Kontron CRTtoLCD-7 User manual

aFLAT-series
Flat Panel Controller
CRTtoLCD-7

CRTtoLCD7 User´s Guide
Contents
Contents
GENERAL INFORMATION AND IMPORTANT NOTES......................................................................... 2
1.1 User Information.......................................................................................2
1.2 Trademarks ..............................................................................................2
1.3 General ...................................................................................................2
1.4 Warranty..................................................................................................2
2. INTRODUCTION.............................................................................................................. 3
TECHNICAL INFORMATION SUMMARY........................................................................................ 3
3. CONFIGURATION............................................................................................................
3.1 Panel Vcc configuration JP 000 ....................................................................5
3.2 Backlight adjust configuration JP 001 ...........................................................5
3.3 Backlight Mode configuration JP 002 ............................................................5
3.4 Backlight ON/OFF configuration JP 003 .........................................................6
4. CONNECTORS ................................................................................................................ 6
4.1 DC Power Supply 4-pol. CN200......................................................................6
4.2 DC Power Supply DC-Jack CN201 or CN201-1 ....................................................6
4.3 VGA/RGB analog Input CN300.......................................................................
4.4 YUV analog input CN4001/CN4002.................................................................
4.5 DVI input connector CN6 .............................................................................8
4.6 SVHS Video Input CN12 ...............................................................................8
4. Composite video input CN13.........................................................................9
4.8 IR input CN1001........................................................................................9
4.9 OSD keypad connector CN102.......................................................................9
4.10 OSD keypad connector CN1003 ................................................................... 10
4.11 Serial OSD connector CN1002 ..................................................................... 10
4.12 JILI40-Interface CN800............................................................................. 11
4.13 JILI30-Interface CN 000........................................................................... 12
4.14 FLEX32 CN 003 ....................................................................................... 13
4.15 Backlight Connector CN 001...................................................................... 13
4.16 Backlight Connector CN 002...................................................................... 14
4.1 GPIO Connector CN 8000 ........................................................................... 14
4.18 Extension Connector CN8001 ..................................................................... 14
4.19 ADC Input Connector CN1000 (Light Sensor Input).......................................... 15
. ON SCREEN DISPLAY......................................................................................................1
5.1 Main Menue............................................................................................ 15
5.2 Input Select ........................................................................................... 16
5.2.1 Input Select - Main Picture Channel ............................................................. 16
5.2.2 Input Select - Scan Inputs ......................................................................... 16
5.2.3 Input Select - PIP Mode............................................................................. 1
5.2.4 Input Select - PIP Channel ......................................................................... 1
5.2.5 Input Select - PIP Size .............................................................................. 1
5.2.6 Input Select - PIP hor. Position................................................................... 18

CRTtoLCD7 User´s Guide
Contents
5.2. Input Select - PIP ver. Position ................................................................... 18
5.2.8 Input Select - Swap Main & PIP ................................................................... 18
5.3 Image Adjustments.................................................................................. 19
5.3.1 Image Adjustments - Auto Adjust ................................................................ 19
5.3.2 Image Adjustments - Clock......................................................................... 19
5.3.3 Image Adjustments - Phase........................................................................ 20
5.3.4 Image Adjustments - Bandwith................................................................... 20
5.3.5 Image Adjustments - Hor. Position .............................................................. 20
5.3.6 Image Adjustments - Ver. Position............................................................... 21
5.4 Color Adjustment..................................................................................... 21
5.4.1 Color Adjustment – Brightness ................................................................... 21
5.4.2 Color Adjustment – Contrast....................................................................... 22
5.4.3 Color Adjustment – Saturation.................................................................... 22
5.4.4 Color Adjustment – Hue ............................................................................ 22
5.4.5 Color Adjustment – Fleshtone..................................................................... 23
5.4.6 Color Adjustment – Backlight ..................................................................... 23
5.4. Color Adjustment - Auto Color Adjust ........................................................... 23
5.5 Advanced Color Adjustment ....................................................................... 24
5.5.1 Color Adjustment – Advanced – Gamma ........................................................ 24
5.5.2 Color Adjustment – Advanced –Color Space ................................................... 24
5.5.3 Color Adjustment – Advanced – Color Temp. .................................................. 25
5.5.4 Color Adjustment – Advanced – Red ............................................................. 25
5.5.5 Color Adjustment – Advanced – Green .......................................................... 25
5.5.6 Color Adjustment – Advanced – Blue............................................................ 26
5.6 Video Settings ........................................................................................ 26
5.6.1 Video Settings – Motion Processing ............................................................. 26
5.6.2 Video Settings – Sharpness........................................................................ 2
5.6.3 Video Settings – Film Mode ........................................................................ 2
5.6.4 Video Settings – Noise Reduction ................................................................ 2
5.6.5 Video Settings – Mpeg Processing ............................................................... 28
5. Video Settings – Decoder Settings ............................................................... 28
5. .1 Decoder Settings – Video Brightness............................................................ 28
5. .2 Decoder Settings – Video Contrast............................................................... 29
5. .3 Decoder Settings – Video Saturation............................................................ 29
5. .4 Decoder Settings – Video Hue..................................................................... 29
5. .5 Decoder Settings – Video Sharpness ............................................................ 30
5.8 Video Settings – CRTtoLCD multimedia........................................................ 30
5.8.1 Video Settings – Motion Processing (CRTtoLCD multimedia)............................. 30
5.8.2 Video Settings – Film Mode (CRTtoLCD multimedia) ....................................... 30
5.8.3 Video Settings – Enhancer (CRTtoLCD multimedia) ........................................ 31
5.8.4 Video Settings – Sharpness (CRTtoLCD multimedia) ....................................... 31
5.8.5 Video Settings – Cross Color (CRTtoLCD multimedia) ...................................... 31
5.8.6 Video Settings – Noise Reduction (CRTtoLCD multimedia) ............................... 32
5.8. Video Settings – Decoder Settings (CRTtoLCD multimedia) .............................. 32
5.8.8 Video Settings – Ext. Deinterlacer (CRTtoLCD multimedia)............................... 32
5.9 Scaling Adjustment .................................................................................. 33
5.9.1 Scaling Adjustment – Scaling Mode ............................................................. 33
5.9.2 Scaling Adjustment – Picture Flip ................................................................ 33
5.9.3 Scaling Adjustment – Zoom........................................................................ 34
5.9.4 Scaling Adjustment – Hor. Pan ................................................................... 34

CRTtoLCD7 User´s Guide
Contents
5.9.5 Scaling Adjustment – Ver. Pan .................................................................... 34
5.10 System Settings ...................................................................................... 35
5.10.1 System Settings – OSD Timeout................................................................... 35
5.10.2 System Settings – OSD Hor. Pos. ................................................................. 35
5.10.3 System Settings – OSD Ver. Pos................................................................... 35
5.10.4 System Settings – OSD Blend...................................................................... 36
5.10.5 System Settings – OSD Orientation .............................................................. 36
5.10.6 System Settings – OSD Language................................................................. 36
5.10. System Settings – Reset to Default .............................................................. 3
5.11 Audio Settings ........................................................................................ 3
5.11.1 Volume.................................................................................................. 3
5.11.2 Balance ................................................................................................. 3
5.11.3 Surround ............................................................................................... 38
5.11.4 Loudness ............................................................................................... 38
5.11.5 Pseudo Stereo......................................................................................... 38
5.11.6 Mode .................................................................................................... 39
5.11. Equalizer ............................................................................................... 39
5.12 TV ........................................................................................................ 40
5.12.1 TV - Program........................................................................................... 40
5.12.2 TV - Channel ........................................................................................... 40
5.12.3 TV - Frequency ........................................................................................ 41
5.12.4 TV - System............................................................................................. 41
5.12.5 TV - Scan Channel .................................................................................... 41
5.12.6 TV – Favorites ......................................................................................... 42
5.12. TV – Favorite Edit Menu ............................................................................. 42
5.12.8 TV - Auto install....................................................................................... 42
5.13 Radio.................................................................................................... 43
5.13.1 Radio - Station........................................................................................ 43
5.13.2 Radio - Frequency.................................................................................... 43
5.13.3 Radio - Scan Station................................................................................. 44
5.13.4 Radio - Save Station ................................................................................. 44
6. SERIAL OSD.................................................................................................................4
6.1 Settings ................................................................................................ 45
6.2 Input Select ........................................................................................... 45
6.3 Picture in Picture..................................................................................... 46
6.4 VGA Adjustment ...................................................................................... 46
6.5 Color Adjustment..................................................................................... 4
6.6 Advanced Color ....................................................................................... 4
6. Video .................................................................................................... 48
6.8 Scaling.................................................................................................. 48
6.9 Audio * ................................................................................................. 49
6.10 Equalizer *............................................................................................. 49
6.11 TV * ...................................................................................................... 50
6.12 OSD Settings .......................................................................................... 50
7. TECHNICAL SPECIFICATIONS............................................................................................ 1
8. SUPPORTED VIDEO MODES .............................................................................................. 3
9. LAYOUT / SCHEMATICS ................................................................................................... 4

CRTtoLCD7 User´s Guide
Contents
10. TECHNICAL SUPPORT .....................................................................................................
11. REVISION HISTORY........................................................................................................ 6

TVtoLCD User´s Guide
General information and important notes
2
General information and important notes
1.1 User Information
Copyright 200 by Kontron Embedded Modules GmbH.
In this document Kontron Embedded Modules GmbH will also be referred to by the short form “Kontron
Embedded Modules”.
The information in this document has been carefully checked and is believed to be accurate and reliable.
However, no responsibility is assumed for inaccuracies. Furthermore, Kontron Embedded Modules
reserves the right to make changes to any portion of this manual to improve reliability, function or
design. Kontron Embedded Modules does not assume any liability for any product or circuit described
herein.
1.2 Trademarks
AT and IBM are trademarks of International Business Machines.
XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
All other products and trademarks mentioned in this manual are trademarks of their respective owners.
The reproduction, transmission or use of this document or its contents is not permitted without
expressed written authority.
Offenders will be liable for damages. All rights created by patent grant or registration of a utility model
or design, are reserved.
1.3 General
For the circuits, descriptions and tables indicated no responsibility is assumed as far as patents or other
rights of third parties are concerned.
The information in the Technical Descriptions describes the type of the boards and shall not be
considered as assured characteristics.
The reproduction, transmission or use of this document or its contents is not permitted without express
written authority. Offenders will be liable for damages. All rights, including rights created by patent
grant or registration of a utility model or design, are reserved.

TVtoLCD User´s Guide
General information and important notes
2
1.4 Warranty
Each board is carefully and thoroughly tested before being shipped. If, however, problems should occur
during the operation, please check your user specific settings of all boards included in your system. This
is often the source of the fault. If a board is defective, it can be sent to your supplier for repair. Please
take care of the following steps:
- The board returned should correspond to the factory default settings since a test is only
possible under these settings.
- In order to repair your board as fast as possible, we require some additional information from
you. Please fill out the attached Repair Form and include it with the defective board.
- If possible, the board will be upgraded to the latest version without additional cost.
- Upon receipt of the board, please be aware that your user specific settings are changed during
the test.
Within the guarantee, the repair is free as long as the guarantee conditions were kept. If no fault has
been found, you will be charged with the test cost due to the high test expenditure. Repairs outside of
the guarantee will be charged.
This Kontron Embedded Modules product is warranted against defects in material and workmanship for
our guaranteed warranty period from the date of shipment. During the warranty period, Kontron
Embedded Modules will, at its option, either repair or replace products which prove to be defective.
For warranty service or repair, the product must be returned to a service facility designated by Kontron
Embedded Modules.
The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance or
handling by buyer, unauthorized modification or misuse, operation outside of the environmental
specifications for the product, or improper installation or maintenance.
Kontron Embedded Modules will not be responsible for any defects or damages due to a faulty Kontron
Embedded Modules product other than the products supplied by Kontron Embedded Modules.

TVtoLCD User´s Guide
Introduction
3
2. Introduction
The CRTtoLCD- is a highly integrated TFT panel interface controller, which allows an easy adaptation of
standard video input sources like S-video, composite video, DVI or analog RGB to a digital TFT panel. The
CRTtoLCD- only needs one single 12V power supply and incorporates all needed functionality to build
up a full featured TFT monitor. The card generates the necessary power sequencing for the flat screen.
The highly flexible architecture of the CRTtoLCD- panel interface allows adapting nearly any available
TFT panel. Therefore a variety of panel adapters and programming are available on request.
Technical Information Summary
Features
- Zoom and shrink scaling (all resolutions from VGA to WUXGA)
- Frame rate conversion
- Integrated 8-bit triple-channel ADC / PLL
- Integrated Ultra-Reliable DVI
TM
receiver
- Optional Integrated High-bandwidth Digital Content Protection (HDCP)
- On-chip versatile OSD engine
- All system clocks synthesized from a single external crystal
- Programmable gamma correction (CLUT)
- RealColor
TM
technology provides flesh tone adjustment
- Optional TV-Tuner-Extension board
Analog RGB Input Port
- Supports up to 165MHz (up to UXGA 60Hz and WUXGA 60Hz reduced blanking)
- Support for Sync-on-Green (SOG)
- Can be used as a YUV Input
Ultra-Reliable DVI
TM
Receiver
- Single link on-chip TMDS Rx up to 160 MHz operation
- Direct connect to all DVI compliant TMDS transmitters
- Optional High-bandwidth Digital Content Protection (HDCP)
NTSC,PAL or SECAM input
- VIDEO DECODER WITH S-VIDEO AND COMPOSITE VIDEO INPUT CAPABILITIES
Output Format
- Support for 8 or 6-bit panels (with high quality dithering)
- One or two pixel output format
- Double Channel LVDS or 18bit TTL Output
Auto-Configuration / Auto-Detection
- Phase and image positioning
- Input format detection
- Compatibility with all graphic cards and standard VESA modes
Frame Store Interface
- 16 MB DDR-SDRAM Frame buffer
On-chip OSD Controller
- Bit-mapped OSD capability - 12 24-bit colors tiles
- Horizontal and vertical stretch of OSD images

TVtoLCD User´s Guide
Technical Information Summar
4
RealColor
TM
Technology
- Color filtering in YUV domain
- Digital brightness, contrast, hue and saturation control for analog, digital and video inputs
- Proprietary flesh tone adjustment
Operating Modes
- Frame rate conversion and scaling of images
- Bypass mode with no filtering and/or frame buffering
- 1:1 centering
- De-interlaced zoom
- Frame Sync and Free Run display synchronization modes
High-Quality Advanced Scaling
- Fully programmable zoom/shrink ratios
- Independent horizontal / vertical zoom and shrink
- Variable sharpness control
- Moire cancellation
- Adjustable scaling algorithms
Genesis FLI2310 Digital Video Format Converter
- High quality conversion of digital video formats
- Adaptive Motion Deinterlacing powered by Faroudja
- Motion Adaptive Noise Reduction
- DCDi
TM
two dimensional vector interpolation to improve quality of interlaced video formats
Display Interface Features :
- Control signal generation for backlight inverter
- backlight dimming support (PWM and voltage controlled )
- Voltage generation and power sequence control for panel
- Flat screens can be used with either 3.3V, 5V or 12V.
- JILI30/40 (LVDS) and FLEX32 (digital) panel interface (one and double port up to 24 Bit)
Operating Features:
- 5 button user interface (OSD Keypad)
- On Screen Display (OSD) control for all features
- Full multi sync capable
- VESA DPMS and DDC2B support
- Single voltage supply (+12V DC )
- Dynamic Power Management for minimal power consumption via DPMS
- No software drivers needed!

TVtoLCD User´s Guide
Configuration
5
3. Configuration
3.1 Panel Vcc configuration JP7000
Use JP 00 to control Panel Vcc
Connector Double Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3 Pin
1-2 2-3 open
JP7000
O O O 5V 12V 3,3V
Never
unplug/r
eplug this
while in
use!
default
3.2 Backlight adjust configuration JP7001
Use JP 001 to control Backlight adjust Voltage
Connector Double Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3 Pin
1-2 2-3 Delivery
Default
JP7001
O O O 5V 12V 1-2 closed
Never
unplug/replug
this while in
use!
5V
3.3 Backlight Mode configuration JP7002
Use JP 002 to control Backlight Mode PWM/Linear
Connector Double Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3 Pin
1-2 2-3 Delivery Default
JP7002
O O O Linear PWM 1-2 closed
Never
unplug/replug
this while in
use!
Linear

TVtoLCD User´s Guide
Connectors
6
3.4 Backlight ON/OFF configuration JP7003
Use JP 003 to control polarity of backlight ON/OFF
Connector Double Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3 Pin
2-3 1-2 Delivery
Default
JP7003
O O O
/ON ON 1-2 closed
Never
unplug/replug
this while in
use!
ON
4. Connectors
4.1 DC Power Supply 4-Pol. CN200
Apply operating voltage using connector CN200
4 Contact Connector, Single Row, Right Angle, Polarization, Through hole
Pin Name Description
O 1 NC Not connected
O 2 GND Power Groundl
O 3 GND
Power Ground
O
4 +12V 12V DC Power
4.2 DC Power Supply DC-Jack CN201 or CN201-1
Apply operating voltage using connector CN201/CN201-1
DC POWER JACK, Case/Size : PCB-Mount 2mm Pin Diameter
Pin Name Description
O 1 +12V +12 V DC
O
2 GND
Power Ground

TVtoLCD User´s Guide
Connectors
7
4.3 VGA/RGB analog Input CN300
High Density Sub-D-Connector 15 Contacts, Receptacle
Case/Size : Right Angle, Through Hole
Pin Name Description
O 1 RED Analog input red
O 2 GREEN Analog Input Green
O
3 BLUE Analog Input Blue
O
4 ID2 Not Connected
O
GND Analog Ground
O
6 GND Analog Ground Red
O
7 GND Analog Ground Green
O
8 GND Analog Ground Blue
O
9 DDC_5V +5V Power Supply from Video Card
O
10 GND Analog Ground
O
11 ID0 Not Connected
O
12 DDC_SDA DDC Serial Data
O
13 HSYNC Horizontal Sync input
O
14 VSYNC Vertical Sync input
O
1 DDC_SCL DDC Serial Clock
4.4 YUV analog input CN4001/CN4002
3x Chinch Red , Green, Blue
Case/Size : Right Angle, Through Hole
Pin Name Description
O 1 BLUE
Analog input Pb
O 2 RED
Analog input Pr
O
3 GND
Analog GroundPB/ Pr
O
O
4
GREEN
GND
Analog input Y
Analog Ground Y

TVtoLCD User´s Guide
Connectors
8
4. DVI input connector CN6
This input supports the connection of DVI capable video cards and supports resolutions from 640x480 up
to 1920x1200.
Connector Double Row 2,54 mm, 10 Contacts, Gold plated
Case/Size : Vertical, Through Hole
Description Name
Pin
Pin
Name
Description
Receiver Signal(-) ( RX2- ) RX2- 1
O O
2
RX2+ Receiver Signal(+) ( RX2+ )
Power Ground GND 3
O O
4
NC Not connected
Not connected NC
O O
6
SCL_IN
I
2
C clock
I
2
C Data SDA_IN 7
O O
8
NC Not connected
Receiver Signal(-) ( RX1- ) RX1- 9
O O
10
RX1+ Receiver Signal(+) ( RX1+ )
Power Ground GND 11
O O
12
NC Not connected
Not connected NC 13
O O
14
+5V +5V DC from DVI video card
Power Ground GND 1
O O
16
HP Hot Plug
Receiver Signal(-) ( RX0- ) RX0- 17
O O
18
RX0+ Receiver Signal(+) ( RX0+ )
Power Ground GND 19
O O
20
NC Not connected
Not connected NC 21
O O
22
GND Power Ground
Clock Signal(+) (RXC+) RXC+ 23
O O
24
RXC- Clock Signal(-) (RXC-)
Not connected NC C1
O O
C2
NC Not connected
Not connected NC C3
O O
C4
NC Not connected
Power Ground GND C
O O
C _1
GND Power Ground
4.6 SVHS Video Input CN12
This input converts NTSC, PAL or SECAM in S-video to digitized component video
Pin Name Description
O 1 GND Power Ground
O 2 GND Power Ground
O
3 Y
Y component of video signal
O
4 C
C component of video signal

TVtoLCD User´s Guide
Connectors
9
4.7 Composite video input CN13
This input converts NTSC, PAL or SECAM in composite video to digitized component video.
Chinch Connector, Right Angle, Yellow
Pin Name Description
O 1 GND Power Ground
CN13
O
2 CVBS
CVBS Video Signal
4.8 IR input CN1001
This input connects a IR Receiver with the board
3 Contact Connector, Single Row, Straight, through hole
Pin Name Description
O 1 VCC 5 Volts output
O 2 GND Power Ground
CN1001
O
2 Out
Output from the IR receiver
4.9 OSD keypad connector CN102
14 Contacts boxed IDC Connector, double row,
Straight, through hole
Description Name
Pin
Pin
Name
Description
+5V DC Power VCC 1
O O
2
LED LED Enable (Operating)
Confirm Key (TTL) KEY 3
O O
4
KEY OSD Menu key (TTL)
Down Key (TTL) KEY
O O
6
KEY Up Key (TTL)
ADC Input *Note1 ADC_IN 7
O O
8
IR Output of IR receiver
Switch LED (TTL) KEY 9
O O
10
KEY ON/OFF Key (TTL)
Low active Reset (TTL) /Reset 11
O O
12
+12V +12V DC Power
Power Ground GND 13
O O
14
GND +5V DC from DVI video card
*Note1: Input range is 0 - 3V

TVtoLCD User´s Guide
Connectors
10
4.10 OSD keypad connector CN1003
Connector: Molex 53261-1471
Matching Connector: Molex 51021-1400
Connector Single Row, 14 contacts, Case/Size : Right Angle, 1,25mm Pitch
Pin Name Description
O 1 LED2 LED Red (3.3V output)
O 2 LED1 LED Green (3.3V output)
O
3 GND Key Power Ground
O
4 KEY Key Button (POWER)
O
GND Key Power Ground
O
6 KEY Key Button (Menu)
O
7 KEY Key Button (Right)
O
8 NC Not Connected
O
9 NC Not Connected
O
10 KEY Key Button (Left)
O
11 KEY Key Button (Exit)
O
12 KEY Key Button (AUTOADJUST)
O
13 GND Power Ground
O
14 VDD +3.3V Keypad Power Out
O
4.11 Serial OSD connector CN1002
The OSD ( On Screen Display ) can be controlled either trough the keypad or the serial connector CN1002
for configuration purposes or mass production. See also chapter 1.5 and chapter 1.9 for detailed
description.
Caution! The transmit and receive signals have RS232C level
and are crossed!
10 Contacts boxed IDC Connector, double row,
straight, through hole
Description Name
Pin
Pin
Name
Description
Not Connected NC 1
O O
2
NC Not Connected
Transmit Signal COM_TXD
3
O O
4
NC Not Connected
Receive Signal COM_RXD
O O
6
NC Not Connected
Not Connected NC 7
O O
8
NC Not Connected
Power Ground GND 9
O O
10
+5VY +5V DC Power

TVtoLCD User´s Guide
Connectors
11
4.12 JILI40-Interface CN800
All flat screen signals are LVDS compatible
Connector Double Row 2mm, 40 Contacts, Gold plated
Case/Size : Straight, Through Hole
Description Name
Pin
Pin
Name
Description
Enables Backlight BLON#
1 O O 2
BLON# Enables Backlight
Backlight Adjust BLADJ
3 O O 4
STX3+ Even Receiver Signal(+) (R2IN 3+)
Even Receiver Signal(-) (R2IN 3-) STX3-
O O 6
+12V +12V
Even Clock Signal(+) (CK2IN +) STXC+
7 O O 8
STXC- Even Clock Signal(-) (CK2IN -)
+12V +12V
9 O O 10
STX2+ Even Receiver Signal(+) (R2IN 2+)
Even Receiver Signal(-) (R2IN 2-) STX2-
11 O O 12
+12V +12V
Even Receiver Signal(+)(R2IN1+) STX1+
13 O O 14
STX1- Even Receiver Signal(-) (R2IN 1-)
+12V +12V
1 O O 16
STX0+ Even Receiver Signal(+) (R2IN 0+)
Even Receiver Signal(-) (R2IN 0-) STX0-
17 O O 18
+12V +12V
Odd Receiver Signal(+)(R1IN 3+) FTX3+
19 O O 20
FTX3- Odd Receiver Signal(-) (R1IN 3-)
Power Ground GND
21 O O 22
GND Power Ground
I
2
C clock DDCSCL
23 O O 24
DDCSDA I
2
C Data
Power Ground GND
2 O O 26
FTXC+ Odd Clock Signal(+) (CK1IN +)
Odd Clock Signal(-) (CK1IN -) FTXC-
27 O O 28
GND Power Ground
Odd Receiver Signal(+)(R1IN 2+) FTX2+
29 O O 30
FTX2- Odd Receiver Signal(-) (R1IN 2-)
Power Ground GND
31 O O 32
FTX1+ Odd Receiver Signal(+) (R1IN 1+)
Odd Receiver Signal(-) (R1IN 1-) FTX1-
33 O O 34
GND Power Ground
Odd Receiver Signal(+)(R1IN 0+) FTX0+
3 O O 36
FTX0- Odd Receiver Signal(-) (R1IN 0-)
Power Ground GND
37 O O 38
GND Power Ground
Panel VCC ( switched ) Vcc_P
39 O O 40
Vcc_P Panel VCC ( switched )

TVtoLCD User´s Guide
Connectors
12
4.13 JILI30-Interface CN7000
All JILI (JUMPtec Intelligent LVDS Interface ) signals are LVDS
compatible.
Fine Wire, 30 Contacts, single row, Right Angle, Series : JAE-FI-
X30H
Description Name
Pin
Pin
Name
Description
Odd Receiver Signal(-) (R1IN 0-) FTX0- 1 O O 2
FTX0+ Odd Receiver Signal(+) (R1IN 0+)
Odd Receiver Signal(-) (R1IN 1-) FTX1- 3 O O 4
FTX1+ Odd Receiver Signal(+) (R1IN 1+)
Odd Receiver Signal(-) (R1IN 2-) FTX2- O O 6
FTX2+ Odd Receiver Signal(+) (R1IN 2+)
Power Ground GND 7 O O 8
FTXC- Odd Clock Signal(-) (CK1IN -)
Odd Clock Signal(+) (CK1IN +) FTXC+ 9 O O 10
FTX3- Odd Receiver Signal(-) (R1IN 3-)
Odd Receiver Signal(+)(R1IN 3+) FTX3+ 11 O O 12
STX0- Even Receiver Signal(-) (R2IN 0-)
Even Receiver Signal(+)(R2IN 0+) STX0+ 13 O O 14
GND Power Ground
Even Receiver Signal(-)(R2IN 1-) STX1- 1 O O 16
STX1+ Even Receiver Signal(+) (R2IN 1+)
Power Ground GND 17 O O 18
STX2- Even Receiver Signal(-) (R2IN 2-)
Even Receiver Signal(+)(R2IN 2+) STX2+ 19 O O 20
STXC- Even Clock Signal(-) (CK2IN -)
Even Clock Signal(+) (CK2IN +) STXC+ 21 O O 22
STX3- Even Receiver Signal(-) (R2IN 3-)
Even Receiver Signal(+)(R2IN 3+) STX3+ 23 O O 24
GND Power Ground
I²C Data DDCSDA 2 O O 26
DEN Display Enable
I²C Clock DDCSCL 27 O O 28
Vcc_P Panel VCC ( switched )
Panel VCC ( switched ) Vcc_P 29 O O 30
Vcc_P Panel VCC ( switched )

TVtoLCD User´s Guide
Connectors
13
4.14 FLEX32 CN7003
This connector directly matches through an interface cable for 31/41 pin VGA/SVGA
TFT interface. All flat screen signals are LVTTL compatible (3.3V )
Flatfoil Connector 32 Contacts, Right Angle, Bottom Contact
Case/Size : 0,5mm Pitch, Series : 6210 / ZIF
Description Name Pin Pin Name Description
Power Ground GND 1 O O 2 SCLK Data clock
Latch pulse LP 3 O O 4 FLM First Line Marker
Power Ground GND 5 O O 6 P0 Panel Data R0
Panel Data R1 P1 7 O O 8 P2 Panel Data R2
Panel Data R3 P3 9 O O 10 P4 Panel Data R4
Panel Data R5 P5 11 O O 12 GND Power Ground
Panel Data G0 P6 13 O O 14 P7 Panel Data G1
Panel Data G2 P8 15 O O 16 P9 Panel Data G3
Panel Data G4 P10 17 O O 18 P11 Panel Data G5
Power Ground GND 19 O O 20 P12 Panel Data B0
Panel Data B1 P13 21 O O 22 P14 Panel Data B2
Panel Data B3 P15 23 O O 24 P16 Panel Data B4
Panel Data B5 P17 25 O O 26 GND Power Ground
Data Enable MOD ( DE ) 27 O O 28 PANEL_VCC Panel Power
Panel Power PANEL_VCC
29 O O 30 R/L Right/Left
Up/Down rotate U/D 31 O O 32 NC Not connected
4.1 Backlight Connector CN7001
Connector: Molex 53261-1071
Matching Connector: Molex 51021-1000
Connector Single Row, 10 Contacts, Case/Size : Right Angle, 1,25mm
Pitch
Pin
Name Description
O
1
BLON
BACKLIGHT CONTROL SIGNAL (TTL, REFER TO
JP7003)
O
2GND Power Ground
O
3GND Power Ground
O
4Backlight power supply
O
5Backlight power supply
O
6Backlight power supply
O
7Backlight power supply
TYPICAL. +12V (NOTE SAME AS DC INPUT
VOLTAGE , 1 AMPERE PER CONTACT ALLOWED)
O
8GND Power Ground
O
9GND Power Ground
O
10 BKLTADJ analog 0V to +5V or 0V to +12V (refer to
JP7001)

TVtoLCD User´s Guide
Connectors
14
4.16 Backlight Connector CN7002
Connector: Molex 53261-0790
Matching Connector: Molex 51021-0700
Connector Single Row, 7 Contacts, Case/Size : Right Angle, 1,25mm Pitch
Pin
Name
Description
O
1
NC
Not connected
O
2
BKLTADJ
analog 0V to +5V or 0V to +12V (refer
JP7001)
O
3
GND
Power Ground
O
4
Backlight power supply
O
5
Backlight power supply
Typ. +12V (Note same as DC Input Voltage ,
1Amp. Per Contact allowed)
O
6
GND
Power Ground
O
7
BLON
Backlight control signal (TTL, refer to JP7003)
Polarity settings
4.17 GPIO Connector CN 8000
Connector: Molex 53261-0590
Matching Connector: Molex 51021-0500
Pin Name Description
O
1 DVD3.3 3.3 Volt output source (max.50mA)
O
2 GND Ground
O
3 GPIO0 General Purpose I/O
O
4GPIO1 General Purpose I/O
O
5PWM3 PWM Outputsignal
4.18 Extension Connector CN8001
Connector Triple Row 2mm, 75 Contacts, Gold plated
Case/Size : Right Angle, Through Hole
For add-on cards (e.g. TVtoLCD)
Additional Information on Request

TVtoLCD User´s Guide
On Screen Displa
15
4.19 ADC Input Connector CN1000 (Light Sensor Input)
Connector: Molex 53261-0590
Matching Connector: Molex 51021-0500
Pin Name Description
O
1 GND Power Ground
O
2 ADC1 ADC1 Input *Note1
O
3 DVDD3.3
3.3 Volt output source (max.50mA)
O
4ADC2 ADC2 Input *Note1
O
5GND Power Ground
*Note1: Input range is 0 - 3V. Onboard pulled up to DVDD3.3 through 4, 7 KΩresistor.
. On Screen Display
With the OSD ( On Screen Display ) you can modify the settings and control the special features of the
CRTtoLCD- . The OSD uses a number of menus for making changes and turning the special features on or
off. The configuration can be done via the OSD-keypad (OSD-Panel-Kit).
To start the OSD press the “OSD” button on the keypad, after switching the power supply on. If a valid
flat panel configuration is installed, the OSD Main Menu will be displayed.
To select an menu point, simply use the button “UP” or ”DOWN” to move the cursor to the menu point
you want and press the button “OSD”. To get back to the previous menu point press the “CONFIRM”
button.
To select a function, simply use “OSD”-button to select the field.
Use “UP” or “DOWN” to select a value for that field. With the “CONFIRM” button you can exit the current
function.
.1 Main Menue
The OSD always starts with the “Main Menu”-screen.
figure 1: Main Menu