Kontron V Panel Express 121 User manual

V Panel Express
User’s Guide (Version 1.01)
0-0096-3678
If it’s embedded, it’s Kontron
StockCheck.com

This page is intentionally left blank.
www.kontron.com
StockCheck.com

1. Table of Contents V Panel Express –User’s Guide (V1.01)
1. Table of Contents
1. Table of Contents ..................................................................................................................................... 1
1.1. Table of Figures...................................................................................................................................... 2
2. Introduction ........................................................................................................................................... 4
2.1. Symbols used in this Guide ....................................................................................................................... 5
3. Important Instructions............................................................................................................................. 6
3.1. Note on the Warranty .............................................................................................................................. 6
3.2. Exclusion of Accident Liability Obligation.................................................................................................... 6
3.3. Liability Limitation / Exemption from the Warranty Obligation ........................................................................ 6
4. General Safety Instructions for IT Equipment............................................................................................... 7
4.1. Electrostatic Discharge (ESD) ................................................................................................................... 9
4.1.1. Grounding Methods.......................................................................................................................... 9
4.2. Instructions for the Lithium Battery........................................................................................................... 9
5. Electromagnetic Compatibility (Class A Device) ..........................................................................................10
5.1. Electromagnetic Compatibility (EU) ..........................................................................................................10
5.2. FCC Statement (USA)..............................................................................................................................10
5.3. EMC Compliance (Canada) .......................................................................................................................10
6. Scope of Delivery ....................................................................................................................................11
6.1.1. Optional Parts ................................................................................................................................11
6.2. Type Label and Product Identification .......................................................................................................11
7. Product Description ................................................................................................................................12
7.1. Front Side View .....................................................................................................................................14
7.1.1. USB Interface Connector on the Front Side ..........................................................................................14
7.1.2. Front Plate Versions ........................................................................................................................14
7.1.3. Display with Touch Screen ................................................................................................................15
7.2. Bottom Side (with Interfaces)..................................................................................................................16
7.2.1. DC-IN Power Connector ....................................................................................................................17
7.2.2. Power Button.................................................................................................................................17
7.2.3. Grounding Screw (M4) with lock Washers.............................................................................................17
7.2.4. LED Control Indicators .....................................................................................................................18
7.2.5. CompactFlash™ Slot (with optional installed CF Card) ............................................................................18
7.2.6. Interfaces .....................................................................................................................................19
7.2.7. Removable HDD Drive Tray (with optional installed HDD)........................................................................20
7.3. Left and Right Side View .........................................................................................................................21
7.4. Top Side ..............................................................................................................................................22
7.5. Rear Side .............................................................................................................................................23
7.6. Integrated ETXexpress®Module................................................................................................................24
7.6.1. Fuse .............................................................................................................................................24
7.7. PCI or PCIe Riser Cards............................................................................................................................24
8. Accessing Internal Components ................................................................................................................25
8.1. Installing/Removing the Expansion Cards ..................................................................................................25
8.2. Replacing the Removable HDD Tray ...........................................................................................................27
8.3. Replacing the Lithium Battery..................................................................................................................29
8.4. Replacing the Fuse ................................................................................................................................30
www.kontron.com 1
StockCheck.com

1. Table of Contents V Panel Express – User’s Guide (V1.01)
9. Installation Instructions......................................................................................................................... 31
10. Starting Up.......................................................................................................................................... 34
10.1. Connecting to Power............................................................................................................................ 34
10.1.1. DC Connection ............................................................................................................................. 34
10.1.2. Connecting to AC Power Source via the AC/DC Adapter ......................................................................... 35
10.2. Operating System and Hardware Component Drivers .................................................................................. 36
10.2.1. Hints for the Installation of the ELO Touch Screen Controller Driver........................................................ 36
11. Maintenance and Prevention.................................................................................................................. 39
11.1. Touch Screen Care and Cleaning............................................................................................................. 39
12. Main Specifications .............................................................................................................................. 40
12.1. Electrical Specifications ....................................................................................................................... 41
12.1.1. Electrical Specifications for the AC/DC Adapter................................................................................... 41
12.2. Mechanical Specifications..................................................................................................................... 41
12.3. Environmental Specifications ................................................................................................................ 42
12.4. CE Directives and Standards .................................................................................................................. 43
13. Technical Appendix - Interfaces.............................................................................................................. 44
13.1. Power Connector................................................................................................................................. 44
13.2. USB Port............................................................................................................................................ 44
13.3. Serial Port (COM1, COM2, COM3) RS232 ................................................................................................... 44
13.4. Serial Port (COM4) RS422 (Option) ......................................................................................................... 45
13.5. Serial Port (COM4) RS485 (Option) ......................................................................................................... 45
13.6. DVI-I Connector (Single Link)................................................................................................................ 46
14. Technical Support................................................................................................................................. 47
14.1. Returning Defective Merchandise ........................................................................................................... 47
1.1. Table of Figures
Fig. 1: Bottom view .....................................................................................................................................13
Fig. 2: Right view ........................................................................................................................................13
Fig. 3: Frontal view......................................................................................................................................13
Fig. 4: Left view ..........................................................................................................................................13
Fig. 5: Top view...........................................................................................................................................13
Fig. 6: Rear view .........................................................................................................................................13
Fig. 7: Frontal view of the V Panel Express system (shown with a 12.1" display); .....................................................14
Fig. 8: V Panel Express (interface side) ............................................................................................................16
Fig. 9: Detail of the DC Power connector shown without Phoenix terminal ..............................................................17
Fig. 10: Power button and LED indicators.........................................................................................................17
Fig. 11: Power LEDs and Error Codes ...............................................................................................................18
Fig. 12: Detail with drive tray for SATA HDD (shown with opened removable HDD drive tray) ......................................20
Fig. 13: V Panel Express (left side)..................................................................................................................21
Fig. 14: V Panel Express (right side)................................................................................................................21
2www.kontron.com
StockCheck.com

1. Table of Contents V Panel Express –User’s Guide (V1.01)
Fig. 15: Top side of V Panel Express ................................................................................................................ 22
Fig. 16: Rear side of V Panel Express ............................................................................................................... 23
Fig. 17: Fuse, label for fuse value and Lithium battery location............................................................................ 24
Fig. 18: Open the access door of the V Panel Express System ............................................................................... 26
Fig. 19: V Panel Express system – opened access door (systemis shown with PCI expansion slots) .............................. 26
Fig. 20: Detail: removable HDD tray of the system ............................................................................................. 27
Fig. 21: Rear side of the removed HDD tray ...................................................................................................... 27
Fig. 22: Left side of the HDD tray ................................................................................................................... 27
Fig. 23: Removed HDD tray ........................................................................................................................... 27
Fig. 24: Right side of the HDD tray ................................................................................................................. 27
Fig. 25: Removed HDD tray with installd HDD (SATA0) ....................................................................................... 27
Fig. 26: Removed HDD tray without HDD ......................................................................................................... 27
Fig. 27: Detail of the V Panel Express – OPERATOR ACCESS AREA ........................................................................... 29
Fig. 28: Detail top side: Systems delivering status with mounted clemps (shown as a detail of a15" display box) .......... 31
Fig. 29: Detai top sidel: Systems without mounting clamps (shown as a detail of a15" display box) ............................ 31
Fig. 30: Panel mounting for V Panel Express systems ......................................................................................... 32
Fig. 31: DC-connector (without Phoenix plug terminal)...................................................................................... 34
Fig. 32: DC-Phoenix plug terminal (AWG 18) .................................................................................................... 34
Fig. 33: External AC/DC adapter (Option) ........................................................................................................ 35
Fig. 34: Accept License Agreement................................................................................................................. 36
Fig. 35: Installing the touch files ................................................................................................................... 36
Fig. 36: Setup Complete for calibration........................................................................................................... 37
Fig. 37: ELO Touchscreen properties............................................................................................................... 37
www.kontron.com 3
StockCheck.com

2. Introduction V Panel Express – User’s Guide (V1.01)
2. Introduction
Kontron Europe GmbH would like to point out that the information contained in this manual may be subject to technical
alteration, particularly as a result of the constant upgrading of Kontron Europe products. The attached documentation
does not entail any guarantee on the part of Kontron Europe with respect to technical processes described in the manual
or any product characteristics set out in the manual. Kontron Europe does not accept any liability for any printing errors
or other inaccuracies in the manual unless it can be proven that Kontron Europe is aware of such errors or inaccuracies or
that Kontron Europe is unaware of these as a result of gross negligence and Kontron Europe has failed to eliminate these
errors or inaccuracies for this reason. Kontron Europe expressly informs the user that this manual only contains a general
description of technical processes and instructions which may not be applicable in every individual case. In cases of
doubt, please contact Kontron Europe.
This manual is protected by copyright. All rights are reserved by Kontron Europe. Copies of all or part of this manual or
translations into a different language may only be made with the prior written consent of Kontron Europe. Kontron
Europe points out that the information contained in this manual is constantly being updated in line with the technical
alterations and improvements made by Kontron Europe to the products and thus this manual only reflects the technical
status of the products by Kontron Europe at the time of printing.
© 2012 by Kontron Europe GmbH
Printing and duplication, even of sections, is only permissible with the express approval of
Kontron Europe GmbH
Office Eching
Oskar-von-Miller-Str. 1
85386 Eching near Munich
Germany
4www.kontron.com
StockCheck.com

2. Introduction V Panel Express –User’s Guide (V1.01)
2.1. Symbols used in this Guide
Symbol Meaning
This symbol indicates the danger of injury to the user or the risk of damage to the product if the
corresponding warning notices are not observed.
This symbol indicates that the product or parts thereof may be damaged if the corresponding warning
notices are not observed.
This symbol indicates general information about the product and the user manual.
This symbol indicates detail information about the specific product configuration.
This symbol precedes helpful hints and tips for daily use.
® Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of the Microsoft Corporation.
® IBM, PC-AT, OS/2 and PS/2 are registered trademarks of the International Business Machines Corporation.
® Intel and Pentium are registered trademarks of Intel Corporation.
® AMI is a registered trademark of American Megatrends, Inc.
Other product names cited in this manual may also be trademarks and are used here solely for identification purposes.
www.kontron.com 5
StockCheck.com

3. Important Instructions V Panel Express – User’s Guide (V1.01)
3. Important Instructions
This chapter contains safety instructions which must be observed when using the V Panel Express.
The manufacturer’s instructions provide useful information on your V Panel Express.
3.1. Note on the Warranty
Due to their limited service life, parts which by their nature are subject to a particularly high degree of wear (wearing
parts) are excluded from the warranty beyond that provided by law. This applies to batteries, to the display backlighting,
for example.
3.2. Exclusion of Accident Liability Obligation
Kontron Europe shall be exempted from the statutory accident liability obligation if the user fails to observe the safety
instructions.
3.3. Liability Limitation / Exemption from the Warranty Obligation
In the event of damage to the device caused by failure to observe the hints in this manual and eventually on the device
(especially the safety instructions included in the chapter “General Safety Instructions for IT Equipment”), Kontron
Europe shall not be required to honor the warranty even during the warranty period and shall be exempted from the
statutory accident liability obligation.
6www.kontron.com
StockCheck.com

4. General Safety Instructions for IT Equipment V Panel Express –User’s Guide (V1.01)
4. General Safety Instructions for IT Equipment
Please read this chapter carefully and observe the instructions for your own safety and correct use of the device.
The chapter also contains information on approval and interference suppression of your device.
The device has been built and tested by Kontron Europe in accordance to EN 60950-1 and left the company in a perfectly
safe condition.
In order to maintain this condition and ensure safe operation, the user must observe the instructions and warnings on
the device and in the manual.
❏The device must be used in accordance with the instructions for use.
❏The electrical installations in the room must correspond to the requirements of the respective regulations.
❏Take care that there are no cables, particularly power cables, in areas where persons can trip over them.
❏Do not use a power cable in sockets shared by a number of other power consumers. Do not use an extension cable.
❏The unit is only completely disconnected from the DC main power source, when the DC power cord is disconnected
either from the power source or the unit. Therefore, the DC power cord and its connectors must always remain easily
accessible.
❏Even if the system is turned off via the power buttons there is still a standby-voltage of 5 V on the baseboard. The
system is not completely disconnected from the mains power supply by turning off via the power button.
Hints for DC power connection:
The device must be connected only to a LPS (Limited Power Supply) DC mains power supply complying with the
requirements of EN 60950-1. The DC main power supply should be able to be switched off and on via disconnecting
device (UL-listed).
The unit is only completely disconnected from the DC mains power supply, when the DC power cord is disconnected
either from the power source or the unit. Therefore, the DC power cord and its connectors must always remain easily
accessible.
Hints for optional AC power connection:
Use only a LPS (Limited Power Supply) power supply complying with the requirements of EN 60950-1 to connect the
system to an AC power source. The main power cable of the optional external LPS power supply serves as
disconnecting device. For this reason the outlet of the AC power source must be located near to the device and be
easily accessible.
❏Do not place the device in direct sunlight, near heat sources or in a damp place. Make sure the device has adequate
ventilation.
❏Only devices and components which fulfill the requirements of an SELV circuit (safety extra low voltage) in accordance
with EN60950-1 may be connected to the interfaces of the system.
❏All plugs on the connection cables must be screwed or locked to the housing.
❏The device is designed to be mounted and operated only in the position described in this document.
❏Repairs may only be carried out by a person authorized by Kontron Europe.
❏Maintenance or repair on the open device may only be done out by qualified personnel authorized by Kontron Europe
which is aware of with the associated dangers.
❏The device may only be opened for the installation and removal of PCI/PCIe cards in accordance with the description
in this manual. These procedures have to be carried-out only by qualified specialist personnel.
❏If extensions are made to the device the legal stipulations and the device specifications must be observed.
www.kontron.com 7
StockCheck.com

4. General Safety Instructions for IT Equipment V Panel Express – User’s Guide (V1.01)
❏The device must be turned off and disconnected from the main power source, before installation and removal of any
PCI and CompactFlash™ cards.
❏The mounting and operation of the V Panel Express is the vertical position with the interfaces downwards.
❏Only original accessories approved by Kontron Europe may be used.
❏The DC-input must fulfill SELV requirements of EN60950-1 standard.
❏It must be assumed that safe operation is no longer possible,
•if the device has visible damage or
•if the device no longer functions.
In these cases the device must be shut down and secured against unintentional operation.
8www.kontron.com
StockCheck.com

4. General Safety Instructions for IT Equipment V Panel Express –User’s Guide (V1.01)
4.1. Electrostatic Discharge (ESD)
A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper
packaging and grounding techniques are necessary precautions to prevent damage. Always take the following
precautions:
1. Transport boards in ESD-safe containers such as boxes or bags.
2. Keep electrostatic sensitive parts in their containers until they arrive at the ESD-safe workplace.
3. Always be properly grounded when touching a sensitive board, component, or assembly.
4. Store electrostatic-sensitive boards in protective packaging or on antistatic mats.
4.1.1. Grounding Methods
The following measures help to avoid electrostatic damages to the device:
1. Cover workstations with approved antistatic material. Always wear a wrist strap connected to workplace as well as
properly grounded tools and equipment.
2. Use antistatic mats, heel straps, or air ionizers for more protection.
3. Always handle electrostatically sensitive components by their edge or by their casing.
4. Avoid contact with pins, leads, or circuitry.
5. Turn off power and input signals before inserting and removing connectors or connecting test equipment.
6. Keep work area free of non-conductive materials such as ordinary plastic assembly aids and styrofoam.
7. Use field service tools such as cutters, screwdrivers, and vacuum cleaners which are conductive.
8. Always place drives and boards PCB-assembly-side down on the foam.
4.2. Instructions for the Lithium Battery
The implemented ETX baseboard is equipped with a Lithium battery. For the replacing of this battery please observe the
instructions described in the section 8.3 “Replacing the Lithium Battery”.
Caution
Danger of explosion when replacing with wrong type of battery. Replace only with the same or equivalent
type recommended by the manufacturer. The lithium battery type must be UL recognized.
Do not dispose of lithium batteries in general trash collection. Dispose of the battery according to the
local regulations dealing with the disposal of these special materials, (e.g. to the collecting points for
dispose of batteries).
www.kontron.com 9
StockCheck.com

5. Electromagnetic Compatibility (Class A Device) V Panel Express – User’s Guide (V1.01)
5. Electromagnetic Compatibility (Class A Device)
5.1. Electromagnetic Compatibility (EU)
This product is intended only for use in industrial areas. The most recent version of the EMC guidelines (EMC Directive
2004/108/EC) and/or the German EMC laws apply. If the user modifies and/or adds to the equipment (e.g. installation of
add-on cards) the prerequisites for the CE conformity declaration (safety requirements) may no longer apply.
Warning!
This is a class A product. In domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
5.2. FCC Statement (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
5.3. EMC Compliance (Canada)
The method of compliance is self-declaration to Canadian standard ICES-003:
(English): This Class A digital apparatus complies with the Canadian ICES-003.
(French): Cet appareil numérique de la class A est conforme à la norme NMB-003 du Canada.
10 www.kontron.com
StockCheck.com

6. Scope of Delivery V Panel Express –User’s Guide (V1.01)
6. Scope of Delivery
Please check that your package is complete, and contains the items below (according to the ordered unit configuration).
If you discover damaged or missing items, please contact your dealer.
❏V Panel Express (configuration delivered as ordered)
❏General Safety Instruction for IT Equipment
V Panel Express system in the configuration ordered:
•V Panel Express 121
•V Panel Express 150
•V Panel Express 170
•V Panel Express 190
Note: the mounting clamps are delivered not assembled.
Phoenix Power Plug Terminal
Stylus (Touch Pen)
8x Mounting Clamp with Allen Screws for the following systems:
V Panel Express 150, V Panel Express 170 and V Panel Express 190
6x Mounting Clamp with Allen Screws for V Panel Express 121
Note: the mounting clamps are delivered not assembled.
6.1.1. Optional Parts
❏CF card (Type I)
❏RS422/485 Module (isolated or non isolated)
❏External power supply (refer to Fig. 33)
The serial interface marked “COM4” (Fig. 8, pos. 21) is an option and can be ordered as RS232, RS422 or
RS485 interfaces (isolated or non isolated). Only factory configuration is possible.
6.2. Type Label and Product Identification
The type label with the corresponding Kontron product part number is at the rear right hand side of the system.
System Type Product Designation Product Identification
V Panel Express 2-AOH8-xxxx for V Panel Express with ETXexpress-PM Module
V Panel Express 2-AOH8-xxxx for V Panel Express with ETXexpress-CD Module
Panel Express 2-AOH8-xxxx for V Panel Express with ETXexpress-PC Module
On the type label of your system, the "xxxx" group is replaced by Arabic numerals combination according to the ordered
system configuration.
www.kontron.com 11
StockCheck.com

7. Product Description V Panel Express – User’s Guide (V1.01)
7. Product Description
The V Panel Express is an industrial machine designed for high industrial application. The V Panel Express is a workstation
system with integrated touch screen display. The system is designed for:
❏Installation in an instrument panel or other cabinets
❏Installation by a VESA 75/100 compliant mounting system
All versions are suitable for installation in an instrument panel or other cabinet.
V Panel Express systems will be mounted in an instrument panel or other cabinets using the
corresponding supplied mounting clamps.
The hardware of the V Panel Express system can be flexibly configured corresponding to customized requirements. The
rugged design offers excellent mechanical stability. The V Panel Express provides the demanding characteristics required
for a computer that is very suitable for using in harsh industrial environment.
The system accommodates an ETX Express baseboard with an ETXexpress®module. Depending on the ordered system
configuration, your V Panel Express can be equipped with the ETXexpress®-PM or ETXexpress®-CD or ETXexpress®-PC
module. An installed PCI riser card allows unit expansion up to two PCI cards (32bit@33 MHz).
Depending on the system configuration ordered, the built-in display can be as a 12.1", 15", 17" or 19" TFT-LCD display.
Depending on the system configuration ordered, the V Panel Express can be equipped optionally with following external
accessible drives:
❏Up to two 2.5"SATA (I or II) HDD) (installed into a removable drive tray) and
❏Up to two Compact Flash™-cards, type I.
The power button, the RESET button, the LED control indicators and user interfaces such as DVI-I/VGA, USB (2.0)
LAN ports (10/100Mbps or 1Gbps) and serial ports (RS232) are accessible on the interface side of the system.
The V Panel Express is a fanless system. The cooling of the unit is performed by the heat sink surface of the chassis (rear
side).
The V Panel Express is designed to be connected to a +24VDC (+/-20%) mains power supply (limited power supply) using
the DC power terminal (included). In order to connect the system to an AC power supply can be ordered the optional
external AC/DC adapter (limited power supply).
Optionally, the V Panel Express systems can be equipped with additional serial interface (COM4) factory configured as
RS232/RS422/RS485 via a corresponding internal interface module.
The serial interface marked “COM4” (Fig. 8, pos. 21) is an option and can be ordered as RS232,
RS422 or RS485 interfaces (isolated or non isolated). Only factory configuration is possible.
When powering on the V Panel Express, make sure that the air intake and exhaust openings are not
obstructed.
The V Panel Express system is designed to comply with IP65 Protection class at the front side.
The V Panel Express systems only comply with IP65 protection class at the front side, if the front side
USB connector is covered by the elastic captive rubber coat.
The access door and HDD drive tray must be secured by the captive knurled screws during operation.
12 www.kontron.com
StockCheck.com

7. Product Description V Panel Express –User’s Guide (V1.01)
Fig. 1: Bottom view
Fig. 2: Right view Fig. 3: Frontal view Fig. 4: Left view
Fig. 5: Top view
Fig. 6: Rear view
In these pictures (Fig. 1 up to Fig. 6) the system is shown as a V Panel Express 121 unit.
www.kontron.com 13
StockCheck.com

7. Product Description V Panel Express – User’s Guide (V1.01)
7.1. Front Side View
Fig. 7: Frontal view of the V Panel Express system (shown with a 12.1" display);
1
2
3
4
1Front plate
2Covered (rubber coat) USB interface
312.1"/15"/17"/19" TFT display with touch screen
(Shown as a 12.1" display)
4Detail with removed rubber coat of the USB interface
7.1.1. USB Interface Connector on the Front Side
This connector USB 2.0 allows you to connect different USB-compatible devices to the V Panel Express system. The USB
connector is covered by an elastic captive rubber coat. The rubber coat prevents the penetration of fluid if no device is
connected.
The V Panel Express only complies with IP65 protection class at the front side, if the front side USB
connector is covered by the elastic captive rubber coat.
7.1.2. Front Plate Versions
All versions are suitable for installation in an instrument panel or other cabinet. At the front side are located:
❏Front plate (aluminum front plate with polyester front foil).
Depending on the size of the integrated display (12.1"/15"/17"/19"), the outline dimensions of display unit are:
(refer also to the section 12.2 “Mechanical Specifications”).
14 www.kontron.com
StockCheck.com

7. Product Description V Panel Express –User’s Guide (V1.01)
7.1.3. Display with Touch Screen
Depending on the ordered V Panel Express system the built-in display is a 12.1"/15"/17"/19" size TFT display with
corresponding resistive touch screen. The touch screen is USB connected.
For technical specification of the built-in display refer to the chapter 12 “Main Specifications”.
The display is equipped with a resistive touch screen. The touch screen offers the same degree of user comfort as the
mouse buttons. A stylus is supplied for touch screen operation.
The surface of the display is also mechanically protected through the touch screen. The touch screen (USB connected)
registers contacts of a finger or a pen and allows moving the mouse pointer. Use a stylus (included) for best results. This
functions only under integration of the necessary software. You get the corresponding touch screen driver for your
operating system, installed on your V Panel Express system (refer to section 10.2 “Operating System and Hardware
Component Drivers”. For recalibration of the touch if necessary, please observe the subsection 10.2.1.3 “Calibrating the
Touch Screen”.
Do not use a hard or a pointed object (like screw drivers) to operate the touch screen, since it can
damage the touch screen surface.
The front panel and the touch screen are covered by a plastic overlay and care should be taken when
cleaning it (see the section 11.1 “Touch Screen Care and Cleaning”).
www.kontron.com 15
StockCheck.com

7. Product Description V Panel Express – User’s Guide (V1.01)
7.2. Bottom Side (with Interfaces)
2 321
20
19
18
16
10
7
1 54
17
15
9
8
6
1312 1111 12 1111 14 14
Fig. 8: V Panel Express (interface side)
14x USB (2.0) connector
2LAN2 interface connector
3LAN1 interface connector
4Power button
5LED control indicators
62x Free expansion slots for PCI cards 32bit@33MHz
(half size)
7COM1 (RS232) and COM2 (RS232) serial ports
8RESET butoon
9DC power plug (for 24 VDC)
10 HDD drive tray with knurled screws
11 Mounting slots and screws with installed mounting clamp
12 Mounting clamp
13 Display enclosure
14 Front panel with seal on the rear side
15 CF1 slot (not equipped)
16 Screw used for grounding
17 Express Card slot
18 CF2 slot with eject button (shown with installed CF
card (type I) (option)
19 DVI-I/VGA connector
20 COM4 RS 232/422/485port connector (option)
21 COM3 (RS232)
Note for mounting clamps:
The V Panel Express 121/150/170/190 system will be secured into an instrument panel or a cabinet with
two mounting clamps on the bottom side [refer to (Fig. 8, pos. 12)].
16 www.kontron.com
StockCheck.com

7. Product Description V Panel Express –User’s Guide (V1.01)
7.2.1. DC-IN Power Connector
The V Panel Express system is supplied with the 3-pin Phoenix power connector terminal (Fig. 32). The DC Power
connector (Fig. 8, pos. 9 and Fig. 9) provides the power connection of the V Panel Express system to the main power
source via a DC power cable (not included) or the AC/DC adapter (not included; refer to the subsection 6.1.1 “Optional
Parts”). For pin-assignment of this connector refer to the section 13.1 “Power Connector”.
Fig. 9: Detail of the DC Power connector shown without Phoenix terminal
7.2.2. Power Button
3
2
1
1Power button
2HDD LED
3Power LED
Fig. 10: Power button and LED indicators
The power button “PWR ON” (Fig. 10, pos. 3) is located on the bottom side of the system (Fig. 8, pos. 4).
Press this button in order to turn the system on or off. The power button behavior can be set in the BIOS Setup: Restore
AC power loss/Option settings: Power on/Power off/Last State). The system is delivered with the default settings.
Even when the system is turned off via the power button there is still a standby-voltage of 5 V on the
baseboard. The system is not completely disconnected from the main power supply by turning off via the
power button.
Hints for DC power connection:
The device must be connected only to a LPS (Limited Power Supply) DC mains power supply complying
with the requirements of EN 60950-1. The DC main power supply should be able to be switched off and on
via a 2-pole isolating switch (UL listed).
The unit is only completely disconnected from the DC main power supply, when the DC power cord is
disconnected either from the DC main or the unit. Therefore, the DC power cord and its connectors must
always remain easily accessible.
Hints for AC power connection:
Use only a LPS (Limited Power Supply) power supply complying with the requirements of EN-60950-1 to
connect the system to an AC power source. The main power cable of the optional external LPS power
supply serves as disconnecting device. For this reason the outlet of the AC power source must be located
near to the device and be easily accessible.
7.2.3. Grounding Screw (M4) with lock Washers
The chassis of the V Panel Express system must be grounded by establishing a large-area contact between the grounding
screw M4x19 (DIN7985) with 2x lock washer M4 (DIN6797) (Fig. 8, pos. 16), and an appropriate grounding connection
point. The minimum cross section of the grounding conductor is 1mm2(AWG 18).
www.kontron.com 17
StockCheck.com

7. Product Description V Panel Express – User’s Guide (V1.01)
7.2.4. LED Control Indicators
The V panel Express is equipped with two LED indicators (Fig. 10, pos. 2 and 3) (bottom, rear side, Fig. 8, pos. 5).
Lights up green when the system is powered on via the power button.
Power LED
Lights up red when the system is in standby (depends on the behavior of the power button (BIOS Setup
setting).
HDD LED Lights up red for hard disk activity.
7.2.4.1. Power LED Error Codes
The power LED (Fig. 10, pos. 3) shows the on/off state of the system and four important malfunction conditions of the
system:
Fig. 11: Power LEDs and Error Codes
These errors will be notified by the blinking of the Power LEDs and by a beeper. The following illustration shows the blink
for different conditions.
The audible warning signal is in an inverted phase to the LED blinking (Power O.K. without beep).
If more than one malfunction condition occurs simultaneously, only the highest priority error code will be shown.
The priority order is:
1. most Voltage Error
2. less Temperature Error
3. less Fan Error
4. at least Battery Error
If more than one error occurs at the same time, only the error with the highest priority will be displayed.
7.2.5. CompactFlash™ Slot (with optional installed CF Card)
The V Panel Express is equipped with a bottom side accessible CompactFlash™ slot with eject button (Fig. 8, pos. 18). The
CF slot will accept only CF cards type I. The second CF slot (Fig. 8, pos. 15) is not equipped.
The system must be powered down before the Compact Flash™ card can be installed or removed.
CF slots (CF1 or CF2 or both) without installed CF card are covered by a slot cover as shown in
Fig. 8, pos. 15.
18 www.kontron.com
StockCheck.com