Koo-di KD430 User manual

Instruction booklet
© Weybury Hildreth Ltd. 2018
IMPORTANT
Please read instructions carefully
and keep for future reference
KD430 koo-di Duo Wooden Highchair

Read all instructions before assembly and use of the high chair.
Keep instructions for future use.
1
WARNING
© Weybury Hildreth Ltd. 2018
• FOLLOW THE MANUFACTURER’ S INSTRUCTIONS.
• DO NOT USE THE HIGHCHAIR UNTIL THE CHILD CAN SIT UP UNAIDED.
• DO NOT LEAVE CHILDREN UNATTENDED.
• THE HARNESS MUST ALWAYS BE USED AND CORRECTLY ADJUSTED
- MOST INJURIES FROM HIGHCHAIRS ARE CAUSED BY FALLS.
• IMPORTANT - THE HARNESS STRAPS ARE NOT REMOVABLE!
• NOT RECOMMENED FOR USE WITHOUT THE TRAY SECURELY FITTED.
• DO NOT USE HIGHCHAIR UNLESS ALL COMPONENTS ARE
CORRECTLY FITTED AND ADJUSTED.
• POSITION THE HIGHCHAIR AWAY FROM SOLID STRUCTURES TO
AVOID INJURIES CAUSED BY FALLS AND BY ACCESS TO DANGER
OUS ITEMS.
• BE AWARE OF THE RISK OF OPEN FIRE AND OTHER SOURCES OF
STRONG HEAT, SUCH AS COOKERS, KETTLES, GAS FIRES ETC. IN THE
VICINITY OF THE HIGHCHAIR.
• INSPECT THE HIGHCHAIR REGULARLY FOR SIGNS OF WEAR. IF ANY
PARTS ARE BROKEN OR SHOW SIGNS OF EXCESSIVE WEAR, STOP
USING THE HIGHCHAIR.

© Weybury Hildreth Ltd. 2018
2
Safety Precautions
• Always keep your child in view whilst in the highchair.
• The tray is not designed to hold the child in the highchair, but
we do recommend the tray is secured in place whilst the child is
in the highchair.
• Always secure your child in the restraint, ensuring that the
harness is correctly fitted and adjusted at all times.
• Remember, do not attempt to remove the harness from the
seat, the harness is NOT removable.
• When fitting the harness straps, securing the buckles and
fitting the tray, ensure your child’s fingers are clear from any
moving parts.
• Only use the highchair on a secure, level floor.
• Do not elevate the highchair onto any structure such as a table
or worktop.
• DO NOT allow children to stand on the seat or footrest or climb
into or out of the highchair, ensure the harness is fitted and
adjusted to prevent this.
• DO NOT carry the highchair with a child in it.
• The maximum weight of the child should not exceed 17kgs or 36
months, which ever comes first, when using this product in the
highchair mode.
• Only use low chair mode when your child is 36 months or over.
• When the highchair is assembled turn the adjustable feet
ensuring all four feet sit flat to the floor surface.

You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact us by email – [e-mail].
X 1
seat
X 2 X 4
3
What’s in the box
X 1 X 1
© Weybury Hildreth Ltd. 2018
u p p e r
r e a r
l e g s
X 2
footrest
fixing
screws
t r a y &
i n n e r
t r a y
f o o t-
r e s t
lower
l e g s
X 2
u p p e r
front
l e g s
threaded
holes

2. Locating the threaded holes in the upper front leg, line up the holes in the
footrest with the holes in the upper front leg.
3.
© Weybury Hildreth Ltd. 2018
4
Connecting the upper front the legs, and the fitting the footrest
Screw Holes
1. Locate the two upper front legs. Ensure they are the legs that have the threaded holes.
As in Fig.1 below, screw the upper front leg into the base of the highchair clockwise.
Ensure that the threaded holes are facing the front. If the holes are not facing front,
tighten further until this is achieved. Repeat for opposite side.
Insert supplied fixing screws provided and tighten with a Phillips head screwdriver (not
supplied). Do not over-tighten the screws. Repeat for opposite side.
Fig.1

5
© Weybury Hildreth Ltd. 2018
Connecting the upper rear legs & lower legs
Locate the four lower legs. Screw
the lower leg into the upper leg as
shown in Fig. 4, below. Do not
over-tighten. Repeat for remaining
three legs.
5. 6. When your highchair is assembled,
adjustable feet so that all four feet
lay flat on the floor surface. see
Fig.5.
4. Locate the two upper rear legs. Line up the screw and the hole and turn clockwise until
the leg is secure as in Fig. 2. Do not over-tighten. Repeat for opposite side.
The highchair should be the same as the image in Fig.3
Fig.2 Fig.3
Fig.4 Fig.5

© Weybury Hildreth Ltd. 2018
6
Converting high chair to low seat mode
7. The highchair can also be converted into a low chair. Simply remove both upper and
lower legs, then refit the 4 lower legs directly into the bottom of the seat. Ensure the
legs are secure - Do not over-tighten.
Repeat step 6 on page 5, rotating the feet to ensure the seat sits flush on the floor
before use.
Fig.5

7
© Weybury Hildreth Ltd. 2018
1.
Attaching, removing and adjusting plastic tray
To attach the tray see Fig.6. Align the tray with the arm rests, push the button at the
front of the plastic tray while sliding tray along armrests to desired position then
release the button. To adjust tray; push the button the front of the tray and slide
forward or backward to desired position, then release the button, ensure the tray is
locked in place
2.The tray features an inner-tray, which is easily removed by locating the lip and lifting up
as shown in Fig. 7
3.To remove the plastic tray, locate the button at the front of the tray, as shown in Fig. 8.
Push the button and pull the tray outward, ensuring you secure the highchair with your
other hand to avoid accidents.
Safety Note: The plastic tray can be adjusted and has three positions, it should
always be position as near to the child as is comfortable.
Fig.6 Fig.7
Fig.8

© Weybury Hildreth Ltd. 2018
8
Securing and adjusting the safety harness
To secure your child in harness, push buckle (A) and (B) into the buckle
housing (C) until the buckle prongs snap into position.
Carefully adjust the harness by pulling the slider (D) until the desired t is
achieved in the lap, shoulder and crotch strap. Ensure the shoulder straps
To release the buckle, squeeze the top and bottom prongs until it
disengages.
shoulder
straps
(C) buckle
housing
(A) buckle
prongs
(B) buckle
prongs
(D) slider
(D) slider
1.
2.
3.
Note: The harness straps are not removable from the highchair
Fig.9

visit koo-di.com
To Clean Your Highchair
The tray and inner tray can be wiped clean using a sponge or cloth with warm
water and mild detergent. You may wish to use a baby sterilizing solution to
ensure cleanliness. To clean the seat pad wipe over with warm water and a
little mild detergent on a sponge or cloth. Do not over wet the seat and ensure
it is completely dry before use. For safety reasons, the straps are designed to
be non-removable, do not attempt to remove. To clean the straps, use warm
water and mild detergent solution, and if necessary, use a soft nail brush.
After cleaning ensure the straps are secure. Ensure any detergent is rinsed off
and the straps are dry before use. Do not use bleach, harsh chemicals or
scourers. The wooden legs can be wiped clean with a damp cloth or sponge
using warm water and mild detergent. After wiping the legs check the white
feet are flat on the floor (see step 6 on page 5)
Do not use bleach, harsh chemicals or scourers as this will damage the seat
material, plastic parts and wooden legs
Weybury Hildreth Ltd.
Bay 1& 2,Building 47 Second Avenue,
The Pensnett Estate, Kingswinford,
West Midlands, DY6 7UZ.
UK.
email: [e-mail]
tel: [phone]