual Overview
Safety Information (This Guide) This guide provides precautions and requests that
should be followed to ensure safe usage of this ma-
chine.
Read this guide before using the machine.
Title of PDF manual Overview
Quick Guide* This guide describes the basic operations, how to
handle paper, and cleaning procedures of this ma-
chine.
Title of HTML manual Overview
HTML User's Guide* This guide describes the basic operations, functions
that enable more convenient operations, maintenance
procedures, simple trouble shooting operations, and
various setting methods of this machine.

Accurio Label 190/bizhub PRESS C71cf 1-3
1.2 Environmental Information 1
1.2 Environmental Information
Auto Low Power
Auto Low Power conserves energy by lowering the power consumption. The time period to activate this func-
tion can be set for --- minute, 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120
minutes, or 240 minutes. Power saving time periods, 90, 120, and 240 minutes, may not be displayed de-
pending on regions.
As default of Auto Low Power, [--- min.] is specified. Setting [--- min.] for Auto Low Power means that Auto
Low Power is disabled.
Setting [--- min.] (OFF) for Auto Shut Off automatically changes the Auto Low Power setting to [5 min.], and
then allows you to change it to another time, other than [--- min.].
When any option other than [--- min.] (OFF) is specified for Auto Shut Off, the time period for Auto Low Power
cannot exceed that for Auto Shut Off.
The highlighted indication of the time in Auto Low Power area goes dark when the same period of time as
that of Auto Shut OFF is selected. In this case, Auto Shut OFF functions instead of Auto Low Power.
Auto Shut Off
Auto Shut Off achieves further energy conservation by reducing power consumption. The time period to ac-
tivate this function can be set for --- minute, 1 minute, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or
240 minutes.
As default of Auto Shut Off, [1 min.] is specified. The touch panel display and LEDs other than the Power Save
and Power LEDs turn off lowering power consumption of the machine.
Setting [--- min.] for Auto Shut Off means that Auto Shut Off is disabled.
The time period for Auto Shut Off cannot be shorter than that for Auto Low Power.
ErP Setting
This is a function that turns the main power switch OFF when a certain period of time elapses with Auto Low
Power activated, Auto Shut Off activated, or the sub power switch turned OFF.
The time period to activate this function can be set for none (Do Not Switch), 12 hours, 24 hours, 36 hours,
48 hours, 60 hours, or 72 hours.
If the Weekly Timer ON/OFF Setting is set to [Weekly Timer ON], the [02 ErP Setting] key will be grayed out
to show inactivity.
We recommend that you utilize the Auto Low Power, Auto Shut Off, and ErP Setting functions.

Legal Restrictions on Reproduction
1
1-4 Accurio Label 190/bizhub PRESS C71cf
1.3
1.3 Legal Restrictions on Reproduction
Certain types of originals must never be reproduced with the purpose or intent to pass reproductions of such
originals off as the originals.
The following is not a complete list, but is meant to be used as a guide to responsible reproduction.
<Financial Instruments>
-Personal checks
-Traveler’s checks
-Money orders
-Certificates of deposit
-Bonds or other certificates of indebtedness
-Stock certificates
<Legal Originals>
-Food stamps
-Postage stamps (canceled or uncanceled)
-Checks or drafts drawn by government agencies
-Internal revenue stamps (canceled or uncanceled)
-Passports
-Immigration papers
-Motor vehicle licenses and titles
-House and property titles and deeds
<General>
-Identification cards, badges, or insignias
-Copyrighted works without permission of the copyright owner
In addition, it is prohibited under any circumstances to reproduce domestic or foreign currencies, or works
of art without permission of the copyright owner.
When in doubt about the nature of an original, consult with legal counsel.
NOTICE
This machine provides the forgery prevention function in order to prevent financial instruments from being
reproduced illegally.
We appreciate your understanding that printed images may infrequently have some noise or image data may
not be stored under certain circumstances due to this forgery prevention function.

2Safety Information

Warnings and Precautions for Main Body
2
2-2 Accurio Label 190/bizhub PRESS C71cf
2.1
2 Safety Information
2.1 Warnings and Precautions for Main Body
This section contains detailed instructions on the operation and maintenance of this machine. To achieve op-
timum utility of this device, all operators should carefully read and follow the instructions in this manual.
Please read the following section before connecting the machine to the supply. It contains important infor-
mation related to user safety and preventing equipment problems.
Make sure that you observe all of the precautions that appear in different sections of this manual.
KMI_Ver. 02_E
dReference
Some parts of the contents of this section may not correspond with the purchased product.
Warning and precaution symbols
Be sure to observe the safety precautions.
-This manual contains the instructions that should be strictly observed at all times to prevent injury to
yourself and other persons as well as damage to property.
Injuries and damage that might be caused by using the product improperly are classified according to the
following symbols.
These are some of major exemplary graphical symbols.
Pictorial indication Description
Improper handling can cause serious injury or death.
Improper handling can cause minor injury or damage to houses
and property.
Graphic
symbols
Description Graphic
symbols
Description Graphic
symbols
Description
General
Prohibited
Do not
disassemble
Do not touch
Instructions Ground/Earth Unplug from
outlet
General
precaution
High
temperature
Electrical
shock hazard

Accurio Label 190/bizhub PRESS C71cf 2-3
2.1 Warnings and Precautions for Main Body 2
2.1.1 Power Source Connection
Do not use any power cord other than the one supplied in the
package or attached on the products. If a power cord is not
supplied, use only the power cord and plug that are specified
in the user documentation. Failure to use this cord could re-
sult in a fire or electrical shock. If the power cord supplied in
the package cannot be used in the country where this prod-
uct was sold, use a power cord that meets the following con-
ditions or contact your Technical Representative.
• The power cord has voltage and current rating appropri-
ate for the rating plate on this machine.
• The power cord meets regulatory requirements for the ar-
ea.
• The power cord is provided with grounding pin/terminal.
Do not use the power cord to other products.
Failure to do that could result in a fire or electrical shock.
Do not scratch, abrade, place a heavy object on, heat, twist,
bend, step on, pull on, or damage the power cord. Use of a
damaged power cord (exposed core wire, broken wire, etc.)
could result in a fire or breakdown.
Should any of these conditions be found, immediately turn
OFF the power switch, unplug the power cord from the pow-
er outlet, and then call your authorized service representa-
tive.
Do not use the power source voltage other than being spec-
ified on the machine. Failure to do that could result in a fire or
electrical shock.
Do not use a multiple outlet adapter to connect any other ap-
pliances or machines. Use of a power outlet for more than the
marked current value could result in a fire or electrical shock.
Do not use an extension cord. Use of an extension cord could
cause a fire or electric shock. If the power cord furnished with
the product is not long enough to be plugged into a wall out-
let, contact your Technical Representative.
Do not unplug and plug in the power cord with a wet hand,
as an electrical shock could result.
Plug the power cord all the way into the power outlet. Failure
to do this could result in a fire or electrical shock.
Make sure to ground this product.(Connect the power cord
to an electrical outlet that is equipped with a grounding ter-
minal.) Failure to do so and an unlikely event of leakage could
result in a fire or electrical shock.

Warnings and Precautions for Main Body
2
2-4 Accurio Label 190/bizhub PRESS C71cf
2.1
2.1.2 Installation
The outlet must be near the equipment and easily accessible.
Otherwise you can not pull out the power plug when an emer-
gency occurs.
Do not place any objects around the power plug, as the pow-
er plug may be difficult to pull out when an emergency oc-
curs.
Do not tug the power cord when unplugging. Pulling on the
power cord could damage the cord, resulting in a fire or elec-
trical shock.
Remove the power plug from the outlet more than one time a
year and clean the area between the plug terminals. Dust that
accumulates between the plug terminals may cause a fire.
Keep this bag away from babies and children. Do not use in
cribs, beds, carriages, or playpens. The thin film may cling to
nose and mouth and prevent breathing. This bag is not a toy.
Do not place a flower vase or other container that contains
water, or metal clips or other small metallic objects on this
product. Spilled water or metallic objects dropped inside the
product could result in a fire, electrical shock, or breakdown.
Should a piece of metal, water, or any other similar foreign
matter get inside the product, immediately turn OFF the pow-
er switch, unplug the power cord from the power outlet, and
then call your Technical Representative or your authorized
service representative.
Make sure that the power cord is placed on a site in which no
person would step on or trip over it. Stepping on or tripping
over the power cord could heat the power cord, resulting in
a fire or electric shock.
<If instructed to use fixing legs>
When the product has been installed, fix the product using
the fixing legs. Not using the fixing legs could cause the prod-
uct to move or topple over.
Do not place the product in a dusty place, or a site exposed
to soot or steam, near a kitchen table, bath, or a humidifier.
A fire, electrical shock, or breakdown could result.
Do not place this product on an unstable or tilted bench, or
in a location subject to a lot of vibration and shock. It could
drop or fall, causing personal injury or mechanical break-
down.

Accurio Label 190/bizhub PRESS C71cf 2-5
2.1 Warnings and Precautions for Main Body 2
2.1.3 Using the Product
Do not let any object plug the ventilation holes of this prod-
uct. Heat could accumulate inside the product, resulting in a
fire or malfunction.
Whenever moving this product, be sure to disconnect the
power cord and other cables. Failure to do this could damage
the cord or cable, resulting in a fire, electrical shock, or
breakdown.
When moving this product, always hold it at the locations
specified in the User’s Guide or other documents. If the unit
is moved while held at locations other than those specified, it
may fall, causing severe personal injury.
Do not modify this product, as a fire, electrical shock, or
breakdown could result. If the product employs a laser, the
laser beam source could cause blindness.
Do not attempt to remove the covers and panels which have
been fixed to the product. Some products have a high-volt-
age part or a laser beam source inside that could cause an
electrical shock or blindness.
Do not keep using this product, if this product becomes inor-
dinately hot or emits smoke, or unusual odor or noise. Imme-
diately turn OFF the pow-er switch, unplug the power cord
from the power outlet, and then call your Technical Repre-
sentative or your authorized service representative. If you
keep on using it as is, a fire or electrical shock could result.
Do not keep using this product, if this product has been
dropped or its cover damaged. Immediately turn OFF the
power switch, unplug the power cord from the power outlet,
and then call your Technical Representative or your author-
ized service representative. If you keep on using it as is, a fire
or electrical shock could result.
Do not use flammable sprays, liquids, or gases inside or near
this machine. Do not clean the inside of this machine using a
flammable gas duster. A fire or explosion could result.
<If an RFID module (limited only to 13.56 MHz) for use in in-
side-the-machine proximity communication or electromag-
netic induction heating (IH) technology (limited only to 20.05
kHz to 100 kHz) is being used>
This machine generates a weak magnetic field. If you experi-
ence any unusual symptoms with your implantable medical
equipment (cardiac pacemaker, etc.) while near the machine,
move away from the machine and see a doctor immediately.
Please call your Technical Representative or your authorized
service representative if you do not understand the pur-
chased product corresponds or not.
<If a non-contact IC card reader is being used>
If you use an implantable medical equipment (cardiac pace-
maker, etc.), do not bring the IC card reader close from the
implant within 12 cm at all times. The radio waves may affect
implantable medical equipment (cardiac pacemaker, etc.)
operations.

Warnings and Precautions for Main Body
2
2-6 Accurio Label 190/bizhub PRESS C71cf
2.1
2.1.4 Consumables
Using this product in a poorly ventilated room for a long time
or producing a large volume of copies or prints may cause
the odor of exhaust air from the machine. Ventilate the room
well.
The inside of this product has areas subject to high temper-
ature, which may cause burns.When checking the inside of
the unit for malfunctions such as a paper misfeed, do not
touch the locations (around the fusing unit, etc.) which are in-
dicated by a “Caution HOT” caution label. A burn could re-
sult.
Unplug the product when you will not use the product for
long periods of time.
When using the machine, do not look at the light of the lamp
for a prolonged time. Eyestrain could result.
Do not use stapled paper, conductive paper (such as silver
paper or carbon paper) or treated heat-sensitive/inkjet paper,
otherwise a fire may result.
Do not throw toner or a container that contains toner (e.g.,
toner cartridge and developing unit) into an open flame. The
hot toner may scatter and cause burns or other damage.
Do not leave toner-related parts (e.g., toner cartridge and de-
veloping unit) within easy reach of children. Licking any of
these parts or ingesting toner could damage your health.
Do not store toner-related parts (e.g., toner cartridge and de-
veloping unit) near devices susceptible to magnetism, such
as precision equipment and data storage devices, otherwise
they may malfunction. They could cause these products to
malfunction.
Do not force open the toner-related parts (e.g., toner car-
tridge and developing unit). If toner tumbles from the toner
bottle, take utmost care to avoid inhaling it or even getting
skin contact.
If toner lands on your skin or clothing, wash thoroughly with
soap and water.
If you inhale toner, move to a place with fresh air and gargle
with a lot of water repeatedly. Should you get symptoms
such as coughing, seek medical advice.
If you get toner into your eyes, immediately rinse them with
running water for over 15 minutes. Seek medical advice if ir-
ritation persists.
If you swallow toner, rinse out your mouth and drink a few
glasses of water. Seek medical advice if necessary.
Never touch the electrical contacts of the units (e.g., toner
cartridge and developing unit), as an electrostatic discharge
may damage the product.

Accurio Label 190/bizhub PRESS C71cf 2-7
2.1 Warnings and Precautions for Main Body 2
Before handling, see the user documentation for the safety
information.
<If instructed to replace the fusing unit>
The fusing section is extremely hot. Before replacing the fus-
ing unit, be sure to open doors and covers of the machine.
Then, leave the machine to stand idle for a specified period
of time and make sure that the fusing section has cooled
down to room temperature. Failure to follow these instruc-
tions could result in a burn.

Warnings and Precautions for Roll Winder RW-101/Roll Winder RW-201
2
2-8 Accurio Label 190/bizhub PRESS C71cf
2.2
2.2 Warnings and Precautions for Roll Winder RW-101/Roll Winder
RW-201
This manual provides information necessary for the use of Roll Winder RW-101 and Roll Winder RW-201.
Read this manual thoroughly before use to ensure you understand how to use these units properly and use
them correctly.
Always keep this manual handy when working with the units. Also keep it in an easily accessible place for
future reference where it will not get dirty or damaged.
2.2.1 General Information on Safety
1 When transporting or installing the units, always wear safety shoes, and also working gloves (if neces-
sary).
2 When operating the machine, always wear safety shoes (with a protective steel toe cap), a safety cap
for head protection, and a jacket with buttons or fasteners on the front and with the gathered cuffs or
those which can be fastened with buttons. Always fasten the buttons and the fasteners properly.
3 To prevent the machine trouble, do not install the units in the following places:
• A place where the ambient temperature drops below 0°C (32°F) or exceeds 40°C(104°F)
• A place where the relative humidity drops below 30% or exceeds 80%, or where condensation oc-
curs
• A place subject to dust, salt, metal particles, or oily smoke
• A place where water, oil, or chemical substances may be splashed
4 The control panel is categorized “type 1 enclosure (for use in pollution degree 2).”
2.2.2 Warning Classification
Warning labels are used differently as follows depending on the situation in this manual and on the products.
Understand these labels thoroughly and follow the instructions described below.
The following safety precautions contain the preventive measures that shall be taken by users to avoid dan-
gers.
These labels shall be attached to the positions where users can always see and check the labels. When a
label has been peeled off or soiled, replace it with a new one.
Category Description
DANGER This label is used for the precautions and warning labels used
for the locations where there is a risk of danger that may lead
to the death or serious injury of an operator unless the danger
is eliminated.
WARNING This label is used for the precautions and warning labels used
for the locations where there is a potential risk of danger that
may lead to the death or serious injury of an operator unless
the danger is eliminated.
CAUTION This label is used for the precautions and warning labels used
for the locations where there is a risk of danger that may lead
to the minor injury or moderate injury of an operator unless
the danger is eliminated.
PROHIBITED
This label is used for the descriptions of the prohibited oper-
ations and actions. This label especially indicates the possi-
bility of the occurrence of a serious damage on this machine
and the possibility of the cases where users cannot take our
guarantee, maintenance, and service.
CAUTION This label is used for the instructions and guidelines about op-
erations and actions. This label especially indicates that this
machine may be physically damaged unless particular atten-
tions are given.

Accurio Label 190/bizhub PRESS C71cf 2-9
2.2 Warnings and Precautions for Roll Winder RW-101/Roll Winder RW-201 2
2.2.3 Classification of Other Indications
2.2.4 Safety Precautions
Safety precautions are described below.
-For the safety use of the machine, correct operations and periodic maintenance are essential. Read this
manual carefully beforehand. Never start printing or maintenance work unless you understand them
thoroughly.
-Always follow the operation methods, procedures and safety instructions in this manual. If you do not
follow them described in this manual, we do not take any responsibility for your safety.
-This manual also describes the items that may expose operators to danger or cause machine failures
and damages unless you follow them.
-Covers (safety covers) are installed for the dangerous driving parts of the machine and the parts where
operators may be caught by the machine. They are necessary for safety. Make sure to keep them at-
tached while the machine is operating. If any one of the covers is damaged, repair it immediately.
(Please contact your service representative or our customer engineer.) Never operate the machine until
the damaged cover is repaired.
-Do not alter or modify the machine unless we recommend to do so. When you desire any reconstruction
of the machine, contact us or your service representative. We do not take any responsibility for the re-
constructions we have no concern with.
-WARNING and CAUTION labels (safety labels) are attached to the locations where there is a risk of dan-
ger that may lead to an accident unless attentions are given. Follow the instructions on the labels when
you perform operations around the locations where the labels are attached.
-Never peel off any label. If any one of the labels has been peeled off, ask us or your service represent-
ative for a new label. Certainly attach the new label at the original position.
-When attaching a new one, remove oil and such on the location where the label goes in advance.
-Do not wipe the surface of safety labels with any solvent and such.
-When painting the machine, take extra care not to put paint on the labels.
-Clothes for operating the machine
- For the protection of your feet, put on safety shoes (with metallic protectors at the toes).
- Put on an outer wear with buttons or a zipper and always fasten the buttons or the zipper so that your
inner wears are not caught by the machine. Fasten buttons on wrists of the outer wear or tie off wrists
with bands.
-Operations without covers
- Unless there is a special hazard inside a part or component where a cover is mounted, the cover or the
door does not have any safety limit switch. Therefore, you can open it at any time. However, if there is
a hazard inside, the cover or the door that protects there has a safety limit switch.
- Those covers which have a safety limit switch have a name plate sticker shown below near the handle.
Most of the cases when carrying out paper feeding or maintenance work, you are going to open a cover with
a safety limit switch. Because it is dangerous due to existence of a drive system and it is difficult for you from
the operation panel to see such covers with a safety limit switch or the locations with a drive system (such
as the cover for the feeding shaft) on the front side or the rear side of the machine, the power supply is au-
tomatically shut down if one of such covers is opened.
Category Description
Instruction The location where the earth wire has been grounded
Prohibition If you carelessly touch the installation bracket of the loop de-
tection sensor, the sensor may not detect the loop properly.
Do not touch the part except at maintenance.

Warnings and Precautions for Roll Winder RW-101/Roll Winder RW-201
2
2-10 Accurio Label 190/bizhub PRESS C71cf
2.2
2.2.5 Guidelines for Safety Usage (General)
If the machine is used in a wrong way, the machine may be damaged or broken, or it may lead to a physical
danger to the operator. For the operator's safety, always follow the instructions described below.
-Read thoroughly the instructions about safety and warnings.
-Check that no one is around in dangerous areas before operating the machine.
-Never remove or disable safety covers or safety limit switches.
-Do not clean, maintain, or repair the machine while the machine is operating.
Always stop the machine and turn off the main power supply before each of the operations.
-Do not insert your hands in the machine while the machine is operating. (ex: removing samples)
-Always turn off the main power supply before opening the electric control panel.
-The edge of a paper is dangerous not only while the machine is operating but also while the machine
has stopped. Do not enter the space between the units carelessly.
-Never touch the rolling roller.
-If you notice any abnormal sound, vibration, or abnormal odor, immediately stop the machine.
2.2.6 Guidelines for Safety Usage (Paper Feeding/Winding)
When feeding or replacing a paper roll, always follow the instructions described below.
-Always stop the machine before feeding or replacing a paper roll with a new one.
-Stop the machine before installing or removing paper holding bars.
-Always stop the machine before moving or adjusting each part.
-When you open or close a cover, be careful not to get your hand or arm caught in or not to collide with
it. Special attention should be paid to the location with a caution label attached in order to avoid unex-
pected injury.
-Be careful not to touch projections such as those of safety limit switches. Failure to do so may cause
unexpected injury or malfunction.
2.2.7 Guidelines for Safety Usage (Safety and Maintenance)
For safety and maintenance of the machine, always follow the instructions described below.
-Do not operate a damaged machine or a machine that does not operate properly.
-Always inspect the machine before operating the machine and perform periodic inspections.
-Make sure that the power has been shut off before maintenance or repair works.
-For the inspections that require disassembly and assembly, always contact our customer engineer or
your service representative.
-Never reconstruct the machine or accessories. (ex: removing safety limit switches)
-When you desire any reconstruction of the machine, contact us or your service representative. We do
not take any responsibility for the reconstructions we have no concern with.
-Never peel off each label. If any label has been peeled off, ask us or your service representative for a
new label. Certainly attach the new label at the original position.
-When you open or close a cover, be careful not to get your hand or arm caught in or not to collide with it.
Special attention should be paid to the location with a caution label attached in order to avoid unex-
pected injury.
-Be careful not to touch projections such as those of safety limit switches.
Failure to do so may cause unexpected injury or malfunction.
2.2.8 Inspections before Power-on
Always check the following points before turning on the power of the machine.
1 Check that all the doors and caps or covers of the control panel, operation box, and relay box of the
machine are closed. (Rating plates indicating the caution have been attached on them.)
A high voltage may be applied to some components and parts, such as power supplies and terminals,
in those panels or boxes. If you touch these parts, you may get an electrical shock. Especially, check
that the door of the control panel has been closed.
2 Check that the main breaker is [OFF].
3 Check that connectors have been plugged and inserted in the appropriate positions as well as that any
wiring breakage is not present.

Accurio Label 190/bizhub PRESS C71cf 2-11
2.3 Regulation Notices for Main Body 2
2.3 Regulation Notices for Main Body
2.3.1 Laser Safety
This product employs a Class 3B laser diode having maximum power of 15 mW and wavelength of 787-800
nm.
This product is certified as a Class 1 laser product. Since the laser beam is concealed by protective housings,
the product does not emit hazardous laser radiation as long as the product is operated according to the in-
structions in this manual.

Regulation Notices for Main Body
2
2-12 Accurio Label 190/bizhub PRESS C71cf
2.3
2.3.2 Ozone Release
During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone
adversely. However, be sure the room where the machine is being used has adequate ventilation, especially
if you are printing a high volume of materials, or if the machine is being used continuously over a long period.
2.3.3 Electromagnetic Interference and Safety Approvals
This product must be used with a shielded network cable and shielded USB interface cable.
The use of non-shield cables is likely to result in interference with radio communications.
WARNING:
This is a Class A product. This product must not be used in residential areas. In a residential environment this
product may cause radio interference in which case the user may be required to take adequate measures.
For European Users
This product complies with the following EU directives:
Main Body: 2004/108/EC, 2006/95/EC and 2011/65/EU
Roll Winder RW-101/Roll Winder RW-201: 2006/42/EC and 2011/65/EU
This declaration is valid for the areas of the European Union (EU).
Declaration of Conformity is available at "http://www.konicaminolta.eu/".
This product complies with IEC61000-3-12.
This product is GS-certified for the Konica Minolta branded model C71cf and AccurioLabel 190.
For German Users
Der Höchste Schalldruckpegel beträegt 85 dB(A) oder weniger nach ISO 7779.
This device is not intended for use in the direct field of view at visual display workplaces.
To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct
field of view.
For U.S.A and Canada Users
This product is cTUVus-certified for the Konica Minolta branded model C71cf and AccurioLabel 190.
Notification for California Customers
This product uses a CR Lithium Battery which contains perchlorate material.
This perchlorate warning applies to perchlorate-containing lithium batteries sold or distributed in California,
USA.
“Perchlorate Material - Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (For U.S.A. Users)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful in-
terference in which case the user will be required to correct the interference at his own expense.
WARNING:
The design and production of this unit conform to FCC regulations, and any changes or modifications must
be registered with the FCC and are subject to FCC control. Any changes made by the purchaser or user with-
out first contacting the manufacturer will be subject to penalty under FCC regulations.
This device must be used with a shielded network cable and a shielded USB cable. The use of non-shielded
cables is likely to result in interference with radio communications and is prohibited under FCC rules.

Accurio Label 190/bizhub PRESS C71cf 2-13
2.3 Regulation Notices for Main Body 2
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 5) (For Canada Users)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
For EU member states only
This symbol means: Do not dispose of this product together with your household
waste!
Please refer to the information of your local community or contact our service
representatives regrading the proper handling of end-of-life electric and electron-
ic equipments. Recycling of this product will help to conserve natural resources
and prevent potential negative consequences for the environment and human
health caused by inappropriate waste handling.
Graphic symbols used on this machine
These are some of major exemplary graphical symbols.
2.3.4 Volatile Organic Compounds (VOC)
7 WARNING
-Tack paper contains an adhesive or pressure-sensitive adhesive that may contain toxic substances.
Volatile organic compounds (VOC) from the tack paper may lead to negative health effects in poorly
ventilated environment. Keep the room well ventilated.
Graphic
symbols
Descriptions Graphic
symbols
Descriptions Graphic
symbols
Descriptions
“ON” position “OFF” position STAND-BY
push-push
type switches
Ground/Earth
(Protective
bonding
terminal)
Ground/Earth
(Protective
earthing)
CLASS II
EQUIPMENT
Class II
equipment
with functional
earthing
Functional
earthing
General
precaution
High
temperature
Electrical
shock hazard
CAUTION
moving fan
blade
CAUTION
DOUBLE
POLE /
NEUTRAL
FUSING