Kontron F632 User manual


USER GUIDE
www.kontron.com // 1
FlatView XXL Monitor
Doc. User Guide Rev. 1.0
Doc. ID: 1062-2144

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 2
This page has been intentionally left blank

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 3

FLATVIEW XXL
MONITOR - USER GUIDE
Disclaimer
Kontron would like to point out that the information contained in this user guide may be subject to alteration,
particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee
on the part of Kontron with respect to technical processes described in the user guide or any product characteristics
set out in the user guide. Kontron assumes no responsibility or liability for the use of the described product(s),
conveys no license or title under any patent, copyright or mask work rights to these products and makes no
representations or warranties that these products are free from patent, copyright or mask work right infringement
unless otherwise specified. Applications that are described in this user guide are for illustration purposes only.
Kontron makes no representation or warranty that such applications will be suitable for the specified use without
further testing or modification. Kontron expressly informs the user that this user guide only contains a general
description of processes and instructions which may not be applicable in every individual case. In cases of doubt,
please contact Kontron.
This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the
express written permission of Kontron. Kontron points out that the information contained in this user guide is
constantly being updated in line with the technical alterations and improvements made by Kontron to the products
and thus this user guide only reflects the technical status of the products by Kontron at the time of publishing.
Brand and product names are trademarks or registered trademarks of their respective owners.
©2018 by Kontron S&T AG
Kontron S&T AG
Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
www.kontron.com

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 4
High Risk Applications Hazard Notice
THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE
OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL OR
COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC CONTROL, LIFE
SUPPORT OR LIFE SUSTAINING APPLICATIONS, WEAPONS SYSTEMS, OR ANY OTHER APPLICATION IN A
HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE, OR IN WHICH THE FAILURE OF
PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL OR
ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS").
You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at
your risk. To minimize the risks associated with your products and applications, you should provide adequate design
and operating safeguards. You are solely responsible for compliance with all legal, regulatory, safety, and security
related requirements concerning your products. You are responsible to ensure that your systems (and any Kontron
hardware or software components incorporated in your systems) meet all applicable requirements. Unless otherwise
stated in the product documentation, the Kontron device is not provided with error-tolerance capabilities and cannot
therefore be deemed as being engineered, manufactured or setup to be compliant for implementation or for resale as
device in High Risk Applications. All application and safety related information in this document (including application
descriptions, suggested safety measures, suggested Kontron products, and other materials) is provided for reference
only.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 5
Revision History
Revision Brief Description of Changes Date of Issue Author
/ Editor
1.0 Initial version 2018-Feb-21 CW
Terms and Conditions
Kontron warrants products in accordance with defined regional warranty periods. For more information about
warranty compliance and conformity, and the warranty period in your region, visit http://www.kontron.com/terms-
and-conditions.
Kontron sells products worldwide and declares regional General Terms & Conditions of Sale, and Purchase Order
Terms & Conditions. Visit http://www.kontron.com/terms-and-conditions.
For contact information, refer to the corporate offices contact information on the last page of this user guide or visit
our website CONTACT US.
Customer Support
Find Kontron contacts by visiting: http://www.kontron.com/support.
Customer Service
As a trusted technology innovator and global solutions provider, Kontron extends its embedded market strengths into
a services portfolio allowing companies to break the barriers of traditional product lifecycles. Proven product
expertise coupled with collaborative and highly-experienced support enables Kontron to provide exceptional peace of
mind to build and maintain successful products.
For more details on Kontron’s service offerings such as: enhanced repair services, extended warranty, Kontron
training academy, and more visit http://www.kontron.com/support-and-services/services.
Customer Comments
If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact
Kontron support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the
revised user guide on our website.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 6
Symbols
The following symbols may be used in this user guide
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
NOTICE indicates a property damage message.
CAUTION indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury.
Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60
V) when touching
products or parts of products
. Failure to observe the precautions indicated and/or
prescribed by the law may endanger your life/health and/or result in damage to your
material.
ESD Sensitive Device!
This symbol and title inform that the electronic boards and their components are sensitive
to static electricity. Care must therefore be taken during all handling operations and
inspections of this product in order to ensure product integrity at all times.
HOT Surface!
Do NOT touch! Allow to cool before servicing.
Laser!
This symbol inform of the risk of exposure to laser beam and light emitting devices (LEDs)
from an electrical device. Eye protection per manufacturer notice shall review before
servicing.
This symbol indicates general information about the product and the user guide.
This symbol also indicates detailed information about the specific product configuration.
This symbol precedes helpful hints and tips for daily use.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 7
For Your Safety
Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its
compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life
expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are
requested to conform with the following guidelines.
High Voltage Safety Instructions
As a precaution and in case of danger, the power connector must be easily accessible. The power connector is the
product’s main disconnect device.
Warning
All operations on this product must be carried out by sufficiently skilled personnel only.
Electric Shock!
Before installing a non hot-swappable Kontron product into a system always ensure that
your mains power is switched off. This also applies to the installation of piggybacks. Serious
electrical shock hazards can exist during all installation, repair, and maintenance operations
on this product. Therefore, always unplug the power cable and any other cables which
provide external voltages before performing any work on this product.
Earth ground connection to vehicle’s chassis or a central grounding point shall remain
connected. The earth ground cable shall be the last cable to be disconnected or the first
cable to be connected when performing installation or removal procedures on this product.
Special Handling and Unpacking Instruction
ESD Sensitive Device!
Electronic products and their components are sensitive to static electricity. Therefore, care
must be taken during all handling operations and inspections of this product, in order to
ensure product integrity at all times.
Do not handle this product out of the products protective enclosure while the product is not used for operational
purposes unless it is otherwise protected.
Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not
guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands
or tools. This is most easily done by touching a metal part of your system housing.
It is particularly important to observe standard anti-static precautions when changing piggybacks, ROM devices,
jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the product is not placed
on conductive surfaces, including anti-static plastics or sponges. They can cause short circuits and damage the
batteries or conductive circuits on the product.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 8
Lithium Battery Precautions
If your product is equipped with a lithium battery, take the following precautions when replacing the battery.
Danger of explosion if the battery is replaced incorrectly.
Replace only with same or equivalent battery type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
General Instructions on Usage
In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or
modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received
from Kontron Support as a special handling instruction, will void your warranty.
This product should only be installed in or connected to systems that fulfill all necessary technical and specific
environmental requirements. This also applies to the operational temperature range of the specific board version
that must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.
In performing all necessary installation and application operations, only follow the instructions supplied by the
present user guide.
Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship
the product then re-pack it in the same manner as it was delivered.
Special care is necessary when handling or unpacking the product. See Special Handling and Unpacking Instruction.
Quality and Environmental Management
Kontron aims to deliver reliable high-end products designed and built for quality, and aims to complying with
environmental laws, regulations, and other environmentally oriented requirements. For more information regarding
Kontron’s quality and environmental responsibilities, visit http://www.kontron.com/about-kontron/corporate-
responsibility/quality-management.
Disposal and Recycling
Kontron’s products are manufactured to satisfy environmental protection requirements where possible. Many of the
components used are capable of being recycled. Final disposal of this product after its service life must be
accomplished in accordance with the applicable country, state, or local laws or regulations.
WEEE Compliance
The Waste Electrical and Electronic Equipment (WEEE) Directive aims to:
Reduce waste arising from electrical and electronic equipment (EEE)
Make producers of EEE responsible for the environmental impact of their products, especially when the product
become waste
Encourage separate collection and subsequent treatment, reuse, recovery, recycling and sound environmental
disposal of EEE
Improve the environmental performance of all those involved during the lifecycle of EEE
Environmental protection is a high priority with Kontron.
Kontron follows the WEEE directive.
You are encouraged to return our products for proper disposal.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 9
Table of Contents
Symbols.................................................................................................................................................................................................................6
For Your Safety ...................................................................................................................................................................................................7
High Voltage Safety Instructions ..................................................................................................................................................................7
Special Handling and Unpacking Instruction ............................................................................................................................................7
Lithium Battery Precautions.......................................................................................................................................................................... 8
General Instructions on Usage..................................................................................................................................................................... 8
Quality and Environmental Management................................................................................................................................................ 8
Disposal and Recycling.................................................................................................................................................................................... 8
WEEE Compliance.............................................................................................................................................................................................. 8
Table of Contents...............................................................................................................................................................................................9
List of Tables .....................................................................................................................................................................................................10
List of Figures....................................................................................................................................................................................................10
1/ Introduction ..........................................................................................................................................................................................11
2/ General Safety Instructions for IT Equipment.........................................................................................................................12
Electrostatic Discharge (ESD)...............................................................................................................................................................132.1.
2.1.1. Grounding Methods ...............................................................................................................................................................................13
3/ Scope of Delivery and Accessories..............................................................................................................................................14
Type Label and Product Identification ...............................................................................................................................................143.1.
Product Variants.......................................................................................................................................................................................153.2.
4/ Technical Data ....................................................................................................................................................................................16
Electrical Specification............................................................................................................................................................................164.1.
Environmental Specification ................................................................................................................................................................174.2.
Standards and Approvals......................................................................................................................................................................174.3.
4.3.1. CE ................................................................................................................................................................................................................17
4.3.2. Electromagnetic Compatibility.........................................................................................................................................................17
4.3.3. RoHS..........................................................................................................................................................................................................17
4.3.4. WEEE.........................................................................................................................................................................................................17
Mechanical Specification.......................................................................................................................................................................184.4.
4.4.1. 32” Full Metal Variant (F632) ............................................................................................................................................................18
4.4.2. 42” Full Metal Variant (F642) ...........................................................................................................................................................19
4.4.3. 55” Full Metal Variant (F655) ............................................................................................................................................................19
4.4.4. 65” Full Metal Variant (F665)...........................................................................................................................................................20
5/ Product Description ..........................................................................................................................................................................21
Front View...................................................................................................................................................................................................225.1.
Rear View....................................................................................................................................................................................................235.2.
5.2.1. Back Panel Views ..................................................................................................................................................................................23
I/O Interface Connections..................................................................................................................................................................... 255.3.
6/ Configuration......................................................................................................................................................................................26
7/ Installation and Starting Up.......................................................................................................................................................... 27
Mounting Instructions ............................................................................................................................................................................ 277.1.
7.1.1. Mounting by Hanging ........................................................................................................................................................................... 27
7.1.2. Mounting Orientation .......................................................................................................................................................................... 27
Starting Up ................................................................................................................................................................................................. 277.2.
8/ System Settings with On-Screen Display Menu ....................................................................................................................29
OSD Menu ...................................................................................................................................................................................................308.1.
9/ Standard Interface Connector – Pin outs.................................................................................................................................38

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 10
10/ Technical Support............................................................................................................................................................................. 39
Troubleshooting .....................................................................................................................................................................................3910.1.
11/ Warranty ..............................................................................................................................................................................................40
Limitation/Exemption from Warranty Obligation........................................................................................................................4011.1.
Returning Defective Merchandise .....................................................................................................................................................4111.2.
12/ Storage, Transportation and Maintenance .............................................................................................................................43
Storage.......................................................................................................................................................................................................4312.1.
Transportation........................................................................................................................................................................................4312.2.
Maintenance............................................................................................................................................................................................4312.3.
12.3.1. Cleaning the Screen............................................................................................................................................................................43
12.3.2. Cleaning the Housing ........................................................................................................................................................................43
13/ Disposal................................................................................................................................................................................................44
Appendix A: List of Acronyms......................................................................................................................................................................45
List of Tables
Table 1: Scope of Delivery ..............................................................................................................................................................................14
Table 2: Optional Accessories ......................................................................................................................................................................14
Table 3: Technical Data ..................................................................................................................................................................................16
Table 4: Power Specification ........................................................................................................................................................................16
Table 5: Environmental Specifications......................................................................................................................................................17
Table 6: Mechanical Dimensions.................................................................................................................................................................18
Table 7: Back Panel Mechanical Features - 32”, 42” and 55” Displays .......................................................................................... 23
Table 8: Back Panel Mechanical Features – 65” Displays..................................................................................................................24
Table 9: USB Client Connector Pinout.......................................................................................................................................................38
Table 10: DP Connector Pinout ....................................................................................................................................................................38
Table 11: DVI Connector Pinout....................................................................................................................................................................38
Table 12: Troubleshooting ............................................................................................................................................................................39
Table 13: List of Acronyms............................................................................................................................................................................45
List of Figures
Figure 1: FlatView XXL Monitor .....................................................................................................................................................................11
Figure 2: Type Label.........................................................................................................................................................................................14
Figure 3: 32” Full Metal Variant (F632).....................................................................................................................................................18
Figure 4: 42” Full Metal Variant (F642).....................................................................................................................................................19
Figure 5: 55” Full Metal Variant (F655)......................................................................................................................................................19
Figure 6: 65” Full Metal Variant (F665).....................................................................................................................................................20
Figure 7: Front View........................................................................................................................................................................................22
Figure 8: Rear View .........................................................................................................................................................................................23
Figure 9: OSD Keys ..........................................................................................................................................................................................29

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 11
1/ Introduction
This user guide describes the FlatView XXL Monitor made by Kontron, also denoted as FlatView XXL within this user
guide. This user guide focuses on describing the FlatView XXL special features. New users are recommended to study
the short installation instructions within this user guide before switching on the power.
The Kontron FlatView XXL series with its brilliant and large screens up to 65-inch opens the door to meaningful, clear
and comprehensive visualization. The industrial grade design includes an IP54 sealed metal housing and guarantees a
reliable 24x7 operation even in challenging environments. Both front options, IR-touch screen and protection glass,
provide a robust, scratch proof and easy to clean front surface.
All displays feature Full-HD resolution and, in case of even higher resolution requirements, Ultra-HD (4k) displays are
also available. Typical applications are process visualization, plant data collection and manufacturing execution
systems. Furthermore, due to the FlatViews XXL’s thoroughly modular design the FlatView XXL series can be easily
customized to meet specific individual application needs.
General FlatView XXL features are:
Display sizes 32” to 65” with and without touch
Full-HD with optional Ultra-HD
VESA wall mount possible
Fanless use
Modular mechanical design.
Industrial grade: Robust, reliable versatile and maintenance –free
Self explaining OSD (On-Screen Display)
Additionally, when developing our products we exclusively use embedded components to meet the current
requirements and support sustainability for the future (Industry 4.0) such as long-term availability of embedded
components.
Figure 1: FlatView XXL Monitor

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 12
2/ General Safety Instructions for IT Equipment
Read these safety instructions carefully and observe the instructions for your own safety, and correct use of the
product. Additionally, observe all warnings and instructions on the product and within this user guide.
Read this chapter carefully and take careful note of the instructions that have been
compiled for your safety. If the following general safety instructions are not observed, it
could lead to injuries to the operator and/or damage of the product; in cases of
nonobservance of the instructions Kontron is exempt from accident liability, this also
applies during the warranty period.
The product has been built and tested according to the basic safety requirements and has left the manufacturer in a
safety-related, flawless condition. To maintain this condition and also to ensure safe operation, the operator must not
only observe the correct operating conditions for the product but also the following general safety instructions.
Product
Do not insert sharp objects or spill liquid through slots in the housing. They may cause accident fire, electric shock
or failure
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous
voltage points or other risks
Do not touch the screen directly with your fingers. You may damage the screen, and oil from your skin is difficult to
remove
Do not apply excess pressure to the screen
Power and Power plug
Use the type of power indicated on the type label
The power cable serves as a disconnecting device. For this reason, the outlet of the power source must be located
near the product and be easily accessible.
The electrical installations must correspond to the requirements of local (country-specific) regulations.
Disconnect the power plug from the AC outlet under following conditions:
If not in use for an extended period time.
When the power cord or plug is damaged or frayed.
If the product does not operate normally when the operating instructions are followed.
If the product exhibits a distinct change in performance, service may be required.
Cables
Do not allow anything to rest on the power cord.
Take care that there are no cables, particularly power cables, in areas where persons can trip over them.
Do not locate this product where persons will walk on the cord.
Do not overload wall outlets or power cords. Ensure that the total of all units plugged into the wall outlet does not
exceed 10 amperes.
Ensure that the total ampere ratings on all units plugged into the extension cord is not above the cord’s rating.
Environment
Install on a flat level surface.
Install in a well-ventilated place.
Keep away from:
Overly hot environments
Cold environments
Humid environments
Direct sunlight
Dusty environment
Equipment that generate strong magnetic fields

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 13
Electrostatic Discharge (ESD)2.1.
A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore, proper
packaging and grounding techniques are necessary precautions to prevent damage.
Always following ESD Sensitive device precautions below:
ESD Sensitive Device!
Keep electrostatic sensitive parts in their containers until they arrive at the ESD-safe
workplace. Always
be properly grounded when touching a sensitive board, component, or
assembly.
For more Information, see the Special Handling and Unpacking Instruction within this user guide and Chapter 2.1.1
Grounding Methods below.
Transport in ESD-safe containers such as boxes or bags.
Keep electrostatic sensitive parts in their containers until they arrive at the ESD-safe workplace.
Always be properly grounded when touching a sensitive board, component, or assembly.
Store electrostatic-sensitive parts in protective packaging or on antistatic mats.
2.1.1. Grounding Methods
The following measures help to avoid electrostatic damages to the device:
Cover workstations with approved antistatic material. Always wear a wrist strap connected to the workplace, as
well as properly grounded tools and equipment.
Use antistatic mats, heel straps, or air ionizers for more protection.
Always handle electrostatically sensitive components by their edge or by their casing.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting and removing connectors or connecting test equipment.
Keep the work area free of non-conductive materials such as ordinary plastic assembly aids and styrofoam.
Use field service tools such as cutters, screwdrivers, and vacuum cleaners that are conductive.
Always place drives and boards with the PCB-assembly-side down on the foam.

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 14
3/ Scope of Delivery and Accessories
Check that your package is complete, and contains the items below (according to the ordered unit configuration). If you
discover damaged or missing items, contact your dealer.
Table 1: Scope of Delivery
Description
FlatView XXL (32”, 42”, 55” or 65”) display
Safety Instructions for IT equipment
Cabling is factory installed for the 32”, 42” and 55” displays.
All 65” displays come with the customer ordered cable, for customer configuration. For more
information on available cables types and lengths, see Chapter 3.2: Product Variants.
Table 2: Optional Accessories
Description
VCM Universal Wall Mount
Available on customer request
Type Label and Product Identification3.1.
To identify the product refer to the type label positioned on the rear side of the housing.
Figure 2: Type Label
1.
Product name
2. Model number with barcode
3. Serial Number (S/N) with barcode
4. For internal production use
5. Certification information
6. Technical data
3
2
1
4
5
6

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 15
Product Variants3.2.
The FlatView XXL series of large screen closed case industrial grade monitor variants are:
1. Housing: F6 -Full metal Closed housing (IP54)
2. Display size: 32”
42”
55”
65”
3. Touch screen: IR-touch
Protection glass (without IR-touch)
4. Further options:
Cables
DVI 2 m, 3 m and 5 m
DP 1.8 m, 3 m and 5 m
USB 2.0 Type A -2 m, 3 m and 5 m

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 16
4/ Technical Data
Table 3: Technical Data
Display Size 32” 42” 55” 65” 65”
Display Manufacturer LG AUO AUO AUO AUO
Display Type LD320EUN-SEM1 P420HVN03.1 P550HVN02.2 P650HVN03.0 P650HVN04.0
Resolution 1920x1080,
Full-HD
1920x1080,
Full-HD
1920x1080,
Full-HD
1920x1080,
Full-HD
1920x1080,
Full-HD
Format 16:9 16:9 16:9 16:9 16:9
Contrast Ratio 1300:1 4000:1 4000:1 4000:1 4000:1
Brightness 400 cd/m2 700 cd/m2 500 cd/m2 500 cd/m2 700 cd/m2
Angle View 178°/178° 178°/178° 178°/178° 178°/178° 178°/178°
Colors 16.7 million 16.7 million 16.7 million 16.7 million 16.7 million
LED Lifetime
(> 50%, 25°C)
50.000 h 50.000 h 50.000 h 50.000 h 50.000 h
Dimensions
W x H x D (mm)
780x475x96.5 1050x640x132 1302x787x145 1547x931x181.5 1547x931x181.5
Weight ~ 20 kg ~ 40 kg ~ 60 kg ~ 75 kg ~ 75 kg
Touch Options Protection glass, IR-touch
Mounting Option Full metal housing
Fastening VESA 200/200 or 200/up to 600 VESA 200/400 VESA 200-600/200-1000
Color RAL 7021 (black anthracite)
Cooling Fanless passive cooling
Video IN 1x DVI, 1x Display Port
I/O Options USB 2.0 (Type A) – only for IR-touch variants
Protection Class IP54
Certification CE
EMC EN55022 Class A
Electrical Specification4.1.
All FlatView XXL series are AC voltage systems designed for direct connection to the mains AC power source. The power
cable is either brought out of the housing using one of the two lead-through or for the 65-inch display variants is
available as a connector on the back panel, see Table 8: Back Panel Mechanical Features – 65” Displays.
Before, connecting the power cable to the power source ensure that the power source meets the power requirements
specified on the FlatView XXL Type label, and the requirements of local (country-specific) regulations.
For grounding, the protective earth connection is positioned on the rear side of the housing next to the main power
supply switch.
For AC power connection. The power source must meet the power requirement specified
on the FlatView XXL type label.
Table 4: Power Specification
Display Size 32” 42” 55” 65” 65”
Power Supply (V AC ) 90 V AC to 264 V AC, at 47 Hz to 63 Hz

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 17
Environmental Specification4.2.
The FlatView XXL series conforms to the following environmental specifications.
Table 5: Environmental Specifications
Operating Temperature 0°C - 45°C ambient
Humidity 10%-90% @ 39°C, non condensing
Standards and Approvals4.3.
The FlatView XXL series conforms to the requirements of the following standards.
If the user modifies the product, prerequisites for specific approvals such as CE conformity
declaration (safety requirements) may no longer apply.
4.3.1. CE
This product is CE certified.
4.3.2. Electromagnetic Compatibility
This product has been designed for low level of radiated emission for residential, commercial and light-industrial
environments and high immunity level for industrial environmental and complies with the EN 55022 class A
specification for radiated and conducted emissions.
EN 55022 Class A Emission of Information Technology Equipment (ITE), radio disturbance characteristics
and limits and methods of measurement (Class A)
4.3.3. RoHS
RoHS II Directives Compliant with the directive on the restriction of the use of certain hazardous
substances in electrical and electronic equipment
4.3.4. WEEE
WEEE Directive Compliant with the Waste Electrical and Electronic Equipment (WEEE) Directive to
reduce waste of electrical and electronic equipment, encourage recycling and
environmental disposal and increase the environmental awareness of producers

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 18
Mechanical Specification4.4.
Four different display sizes are available 32-inch, 42-inch, 55-inch and 65-inch. The following table lists the mechanical
dimensions of the FlatView XXl displays.
Table 6: Mechanical Dimensions
FlatView XXL 32” (F632) 42” (F642) 55” (F655) 65” (F665)
Height 780 mm
(30.71")
1050 mm
(41.34")
1302 mm
(51.26")
1547 mm
(60,91")
Width 475 mm
(18.70")
640 mm
(25.20")
775.5 mm
(30,53")
917 mm
(36,10")
Depth 96.5 mm
(3.80")
100.5 mm
(3.96")
119.5 mm
(4.70")
181.5 mm
(7.15")
For more detailed mechanical dimensions, refer to the outline dimensions drawings within this chapter. Each dimension
drawing shows the main external mechanical features such as the position and size of the VESA mounting holes,
opening hinges, OSD control panel, and cable lead through or external I/O connector panel.
4.4.1. 32” Full Metal Variant (F632)
Figure 3: 32” Full Metal Variant (F632)

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 19
4.4.2. 42” Full Metal Variant (F642)
Figure 4: 42” Full Metal Variant (F642)
4.4.3. 55” Full Metal Variant (F655)
Figure 5: 55” Full Metal Variant (F655)

FlatView XXL Monitor – User Guide Rev. 1.0
www.kontron.com // 20
4.4.4. 65” Full Metal Variant (F665)
Figure 6: 65” Full Metal Variant (F665)